Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh Aficio SPC730DN — Trang 8/15

Code: 551-00

Description: Broken fusing (End) thermistor wire
At least ten times, the temperature is detected to stay at 0 deg C or less for three seconds.
Causes: - Broken thermistor wire - Bad connector contact
Remedy: • Clear the SP: fusing SC. • Check the connector connection. • Replace the fusing (End) thermistor.

Code: 552-02

Description: Fusing (End) thermistor not reloaded 1
The heating (End) thermistor does not reach 80 deg C 7.7 seconds after the start of heat control (during normal startup control)
Causes: • Stained thermopile lens • Deformed or floating thermistor • Input voltage out of range • The overtemperature prevention mechanism started working
Remedy: • Clear the SP: fusing SC. • Replace the Fusing Unit.

Code: 552-03

Description: Fusing (End) thermistor not reloaded 2
The heating (End) thermistor does not reach 80 deg C 7.7 seconds after the start of heat control (during normal startup control)
Causes: • Stained thermopile lens • Deformed or floating thermistor • Input voltage out of range • The overtemperature prevention mechanism started working
Remedy: • Clear the SP: fusing SC. • Replace the Fusing Unit.

Code: 552-04

Description: Fusing (End) thermistor not reloaded 3
The heating (End) thermistor does not reach 80 deg C 7.7 seconds after the start of heat control (during normal startup control)
Causes: • Stained thermopile lens • Deformed or floating thermistor • Input voltage out of range • The overtemperature prevention mechanism started working
Remedy: • Clear the SP: fusing SC. • Replace the Fusing Unit.

Code: 553-00

Description: Fusing (End) thermistor high-temperature detected (software)
The temperature is detected to stay at 230 deg C or higher for one second.
Causes: • Shorted triac • Failed Engine Board
Remedy: • Clear the SP: fusing SC. • Replace the PSU. • Replace the Engine Board.

Code: 554-00

Description: Fusing (End) thermistor high-temperature detected (software)
The hardware high-temperature error Sensor flag is detected at 10 ms intervals.
Causes: • Damaged triac (shorted) • Failed engine control board • Failed fusing thermopile • Failed fusing thermistor • Abnormal fusing control software behavior • The PWM signal is continuously supplied from the IH inverter (due to a software or temperature Sensor error).
Remedy: • Clear the SP: fusing SC. • Replace the PSU. • Replace the Engine Board. • Replace the fusing thermopile. • Replace the Fusing Unit.

Code: 555-00

Description: Fusing (End) heater stay ON
The fusing (End) heater stays ON for 8.6 seconds or more when in stand-by state (or the fusing roller is not rotating).
Causes: • Deformed or floating thermistor • Broken fusing lamp wire • The overtemperature prevention mechanism started working
Remedy: • CLEAR THE SP: FUSING SC. • Replace the thermistor. • Replace the fusing (End) lamp.

Code: 557-00

Description: Zero-crossing frequency exceeded
The number of zero-crossing interrupts exceeds a certain value in 500 ms.
Causes: The frequency of the commercial power supply line is unstable or noise occurs
Remedy:
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie