• Code: 0208-342.56
• Description: Tray 4 lift-up failure
  Separator/pass-through motor PWM underflow (motor overspeed)
• Causes: • PF control board (PFCB) • Separator roll assembly
• Remedy: 1 Remove the option tray insert. 2 Check the separator roll assembly gear under the tray base for the following: • Gear tooth breakage • Freedom of rotation Replace the tray if any abnormality is found. 3 Check the cable J10 on PFCB. 4 Check the separator roll assembly for wear or damage. Replace the separator roll assembly if any abnormality is found.

• Code: 0208-344.57
• Description: Tray 4 lift-up failure
  ACM motor no first encoder
• Causes: • PF control board (PFCB) • Tray present sensor (PS35) • ACM assembly
• Remedy: 1 Check the cable J11 on the PFCB. Reseat the cable if any abnormality is found.y is found. 2 Remove the option tray insert and bypass PS35. 3 Enter the Service Mode and conduct a Paper Passage Test: Select [Service Mode] -> [State Confirmation] -> [Paper Passage Test] -> [Tray 4], and press the Start key. 4 Check the ACM for proper operation. Replace the ACM assembly if any abnormality is found. 5 Check the ACM gear for any wear or damage. Replace the ACM assembly if any abnormality is found

• Code: 0208-344.58
• Description: Tray 4 lift-up failure
  ACM motor stop error
• Causes: • PF control board (PFCB) • Tray present sensor (PS35) • ACM assembly
• Remedy: 1 Check the cable J11 on the PFCB. Reseat the cable if any abnormality is found.y is found. 2 Remove the option tray insert and bypass PS35. 3 Enter the Service Mode and conduct a Paper Passage Test: Select [Service Mode] -> [State Confirmation] -> [Paper Passage Test] -> [Tray 4], and press the Start key. 4 Check the ACM for proper operation. Replace the ACM assembly if any abnormality is found. 5 Check the ACM gear for any wear or damage. Replace the ACM assembly if any abnormality is found

• Code: 0208-344.59
• Description: Tray 4 lift-up failure
  ACM motor PWM underflow (motor overspeed)
• Causes: • PF control board (PFCB) • Tray present sensor (PS35) • ACM assembly
• Remedy: 1 Check the cable J11 on the PFCB. Reseat the cable if any abnormality is found.y is found. 2 Remove the option tray insert and bypass PS35. 3 Enter the Service Mode and conduct a Paper Passage Test: Select [Service Mode] -> [State Confirmation] -> [Paper Passage Test] -> [Tray 4], and press the Start key. 4 Check the ACM for proper operation. Replace the ACM assembly if any abnormality is found. 5 Check the ACM gear for any wear or damage. Replace the ACM assembly if any abnormality is found

• Code: 0208-345.60
• Description: Tray 4 lift-up failure
  Hardware error - Board ID unknown
• Causes: • PF control board (PFCB) • Controller board (CTLB)
• Remedy: 1 Check all connections to PFCB. Reseat the cables if any abnormality is found. 2 Check printer’s firmware level. Rewrite the firmware if any abnormality is found. 3 Replace the tray 4. 4 Replace CTLB.

• Code: 0208-345.61
• Description: Tray 4 lift-up failure
  Hardware error - Option type unknown
• Causes: • PF control board (PFCB) • Controller board (CTLB)
• Remedy: 1 Check all connections to PFCB. Reseat the cables if any abnormality is found. 2 Check printer’s firmware level. Rewrite the firmware if any abnormality is found. 3 Replace the tray 4. 4 Replace CTLB.

• Code: 0208-345.62
• Description: Tray 4 lift-up failure
  Hardware error - Product ID unknown
• Causes: • PF control board (PFCB) • Controller board (CTLB)
• Remedy: 1 Check all connections to PFCB. Reseat the cables if any abnormality is found. 2 Check printer’s firmware level. Rewrite the firmware if any abnormality is found. 3 Replace the tray 4. 4 Replace CTLB.

• Code: 0208-345.63
• Description: Tray 4 lift-up failure
  Hardware error - Sensors are not plugged on the board
• Causes: • PF control board (PFCB) • Controller board (CTLB)
• Remedy: 1 Check all connections to PFCB. Reseat the cables if any abnormality is found. 2 Check printer’s firmware level. Rewrite the firmware if any abnormality is found. 3 Replace the tray 4. 4 Replace CTLB.