Description: LPH fan /1 (FM3) rotation abnormality. When the print is started, the EM signal of FM3 turns ON.
Causes: LPH fan /1 (FM3) Printer control board (PRCB) AC drive board (ACDB)
Remedy: 1 Check the connector connection and the wiring between PRCB and the fun, and repair it if any abnormality. - 2 Check the connector connection and the wiring between ACDB and the fun, and repair it if any abnormality. - 3 Rotate the fan by I/O or hand, and repair/replace it if any abnormality. 5-L 4 Replace FM3 - 5 Replace PRCB. - 6 Replace ACDB.
Description: LPH fan /2 (FM25) rotation abnormality. When the print is started, the EM signal of FM25 turns ON.
Causes: LPH fan /2 (FM25) Printer control board (PRCB) AC drive board (ACDB)
Remedy: 1 Check the connector connection and the wiring between PRCB and the fun, and repair it if any abnormality. - 2 Check the connector connection and the wiring between ACDB and the fun, and repair it if any abnormality. - 3 Rotate the fan by I/O or hand, and repair/replace it if any abnormality. 6-L 4 Replace FM25. - 5 Replace PRCB. - 6 Replace ACDB.
Description: LPH fan /3 (FM26) rotation abnormality. When the print is started, the EM signal of FM26 turns ON.
Causes: LPH fan /3 (FM26) Printer control board (PRCB) AC drive board (ACDB)
Remedy: 1 Check the connector connection and the wiring between PRCB and the fun, and repair it if any abnormality. - 2 Check the connector connection and the wiring between ACDB and the fun, and repair it if any abnormality. - 3 Rotate the fan by I/O or hand, and repair/replace it if any abnormality. 6-L 4 Replace FM26. - 5 Replace PRCB. - 6 Replace ACDB.
Description: De-curler fan /1 (FM29) rotation abnormality. The EM error detection signal of FM29 is detected twice in succession within a specified period of time after FM29 was turned ON. At this time, the door close is detected.
Causes: de-curler fan /1 (FM29) ADU drive board (ADUDB)
Remedy: 1 Check the connector connection and the wiring between ADUDB and the fan, and repair it if any abnormality. - 2 Rotate the fan by I/O or hand, and repair/replace it if any abnormality. 17-O 3 Replace FM29. - 4 Replace ADUDB. -
Description: De-curler fan /2 (FM30) rotation abnormality. The EM error detection signal of FM30 is detected twice in succession within a specified period of time after FM30 was turned ON. At this time, the door close is detected.
Causes: De-curler fan /2 (FM30) ADU drive board (ADUDB)
Remedy: 1 Check the connector connection and the wiring between ADUDB and the fan, and repair it if any abnormality. - 2 Rotate the fan by I/O or hand, and repair/replace it if any abnormality. 18-O 3 Replace FM30. - 4 Replace ADUDB.
Description: Transfer belt cleaning fan (FM27) rotation abnormality. When the print is started, the EM signal of FM27 turns ON.
Causes: Transfer belt cleaning fan (FM27) ADU drive board (ADUDB)
Remedy: 1 Check the connector connection and the wiring between ADUDB and the fan, and repair it if any abnormality. - 2 Rotate the fan by I/O or hand, and repair/replace it if any abnormality. - 3 Replace FM27. - 4 Replace ADUDB.
Description: Rotation abnormality of fans equipped in ADU. The EM error signal is detected twice in succession within a specified period of time after ADU cooling fun /2 (FM15), belt cooling fan (FM37) and reverse cooling fan (FM38) was turned ON. At this time, the door close is detected.
Causes: ADU cooling fan /2 (FM15) Belt cooling fan (FM37) Reverse cooling fan (FM38) ADU drive board (ADUDB)
Remedy: 1 Check the connector connection and the wiring between ADUDB and the fan, and repair it if any abnormality. - 2 Rotate the fan by I/O or hand, and repair/replace it if any abnormality. 17-O, 20-O, 21-O 3 Replace FM15. - 3 Replace FM37. - 3 Replace FM38. - 4 Replace ADUDB.
Description: Collection pipe cooling fan (FM34) rotation abnormality + 24V power abnormality. The FM34EM error detection signal is detected twice in succession within a specified period of time after FM34 was turned ON. At this time, an error detection signal (24V cut off) is detected.
Causes: DC power supply /2 (DCPS /2) Printer control board (PRCB)
Remedy: 1 Check the connector connection and the wiring between PRCB and DCPS /2, and repair it if any abnormality. - 2 Replace DCPS /2. - 3 Replace PRCB.
Nhận ưu đãi sớm nhất khi chương trình diễn ra
Đăng ký nhận bản tin
Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này.
Chính sách cookie
Những cookie này là cần thiết để trang web hoạt động đúng cách.
Những cookie này giúp chúng tôi hiểu cách khách truy cập tương tác với trang web.
Những cookie này được sử dụng để cung cấp quảng cáo cá nhân hóa.