• Code: E004-0505
• Description: Thermistor temperature difference error. Difference of detected temperature between thermistors is bigger than the specified value
• Remedy: 1. The connectors of the fixing main/sub thermistor (THM1-1 to 3) are physically removed (the cable is caught, or disconnected) -> replace the fixing belt unit 2. Check the rotation of the fixing motor (the connector is physically removed or disconnected) -> replace the fixing motor or the harness 3. The connectors of the pressure sub thermistor (THM2,3,4) are physically removed (the cable is caught, or disconnected) -> replace the thermistor or the presure stay 4. Disconnection, soiled, improper location of, or faulty pressure sub thermistor (THM2,3,4) -> clean the thermistor or replace it 5. Faulty drawer connector -> clean the drawer connector or replace the fixing unit 6. Replace the DC controller PCB

• Code: E004-0701
• Description: Relay off state error (circuit failure). Detected that the relay is OFF.
• Remedy: 1. Check the fixing belt -> if it is damaged, replace the fixing belt unit 2. Check the connection of the fixing fuse PCB -> replace the fuse PCB 3. Check the connection of the fixing thermoswitch (TP2) (thermoswitch is OFF, or the cable is disconnected) -> replace the fixing belt unit 4. Relay PCB replacement 5. DC controller replacement 6. IH power supply replacement

• Code: E004-0702
• Description: IH power supply relay abnormality. Voltage shows abnormal value even with the relay-off
• Remedy: 1. IH power supply replacement

• Code: E004-0801
• Description: AC driver PCB failure. Destination ID for AC driver PCB cannot be read
• Remedy: 1. PCB and wire harness replacement due to AC driver PCB failure

• Code: E006-0001
• Description: Fixing Feed drawer connection error. Fixing Feed drawer connector is abnormal (Sensor cannot detect)
• Remedy: 1. Fixing Feed drawer connector has connection failure, wire harness failure, sensor failure

• Code: E006-0002
• Description: Fixing Feed drawer connection error. Fixing feed knob of fixing drawer is abnormal (Sensor cannot detect)
• Remedy: 1. Fixing feed knob of fixing drawer has connection failure, wire harness failure, sensor failure

• Code: E007-0001
• Description: Fixing belt full displacement error (Displacement direction is unknown.). Full displacement of the fixing belt was detected, but the displacement direction (front, rear) was unknown.
• Remedy: 1. Forgot to clear the counter at the fixing belt replacement -> clear the counter 2. Check physical relationship between the fixing belt position sensor 1, 2 (PS71, 72) and the sensor flag A. In case that both sensors are blocked from light A-1. Faulty fixing belt unit -> replace the fixing belt unit A-2. Faulty fixing belt displacement control drive -> replace the displacement control drive assembly B. In case that both sensors are not blocked from light B-1. The connector on the fixing belt position sensor 1, 2 (PS71, 72) is physically removed, or the cable is disconnected -> connect the connector, or replace the harness B-2. Faulty fixing belt position sensor 1, 2 (PS71, 72) -> replace the sensor B-3. Faulty fixing belt unit -> replace the fixing belt unit B-4. Faulty fixing feed driver PCB -> replace teh fixing feed driver PCB

• Code: E007-0002
• Description: Pressure belt full displacement error (Displacement direction is unknown.). Full displacement of the pressure belt was detected, but the displacement direction (front, rear) was unknown.
• Remedy: 1. Check installation of the pressure belt displacement control drive -> correct to the right installation procedure 2. Faulty pressure belt unit -> replace the pressure belt unit 3. Faulty pressure belt position sensor 1, 2 (PS76, 77) or faulty position sensor flag -> replace the pressure stay 4. Faulty drawer connector -> clean the drawer connector or replace the fixing unit 5. Faulty fixing feed driver PCB -> replace the fixing feed driver PCB