Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh Aficio SP6430DN

Code: SC195-00

Description: Machine serial number error Comparison of the product identification code in the machine serial number (11 digits).
Causes: The product identification code in the machine serial number (11 digits) does not match.
Remedy: Re-enter the machine serial number.

Code: SC230-00

Description: FGATE*1: Does not turn ON. GPIO*2 has not been asserted, although the specified time (200 ms) elapsed after setting JOB to be started and reaching the FGAT assert time.
Causes: Control Board (*1)FGATE: Signals used between the controller and the engine in order to send the information about the sub scan length of the page to be printed. (*2)GPIO: A type of input/output terminal
Remedy: Turn the main power off/on.

Code: SC231-00

Description: FGATE*1: Does not turn OFF. GPIO*2 has not been negated, although the specified time (200 ms) elapsed after detecting GPIO*assert and then reaching the expected FGATE negate time.
Causes: * This is an I/O pin. Such I/O pins can be used for a variety of applications, depending on the setting. (*1)FGATE: Signals used between the controller and the engine in order to send the information about the sub scan length of the page to be printed. (*2)GPIO: A type of input/output terminal
Remedy: • Turn the main power off/on.

Code: SC270-00

Description: Write ASIC communication error • When the engine board could not read the Unique ID of the Writing ASIC properly when starting this machine. • When an Error bit occurred in the communication between the engine board and the Writing ASIC.
Causes: The unique ID of the write ASIC was not read normally.
Remedy: • Turn the main power off/on.

Code: SC277-00

Description: LEDA communication error The head type data was read three times in succession
Causes: • Defective LEDA • Defective FFC for LEDA • Defective the engine board (Defective interface b/w Write ASIC - LEDA)
Remedy: • Turn the main power off/on.

Code: SC277-10

Description: LEDA communication error: other The head type data was read three times in succession
Causes: • Defective engine board (LEDA Power Error: Broken FU7) • Defective harness between PSU – engine board • PSU fault (5V Fuse broken) • Defective controller (Defective engine interface)
Remedy: • Turn the main power off/on.

Code: SC302-00

Description: High voltage output error: Charge unit /Development unit This SC is issued if the engine board detects a short in the power pack 10 times consecutively.
Causes: Open circuit (+) / Short circuit (-)
Remedy: • Turn the main power off/on. • Replace the board. • Check the connector connection.

Code: SC332-00

Description: Toner supply transfer lock This SC is issued if the error that the toner is not supplied is detected n times consecutively (n: SP2-931-005) on the condition that the toner cartridge is not in end
Causes: • Overload on the toner transferring part (clogging of toner) • Screw for detecting PCDU does not turn • Detector element (sensor) defective: light leak • Supplying pick does not engage • Defective Supplying clutch • Defective Drive mechanism of screw for supplying toner cartridge
Remedy: • Turn the main power off/on.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie