Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh Aficio SPC730DN — Trang 7/15

Code: 542-03

Description: Fusing lamp (Center) thermopile not reloaded 2
The heater (Center) thermistor does not reach the reload temperature 44 seconds after the start of motor rotation.
Causes: • Stained thermopile lens • Deformed or floating thermistor • Input voltage out of range • The overtemperature prevention mechanism started working
Remedy: • Clear the SP: fusing SC. • Clean the thermopile lens. • Replace the thermopile.

Code: 542-04

Description: Fusing lamp (Center) thermopile not reloaded 3
The heater (Center) thermistor does not reach 100 deg C 5.5 seconds after the start of heat control (during low-temperature start up control).
Causes: • Stained thermopile lens • Deformed or floating thermistor • Input voltage out of range • The overtemperature prevention mechanism started working
Remedy: • Clear the SP: fusing SC. • Clean the thermopile lens. • Replace the thermopile.

Code: 543-00

Description: Fusing (Center) thermopile high-temperature detected (software)
The temperature is detected to stay at 230 deg C or higher for one second.
Causes: • Shorted triac • Failed Engine Board
Remedy: • Clear the SP: fusing SC. • Replace the PSU. • Replace the Engine Board.

Code: 544-00

Description: Fusing (Center) thermopile high-temperature detected (hardware)
The hardware high-temperature error Sensor flag is detected at 10 ms intervals.
Causes: • Damaged triac (shorted) • Failed engine control board • Failed fusing thermopile • Failed fusing thermistor • Abnormal fusing control software behavior • The PWM signal is continuously supplied from the IH inverter (due to a software or temperature Sensor error).
Remedy: • Clear the SP: fusing SC. • Replace the PSU. • Replace the Engine Board. • Replace the fusing thermopile. • Replace the Fusing Unit.

Code: 545-00

Description: Fusing (Center) heater stay ON
The fusing (Center) heater stays ON for 5.7 seconds or more when in stand-by state (or the fusing roller is not rotating).
Causes: • Deformed or floating thermistor • Broken fusing lamp wire • The overtemperature prevention mechanism started working
Remedy: • Clear the SP: fusing SC. • Clean the thermopile lens. • Replace the fusing thermopile. • Replace the fusing (Center) lamp.

Code: 547-01

Description: Zero-crossing error (adhered relay contact)
When the fusing relay is in an OFF state, a "zero-crossing interrupt request" occurs in 50 ms.
Causes: Damaged fusing relay (adhered contact)
Remedy: • Turn the main power OFF and then ON. • Replace the harness. • Replace the PC board. • Replace the PSU.

Code: 547-02

Description: Zero-crossing error (bad relay contact)
If a "zero-crossing interrupt request" does not occur when the fusing relay is in an ON state, an error results.
Causes: - Damaged fusing relay (open contact) - Failed fusing relay drive circuit - PSU fuse (24VS) blown
Remedy: • Turn the main power OFF and then ON. • Replace the harness. • Replace the Engine Board. • Replace the PSU. • Replace the fuse.

Code: 547-03

Description: Zero-crossing error (low frequency error)
The number of zero-crossing interrupts does not reach a certain value in 500 ms.
Causes: The frequency of the commercial power supply line is unstable.
Remedy: • Turn the main power OFF and then ON. • Check the commercial power supply line. • Replace the harness. • Replace the Engine Board. • Replace the PSU.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie