Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi HP DesignJet L26500 — Trang 13/16

Code: 54:10

Description: Problem with the Media lever sensor. Pinch Lever sensor error detected.
Remedy: • Check that the Media Lever Sensor cable is not damaged and is correctly connected to the Interconnect PCA. • Replace the Media Lever Sensor .

Code: 55:10

Description: Problem with the Line Sensor
Remedy: • Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power On the Printer. • Perform the Line Sensor service test . • Replace the Line Sensor . • If the System Error continues, replace the Carriage PCA .

Code: 56:10

Description: Analog encoder calibration has failed. Analog Encoder calibration failed. There is a problem with the Drive Roller Encoder/sensor
Remedy: • Replace the Encoder Disc and Sensor .

Code: 58:10

Description: Problem with the Color Sensor
Remedy: • Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power On the Printer. • Check that the Printer has the latest Firmware version, if not, update the firmware to the latest version. • Perform the 1.6.1 Color Sensor test . • If the error is displayed during the printerfs initialization, perform the g6.2 Color Sensor service testh . • If the error is displayed after the printer has initialized, for example when performing a Color Calibration/Linearization, perform the 5.6.3. Open/Close SOLËPage 223. • If the Color Sensor Shutter opens and closes, but the error is still displayed, replace Color Sensor Assembly . • If the Color Sensor Shutter does not open or close, replace the Color Sensor Actuator Assembly ËPage 492. • If the color sensor activator does not elevate or is broken, replace the Color Sensor Actuator Assembly ËPage 492. • If the test is unable to find a good position to open the shutter: • Replace the Color Sensor ËPage 488. • Replace the Encoder Strip ËPage 399. • If the System Error continues, replace the Carriage PCA .

Code: 61:01

Description: Problem with the format of the file. The file format is incorrect and the Printer cannot process the job. This error is mostly seen when a customer is attempting to print a job from a RIP with an unsupported raster format. The most common cause of this error when the customer does not use the correct printer driver for the RIP being used.
Remedy: • Check that the Printer has the latest Firmware version, if not, update the firmware to the latest version. • Check if the RIP supports the printer and that the printer driver is installed in the RIP. • Check that the RIP version is the latest available.

Code: 61:08.01

Description: Job is password protected. The file cannot be printed because it is password protected.
Remedy: Resend the file without password protection.

Code: 61:09

Description: Communication with the RIP broken. There is a problem with the communication between the RIP and the Printer. The job cannot be printed, so it is canceled to save media.
Remedy: • Check the connection of the LAN cable from the Printer and from the computer with the RIP application. • Check to see if there is any error message from the RIP application.

Code: 63:04

Description: Network problem. Input/Output problem through the Network Connector.
Remedy: • Check that the network cable is correctly connected to the network connector. • Check that the Printer has the latest Firmware version, if not, update the firmware to the latest version. • If the System Error continues, replace the Main PCA .
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie