Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Konica-Minolta bizhub Pro 1051 — Trang 75/91

Code: C-4709

Description: Memory time out. • The expansion processing from the memory to the page memory does not terminate. • The compression processing from the page memory to the memory does not terminate. • The development from the memory to the page memory does not terminate. • The transmission of the compressed data from memory to memory does not terminated.
Causes: Overall control board (OACB) Printer control board (PRCB) Image processing board (IPB)
Remedy: 1 Check the connector connection and the wiring on IPB and OACB, and repair it if any abnormality. - 2 Check the connector connection and the wiring on PRCB, and repair it if any abnormality. - 3 Check the connector connection and the wiring between IPB and OACB/between OACB and PRCB, and repair it if any abnormality. - 4 Rewrite the firmware for image control. - 5 Replace IPB. - 6 Replace OACB. - 7 Replace PRCB.

Code: C-4720

Description: Shift amount abnormality while in the repeat. When the shift amount (used for cutting margin, etc.) while in the repeat is negative (-).
Causes: Image processing board (IPB)
Remedy: 1 Check the connector connection and the wiring on IPB, and repair it if any abnormality. - 2 Rewrite the firmware for image control. - 3 Replace IPB.

Code: C-4721

Description: The centering adjustment is too late. The print operation starts before the paper centering adjustment is terminated. (The centering adjustment is too late.)
Causes: Original skew sensor /Fr (PS65) Original skew sensor /Rr (PS66) Printer control board (PRCB) ADU drive board (ADUDB)
Remedy: 1 Check the connector connection and the wiring on IPB and PECB, and repair it if any abnormality. - 2 Check the connector connection and the wiring between ADUCB and the sensor, and repair it if any abnormality. - 3 Check I/O and the operation of the sensor, and repair/replace it if any abnormality. 18-L 4 Replace PS65 or PS66. - 5 Replace PRCB. - 6 Replace ADUDB.

Code: C-4722

Description: The creation of the PWM gamma curve failed. A PWM gamma curve is not created properly.
Causes: Toner control board (TCB) Printer control board (PRCB)
Remedy: 1 Check TCB, and clean it with alcohol if there is IDC sensor dirt or any abnormality. Be sure to clean TCB with alcohol, otherwise replacement of TCB is required. - 2 Check the developing section, and clean/repair it if there is sensor dirt or any abnormality. - 3 Check the connector connection and the wiring between PRCB and TCB, and repair it if any abnormality. - 4 Replace TCB. - 5 Replace PRCB.

Code: C-4725

Description: LPH drive board (LPHB) connection abnormality. Due to the disconnection of the LPHB connector, no connection is available with the overall control board.
Causes: LPH board (LPHB) Relay board /A (RBA) Image processing board (IPB)
Remedy: 1 Check the connector connection and the wiring between LPHB and RBA, and repair it if any abnormality. - 2 Check the connector connection and the wiring between IPB and RBA, and repair it if any abnormality. - 3 Check LPHB, and repair/replace it if any abnormality. 18-C 4 Rewrite the firmware for image control. - 5 Replace LPHB. - 6 Replace RBA. - 7 Replace IPB.

Code: C-4850

Description: Segmentation abnormality. The overall control software accesses an illegal address.
Causes: Image processing board (IPB)
Remedy: 1 Check the connector connection and the wiring on IPB, and repair it if any abnormality. - 2 Rewrite the firmware for image control. - 3 Replace IPB.

Code: C-5010

Description: Communication error between the overall control board (OACB) and the printer control board (PRCB). Any of the following error is detected during data reception between OACB and PRCB. • Data head error • Data check sum error • Undefined command reception error • Occurrence of communication GA error vector
Causes: Printer control board (PRCB) Overall control board (OACB)
Remedy: 1 After turning OFF the sub power switch, turn OFF the main power switch and unplug the power plug. Restart the main body after 10 seconds. - 2 Check the connector connection and the wiring on OACB, and repair it if any abnormality. - 3 Check the connector connection and the wiring on PRCB, and repair it if any abnormality. - 4 Check the connector connection and the wiring between OACB and PRCB, and repair it if any abnormality. - 5 Replace OACB. - 6 Replace PRCB.

Code: C-5101

Description: Fusing motor (M1) speed abnormality. An error detection signal is detected twice in succession within a specified period of time after M1 was turned ON.
Causes: Fusing motor (M1) Printer control board (PRCB)
Remedy: 1 Check the fusing drive section, and repair it if any abnormality. - 2 Check the connector connection and the wiring between PRCB and the motor, and repair it if any abnormality. - 3 Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. 17-K 4 Replace M1. - 5 Replace PRCB.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie