• Code: 651-02
• Description: Illegal Remote Service Dial-up (Chat program execution error) An unexpected error occurred when RC Gate dialed up the NRS Center.
• Causes: Software bug
• Remedy: Logging only.

• Code: 652-00
• Description: Remote service ID2 mismatching There was an authentication mismatch between ID2 for @Remote, the controller board, and NVRAM.
• Causes: • Used controller board installed • Used NVRAM installed (such action is not allowed.)
• Remedy: • If this occurs during RC Gate installation: Check the validity of the certificate and the NVRAM, check the machine serial number, write the common certificate, and then begin installation again. • If this occurs after RC Gate installation: Clear the RC Gate install status, check the validity of the certificate and the NVRAM, check the machine serial number, write the common certificate, and then begin installation again.

• Code: 653-00
• Description: Incorrect remote service ID2 ID2 stored in the NVRAM has either of the following problems. • Number of characters is not 17. • Includes a character that cannot be printed. • All spaces • NULL
• Causes: Replace the NVRAM.
• Remedy: Clear the RC Gate install status, write the common certificate, and then begin installation again.

• Code: 664-01
• Description: ASIC – SRAM Communication error • When the machine starts or returns from the energy saver mode, a connection error signal between ASIC and SRAM device is detected.
• Causes: • Defective BiCU
• Remedy: • Cycle the power off/on. • Replace the BiCU.

• Code: 665-05
• Description: Master control signal connection error. When the machine starts or returns from the energy saver mode, a connection error signal between CPU and slave device is detected, or the machine cannot access all I/O IPU-ASICs correctly. SC665-11 through -031: When the machine starts or returns from the energy saver mode, a connection error between CPU and ASIC is detected.
• Causes: 1. Incorrect FFC connection 2. Damaged FFC (disconnection or dust) 3. BiCU failure (Deteriorated board, sticking dust, or damaged parts)
• Remedy: • Cycle the power off/on. • Replace the BiCU.

• Code: 665-06
• Description: IPU/IOB control signal connection error. When the machine starts or returns from the energy saver mode, a connection error signal between CPU and slave device is detected, or the machine cannot access all I/O IPU-ASICs correctly. SC665-11 through -031: When the machine starts or returns from the energy saver mode, a connection error between CPU and ASIC is detected.
• Causes: 1. Incorrect FFC connection 2. Damaged FFC (disconnection or dust) 3. BiCU failure (Deteriorated board, sticking dust, or damaged parts)
• Remedy: • Cycle the power off/on. • Replace the BiCU.

• Code: 665-07
• Description: IPU control signal connection error. When the machine starts or returns from the energy saver mode, a connection error signal between CPU and slave device is detected, or the machine cannot access all I/O IPU-ASICs correctly. SC665-11 through -031: When the machine starts or returns from the energy saver mode, a connection error between CPU and ASIC is detected.
• Causes: 1. Incorrect FFC connection 2. Damaged FFC (disconnection or dust) 3. BiCU failure (Deteriorated board, sticking dust, or damaged parts)
• Remedy: • Cycle the power off/on. • Replace the BiCU.

• Code: 665-11
• Description: ASIC connection error. When the machine starts or returns from the energy saver mode, a connection error signal between CPU and slave device is detected, or the machine cannot access all I/O IPU-ASICs correctly. SC665-11 through -031: When the machine starts or returns from the energy saver mode, a connection error between CPU and ASIC is detected.
• Causes: 1. Incorrect FFC connection 2. Damaged FFC (disconnection or dust) 3. BiCU failure (Deteriorated board, sticking dust, or damaged parts)
• Remedy: • Cycle the power off/on. • Replace the BiCU.