• Code: C0108
• Description: Tray 4 paper feed motor turning at abnormal timing (When PC-214 is installed) • The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. • The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary.
• Causes: • Tray 4 paper feed motor (M121) • PC control board (PCCB)
• Remedy: 1. Check the connector between M121-PCCB CN9C for proper connection and correct as necessary. 2. Check the connector of M121 for proper drive coupling and correct as necessary. 3. M121 operation check 1. Control signal: PCCB CN9C-5 (CW/CCW) 2. Location of electrical component: PC-214 6-K 4. Replace M121. 5. Replace PCCB. NOTICE • Link to the wiring diagram (N.2.3 PC-214) • Link to the layout drawings for related parts by each trouble code (S.4. C0108)

• Code: C0109
• Description: Tray 4 vertical transport motor turning at abnormal timing (When PC-214 is installed) • The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. • The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary.
• Causes: • Tray 4 vertical transport motor (M122) • PC control board (PCCB)
• Remedy: 1. Check the connector between M122-PCCB CN9C for proper connection and correct as necessary. 2. Check the connector of M122 for proper drive coupling and correct as necessary. 3. M122 operation check • Control signal: PCCB CN9C-13 (CW/CCW) • Location of electrical component: PC-214 6-K 4. Replace M122. 5. Replace PCCB. NOTICE • Link to the wiring diagram (N.2.3 PC-214) • Link to the layout drawings for related parts by each trouble code (S.5. C0109)

• Code: C0202
• Description: Tray 1 feeder up/down abnormality. The tray 1 upper limit sensor (PS25) is not turned ON (blocked) even after the set period of time has elapsed after the paper lift-up operation for the drawer began.
• Causes: • Tray 1 lift-up motor (M12) • Tray 1 upper limit sensor (PS25) • MFP board (MFPB)
• Remedy: 1. Remove the tray and check to see if a piece of paper is not left inside the machine. 2. Check the connector between M12-MFPB CN7E for proper connection and correct as necessary. 3. Check the connector of M12 for proper drive coupling and correct as necessary. 4. Check the connector between PS25-relay CN53-MFPB CN5E for proper connection and correct as necessary. 5. PS25 I/O check, sensor check • Control signal: MFPB CN5E<A>-9 (ON) • Location of electrical component: 9-C 6. M12 operation check • Control signal:MFPB CN7E<A>-11 to 12 • Location of electrical component: 24-C 7. Replace M12. 8. MFPB F13E conduction check 9. Replace MFPB. NOTICE • Link to the wiring diagram (N.1. bizhub C287/C227) • Link to the layout drawings for related parts by each trouble code (S.6. C0202)

• Code: C0204
• Description: Tray 2 feeder up/down abnormality. The tray 2 upper limit sensor (PS22) is not turned ON (blocked) even after the set period of time has elapsed after the paper lift-up operation for the drawer began.
• Causes: • Tray 2 lift-up motor (M13) • Tray 2 upper limit sensor (PS22) • MFP board (MFPB)
• Remedy: 1. Remove the tray and check to see if a piece of paper is not left inside the machine. 2. Check the connector between M13-MFPB CN7E for proper connection and correct as necessary. 3. Check the connector of M13 for proper drive coupling and correct as necessary. 4. Check the connector between PS22-relay CN55-MFPB CN5E for proper connection and correct as necessary. 5. PS22 I/O check, sensor check • Control signal: MFPB CN5E<B>-9 (ON) • Location of electrical component: 11-C 6. M13 operation check • Control signal: MFPB CN7E<A>-13 to 14 • Location of electrical component: 23-C 7. Replace M13. 8. MFPB F13E conduction check 9. Replace MFPB. NOTICE • Link to the wiring diagram (N.1. bizhub C287/C227) • Link to the layout drawings for related parts by each trouble code (S.7. C0204)

• Code: C0206
• Description: Tray 3 lift-up failure (When PC-114 or PC-214 is installed) The tray 3 upper limit sensor (PS116) is not turned ON (blocked) even after the set period of time has elapsed after the paper lift-up operation for the drawer began.
• Causes: • Tray 3 lift-up motor (M113) • Tray 3 upper limit sensor (PS116) • PC control board (PCCB) • MFP board (MFPB)
• Remedy: 1. Remove the tray and check to see if a piece of paper is not left inside the machine. 2. Check the connector between M113-PCCB CN6C for proper connection and correct as necessary. 3. Check the connector of M113 for proper drive coupling and correct as necessary. 4. Check the connector between PS116-relay CN24-PCCB CN4 for proper connection and correct as necessary. 5. PS116 I/O check, sensor check • Control signal: PCCB CN4-3 (ON) • Location of electrical component: PC-114/PC-214 7-C 6. M113 operation check • Control signal: PCCB CN6C-8 to 9 • Location of electrical component: PC-114/PC-214 2-C 7. Replace M113. 8. Replace PCCB. 9. MFPB F11E conduction check 10. Replace MFPB. NOTICE • Link to the wiring diagram (N.2.2 PC-114) • Link to the wiring diagram (N.2.3 PC-214) • Link to the layout drawings for related parts by each trouble code (S.8. C0206)

• Code: C0208
• Description: Tray 4 lift-up failure (When PC-214 is installed) The tray 4 upper limit sensor (PS126) is not turned ON (blocked) even after the set period of time has elapsed after the paper lift-up operation for the drawer began.
• Causes: • Tray 4 lift-up motor (M123) • Tray 4 upper limit sensor (PS126) • PC control board (PCCB) • MFP board (MFPB)
• Remedy: 1. Remove the tray and check to see if a piece of paper is not left inside the machine. 2. Check the connector between M123-PCCB CN8C for proper connection and correct as necessary. 3. Check the connector of M123 for proper drive coupling and correct as necessary. 4. Check the connector between PS126-relay CN47-PCCB CN7C for proper connection and correct as necessary. 5. PS126 I/O check, sensor check • Control signal: PCCB CN7C-3 (ON) • Location of electrical component: PC-214 8-K 6. M123 operation check • Control signal: PCCB CN8C-8 to 9 • Location of electrical component: PC-214 5-K 7. Replace M123. 8. Replace PCCB. 9. MFPB F11E conduction check 10. Replace MFPB. NOTICE • Link to the wiring diagram (N.2.3 PC-214) • Link to the layout drawings for related parts by each trouble code (S.9. C0208)

• Code: C0210
• Description: LCT lift failure (When PC-414 is installed) • The main tray upper limit sensor (PS136) is not turned ON (blocked) even after the set period of time has elapsed after the paper lift-up operation for the drawer began. • The shifter stop / lower limit position sensor (PS138) is not turned OFF (unblocked) even after the set period of time has elapsed after the paper lift-up operation for the drawer began. • The main tray upper limit sensor (PS136) is not turned ON (blocked) even after the set period of time has elapsed after the paper lift-up operating. • The main tray upper limit sensor (PS136) is not turned OFF (unblocked) even after the set period of time has elapsed after the paper lift-down operation began. • The shifter stop / lower limit position sensor (PS138) is not turned ON (blocked) even after the set period of time has elapsed after the paper lift-down operation began.
• Causes: • Main tray upper limit sensor (PS136) • Shifter stop / lower limit position sensor (PS138) • Elevator motor (M134) • PC control board (PCCB) • MFP board (MFPB)
• Remedy: 1. Remove the tray and check to see if a piece of paper is not left inside the machine. 2. Check the connector between M134-PCCB CN10L for proper connection and correct as necessary. 3. Check the connector of M134 for proper drive coupling and correct as necessary. 4. Check the connector between PS136-relay CN1-PCCB CN4 for proper connection and correct as necessary. 5. Check the connector between PS138-relay CN16-PCCB CN14L for proper connection and correct as necessary. 6. PS136 I/O check, sensor check • Control signal: PCCB CN4-3 (ON) • Location of electrical component: PC-414 8-J 7. PS138 I/O check, sensor check • Control signal: PCCB CN14L-6 (ON) • Location of electrical component: PC-414 3-J 8. M134 operation check • Control signal: PCCB CN10L-1 to 2 • Location of electrical component: PC-414 6-J 9. Replace M134. 10. Replace PCCB. 11. MFPB F11E conduction check 12. Replace MFPB. NOTICE • Link to the wiring diagram (N.2.4 PC-414) • Link to the layout drawings for related parts by each trouble code (S.10. C0210)

• Code: C0211
• Description: Manual feed up/down abnormality. • Paper is not turned OFF (unblock) the bypass lift-up position sensor (PS26) even after the transport motor (M1) rotates for a given period of time after the position is switched from stand by position at lift-up plate to the feed position. • The bypass lift-up position sensor (PS26) is not turned ON (blocked) even after the transport motor (M1) rotates for a given period of time after the position is switched from stand by position at lift-up plate to the feed position.
• Causes: • Transport motor (M1) • Bypass pick-up solenoid (SD1) • Bypass lift-up position sensor (PS26) • MFP board (MFPB)
• Remedy: 1. Check the connector between M1-MFPB CN11E for proper connection and correct as necessary. 2. Check the connector of M1 for proper drive coupling and correct as necessary. 3. Check the connector between PS26-relay CN50-MFPB CN30E for proper connection and correct as necessary. 4. Check the connector between SD1-relay CN123-relay CN50-MFPB CN30E for proper connection and correct as necessary. 5. PS26 I/O check, sensor check • Control signal: MFPB CN30E-7 (ON) • Location of electrical component: 13-C 6. SD1 operation check • Control signal: MFPB CN30E-4 (ON) • Location of electrical component: 13-C 7. M1 operation check • Control signal: MFPB CN11E-4 (REM), MFPB CN11E-7 (FGP) • Location of electrical component: 3-C 8. Replace M1. 9. MFPB F12E, F21E conduction check 10. Replace MFPB. NOTICE • Link to the wiring diagram (N.1. bizhub C287/C227) • Link to the layout drawings for related parts by each trouble code (S.11. C0211)