• Code: 1130
• Description: DMA Controller Error.
  An error occurs when the DMA of the printing data cannot be completed.
• Remedy: • Replace the Main PCA.

• Code: 1140
• Description: Flash ROM Write Error
  A time-out error occurs when the flash ROM contents are being saved and erasing does not end.
• Remedy: • Replace the Main PCA.

• Code: 1150
• Description: Home Position Sensor Error
  The Carriage cannot be moved to it’s home position.
• Remedy: • Enter the Sensors Menu (in Maintenance Mode) and select "Printer Sensors". Then execute the "Home Position" option, which will display the state of the home position sensor. If the home position is detected, "1" will be displayed on the Front Panel. If the home position is not detected, manually move the Carriage and check the Front Panel to see if the "1" is displayed. • Make sure the Home Position Sensor Cable is connected correctly and is not damaged. • Replace the Home Position Sensor. • Replace the ISS PCA. • Replace the Main PCA.

• Code: 1160
• Description: Wiping Error
  When the Wiping Motor has been running for a while, the sensor fails to detect that the Motor has made one turn.
• Remedy: Check whether the Wiper Blade turns once and the Wiper Blade Position Sensor detects the turn when the Printer is initializing when it is powered On. • If the Wiper does not turn once: – Check manually by turning the Wiper Gears to see if the Wiper Blade turns. If it does not turn then replace the Wiping Station. – Check whether +24 V (LED 38) is supplied to the Main PCA by checking that LED 38 is lit on the Main PCA. If the Wiper Motor does not turn even though the +24 V is supplied, there is a possibility of a failure in the Wiper Motor. Replace the Wiping Station. – Make sure the Wiper Blade Position Sensor Cable is connected correctly and is not damaged. – If the error continues, replace the Main PCA. • If the Wiper does turn once: – Check whether the Wiper Blade Position Sensor can be switched ON and OFF by manually rotating the Wiper Blade. Check whether the lever type switch is not loose. – Make sure the Wiper Blade Position Sensor is connected correctly and is not damaged. – Make sure that the Wiper Blade Position Sensor is clean. – Replace the ISS PCA. – If the error continues, replace the Main PCA.

• Code: 1170
• Description: Temperature Sensor Error
  The Temperature Sensor detects abnormal temperatures (-10C or lower or 85C or higher).
• Remedy: • Make sure that the Printer is in an environment where the temperature is between -10oC and 85oC. • Make sure the Ambient Temperature Sensor Cable is connected correctly and is not damaged. • Replace the ISS PCA. • Replace the Main PCA.

• Code: 1180
• Description: Pump/Wipe Motor Error
  Over current is detected in the pump/wipe motor drive circuit.
• Remedy: • When the ambient temperature is very low, the Pump Motor Tube becomes hard and the load on the Capping Motor is increased. Make sure that the Printer is in an environment where the temperature is not below -10oC or higher than +85oC. • Enter the Motors Menu (in Maintenance Mode) and select "Forwards" to activate the Pump/Wipe Motor. Access the Pump Motor and check whether the Motor Drive Circuit and Motor work correctly. • Make sure that the Capping Station cables are connected correctly and are not damaged • If the Capping Motor cannot be rotated, replace the Capping Station Motor. • Make sure the Cap Sensor Cable is connected correctly and is not damaged. • Replace the Main PCA.

• Code: 119x
• Description: Printhead Drive Voltage Error
  The Printhead drive voltages generated on the Carriage PCA do not reach the expected values.
• Remedy: • Check whether VDD2 power is generated on the Main PCA. If not, then: – Make sure that the Window is closed. – Replace the Power Supply Unit. • If the power is supplied, it means that the voltage check circuit is defective. Replace the Main PCA. • Make sure the Trailing Cable is connected correctly and is not damaged. • If the error continues, replace the Trailing Cable.

• Code: 11A0
• Description: EEPROM I/O Error
  The read/write of the EEPROM on the Main PCA was diagnosed and an error was detected.
• Remedy: • Replace the Main PCA.