Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Epson AcuLaser C9200N — Trang 5/11

Code: E113

Description: Laser malfunction (Black)
- SOS signal is not detected within the lapse of a given period of time after staring the laser output.
- SOS signal is not detected within a given period of time during printing or IDC sensor adjustment
Causes: • PH Unit • PH Interface Board (PWB-D) • Mechanical Control Board (PWB-M)
Remedy: 1 Check the connector for proper connection and correct as necessary. - - 2 Change PH Unit - - 3 Change PWB-D - - 4 Change PWB-M

Code: E200

Description: Transfer Belt Separation
- The 1st Image Transfer Pressure/Retraction Position Sensor doesn't turn ON (Retracting) even after the lapse of a given period of time after the 1st Image Transfer Pressure/Retraction Clutch has turned ON during the Transfer Belt is retracting.
- The 1st Image Transfer Pressure/Retraction Position Sensor doesn't turn OFF (Pressuring) even after the lapse of a given period of time after the 1st Image Transfer Pressure/Retraction Clutch has turned ON during the Transfer Belt is pressuring.
Causes: • 1st Image Transfer Pressure/Retraction Position Sensor (PC6) • 1st Image Transfer Pressure/Retraction Clutch (CL3) • Main Motor (M1) • Mechanical Control Board (PWB-M)
Remedy: 1 Check the M1 connector for proper connection and correct as necessary. - - 2 PC6 I/O check, Sensor check - - 3 CL3 operation check PWB-M CNDM1-11 (ON) K to L-2 4 M1 operation check PWB-M CNDM1-5 (REM) PWB-M CNDM1-8 (LOCK) K to L-2 5 Change PWB-M

Code: E210

Description: 2nd Transfer Roller Separation
- The 2nd Image Transfer Pressure Position Sensor doesn't turn ON (Retracting) even after the lapse of a given period of time after the 2nd Image Transfer Pressure/Retraction Motor has started rotating during the 2nd Transfer Roller is retracting.
- The 2nd Image Transfer Pressure Position Sensor doesn't turn OFF (Pressuring) even after the lapse of a given period of time after the 2nd Image Transfer Pressure/Retraction Motor has started rotating during the 2nd Transfer Roller is pressuring.
Causes: • Mechanical Control Board (PWB-M) • Right Door
Remedy: 1 Check the connector of motor for proper connection and correct as necessary. - - 2 Change Right Door - - 3 Change PWB-M

Code: E220

Description: Transfer Belt Unit New Article Release
- A new installation is not detected when a new Transfer Belt Unit is installed.
Causes: Mechanical Control Board (PWB-M)
Remedy: 1 Reinstall the Unit. - - 2 Change PWB-M

Code: E300

Description: Abnormally low Heating Roller temperature
- The temperature of the Heating Roller Thermistor/1 (TH1) is lower than a given level of degree for 1 second or more uninterruptedly during Ready mode, Low Power mode or printing.
- The temperature of the Heating Roller Thermistor/2 (TH3) is lower than a given level of degree for 1 second or more uninterruptedly during Ready mode, Low Power mode or printing.
Causes: • Fusing Unit • DC Power Supply (PU1) • Mechanical Control Board (PWB-M)
Remedy: 1 Check the Fusing Unit for correct installation (whether it is secured in position). - - 2 Check the Fusing Unit, PWB-M and PU1 for proper connection and correct or change as necessary. - - 3 Change Fusing Unit - - 4 Change PWB-M - - 5 Change PU1

Code: E301

Description: Abnormally low Fusing Pressure Roller temperature
- The temperature of the Fusing Pressure Roller Thermistor /1 (TH2) is lower than a given level of degree for 1 second or more uninterruptedly during Ready mode, Low Power mode or printing
Causes: • Fusing Unit • DC Power Supply (PU1) • Mechanical Control Board (PWB-M)
Remedy: 1 Check the Fusing Unit for correct installation (whether it is secured in position). - - 2 Check the Fusing Unit, PWB-M and PU1 for proper connection and correct or change as necessary. - - 3 Change Fusing Unit - - 4 Change PWB-M - - 5 Change PU1

Code: E302

Description: Abnormally high Heating Roller temperature
- The temperatures of the Heating Roller Thermistor/1 (TH1) and the Heating Roller Thermistor/2 (TH3) are higher than a given level of degree for 1 second or more uninterruptedly.
- The Heater Relay is OFF.
Causes: • Fusing Unit • DC Power Supply (PU1) • Mechanical Control Board (PWB-M)
Remedy: 1 Check the Fusing Unit for correct installation (whether it is secured in position). - - 2 Check the Fusing Unit, PWB-M and PU1 for proper connection and correct or change as necessary. - - 3 Change Fusing Unit - - 4 Change PWB-M - - 5 Change PU1

Code: E303

Description: Abnormally high Fusing Pressure Roller temperature
- The temperature of the Fusing Pressure Roller Thermistor/1 (TH2) is higher than a given level of degree for 1 second or more uninterruptedly before the Heater temperature control starts.
- The temperature of the Fusing Pressure Roller Thermistor/1 (TH2) is higher than a given level of degree for 1 second or more uninterruptedly after the Heater temperature control starts.
Causes: • Fusing Unit • DC Power Supply (PU1) • Mechanical Control Board (PWB-M)
Remedy: 1 Check the Fusing Unit for correct installation (whether it is secured in position). - - 2 Check the Fusing Unit, PWB-M and PU1 for proper connection and correct or change as necessary. - - 3 Change Fusing Unit - - 4 Change PWB-M - - 5 Change PU1
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie