Description: Load Tray/Tray Empty No paper detected in tray.
Causes: Left Side Harness Assy (PL3.1.18) Photo Sensor (PL3.2.13) Paper Feeder (PL3.1.3) MCU Board (PL8.2.13)
Remedy: 1 Check the paper for loading and setting Check that the paper in use meets the print job requirements Does the error still occur after reloading the paper and changing the paper settings that the print job requires? Go to step 2. Complete 2 Check the No Paper Actuator for shape and operation Pull the paper tray out. Are the shape and operation of the No Paper Actuator normal? Go to step 3. Reseat the No Paper Actuator. If broken or deformed, replace the Feeder Assembly. 3 Check the Tray No Paper Sensor (Photo Sensor) for operation Pull the CASSETTE ASSY 250 out. Perform the Tray No Paper test: Service Mode > Engine Diag > Sensor Test > Tray No Paper Does the number on the screen increase by one, when the actuator of the Tray No Paper Sensor (Photo Sensor) is operated? Replace the MCU Board. Go to step 4. 4 Check the connectors of the Tray No Paper Sensor (Photo Sensor) for connection Check the connections between the MCU Board and Photo Sensor. Are P/J23 and P/J234 connected correctly? Go to step 5. Reconnect the connector(s) P/ J23 and/or P/ J234 correctly. 5 Check the Left Side Harness Assy for continuity Disconnect J23 from the MCU Board. Disconnect J234 from the Photo Sensor. Is each cable of J23 <=> J234 continuous? Go to step 6. Replace the Feeder Assy or Left Side Harness Assy. 6 Check the power to the Tray No Paper Sensor (Photo Sensor) Disconnect J23 from the MCU Board. Is the voltage across P23-9pin <=> ground on the MCU Board, about +3.3 VDC? Go to step 7. Replace the MCU Board. 7 Check the Tray No Paper Sensor (Photo Sensor) for operation Check the voltage across J23-11pin <=> ground on the MCU Board. Does the voltage change, when the Tray No Paper Sensor actuator is operated? Replace the MCU Board. Replace the Photo Sensor.
Code: -10
Description: Front Cover Open The Front Cover is open.
Remedy: 1 Is the Front Cover damaged? Replace the Front Cover. Go to step 2. 2 Check the Interlock Switch for operation. Perform the Cover Open Sensor test: Service Mode > Engine Diag > Sensor Test > Cover Open Sensor. Does the Switch operate properly? Replace the MCU Board. Go to step 3. 3 Measure the voltage a P44-1 <=> ground. Does the voltage measure +24 VDC? Go to step 4. Replace the LVPS. 4 Replace the Interlock Switch Harness. Does the error still occur? Replace the MCU Board. Complete.
Code: -11
Description: Side Door Open The Side Door (Toner Access Door) is open.
Remedy: 1 Is the Toner Access Door damaged? Replace the Toner Access Door. Go to step 2. 2 Open and close the Toner Access Door. Is the door latched correctly? Go to step 3. Reseat or replace the Toner Access Door. 3 Check the Side R Switch (SWITCH) for operation Perform the Side Switch test: Service Mode > Engine Diag > Sensor Test > Side Switch. Does the number on the screen increase by one when the Toner Access Door is closed and opened? Replace the MCU Board. Go to step 4. 4 Check the Side Switch Harness for continuity 1. Disconnect J29 from the MCU Board. 2. Disconnect J291 from the Side Switch. Is each cable of J29 <=> J291 continuous? Replace the Switch (R Side Door) then go to step 5. Replace the Harn Assy Side SW. 5 Does the error still occur when the power is turned OFF and ON? Replace the MCU Board. Complete
Code: 010-317
Description: Insert Fuser The printer detects that the Fuser is not installed.
Remedy: 1 Reseat the Fuser. Warning: Start the operation after the Fuser has cooled down. Does the error still occur when the power is turned OFF and ON? Go to step 2. Complete 2 Check the connectors for connection Remove the Fuser. Warning: Start the operation after the Fuser has cooled down. Check the connections between the MCU Board and Fuser. Are P/J17 and P/J171 connected correctly? Go to step 4. Reconnect the connector(s) P/ J17 and/or P/ J171 correctly, then go to step 3. 3 Does the error still occur when the power is turned OFF and ON? Go to step 4. Complete 4 Check the Fuser Harness Assy for continuity Remove the Fuser. Warning: Start the operation after the Fuser has cooled down. Disconnect J17 from the MCU Board. Is each cable of J17 <=> P171 continuous? NOTE: P171 is attached to the frame. Go to step 5. Replace the Fuser Harness Assy. 5 Check the resistances of Temp. Sensor in the Fuser Remove the Fuser. Warning: Start the operation after the Fuser has cooled down. Check the resistances across the following pins of the removed Fuser. J171-5 <=> J171-4 J171-6 <=> J171-8 J171-6 <=> J171-7 Can the resistances be measured? (The resistances are 7 k-ohm at 180 degrees C). Replace the MCU Board Replace the Fuser. After replacing the Fuser, be sure to reset the life counter value.
Code: 010-351
Description: Replace Fuser / Fuser Life The Fuser has reached end of life.
Causes: Fuser (PL6.1.1) MCU Board (PL8.2.13)
Remedy: 1 Check the life counter value of the Fuser Does the life counter value show the near of the end? Replace the Fuser. After replacing the Fuser, be sure to reset the life counter value. Go to step 2. 2 Check after reseating the Fuser Reseat the Fuser. Warning: Start the operation after the Fuser has cooled down. Does the error still occur when the power is turned OFF and ON? Go to step 3. Complete 3 Check after replacing the Fuser Replace the Fuser. Warning: Start the operation after the Fuser has cooled down. Does the error still occur when the power is turned OFF and ON? NOTE: After replacement, be sure to clear the life counter value. Replace the MCU Board. Complete
Remedy: 1 Does the error still occur when the power is turned OFF and ON? Go to step 2. Complete 2 Check after reseating the Fuser Reseat the Fuser. Warning: Start the operation after the Fuser has cooled down. Does the error still occur when the power is turned OFF and ON? Go to step 3. Complete 3 Check the connectors for connection Remove the Fuser. Warning: Start the operation after the Fuser has cooled down. Check the connections between the MCU Board (P/J17) and Fuser (P/ J171). Check the connections between the Fuser (P/J171) and LVPS Board (P/ J47). Check the connections between the LVPS Board (P/J501 and P/J502) and MCU Board (P/J14 and P/J15). Are these connectors connected correctly? Go to step 5. Reconnect the connector(s) P/ J17, P/J47, P/ J171, P/J501, P/ J502, P/J14 and/or P/J15 correctly, then go to step 4." 4 Does the error still occur when the power is turned OFF and ON? Go to step 5. Complete 5 Check the Fuser Harness Assy for continuity Disconnect J17 from the MCU Board. Disconnect J47 from the LVPS Board. Is each cable of J17 and J47 <=> P171 continuous? NOTE: P171 is attached to the frame. Go to step 6. Replace the Fuser Harness Assy. 6 Check the LVPS Harness Assy for continuity Disconnect J14 from the MCU Board. Disconnect J501 from the LVPS Board. Is each cable of J14 <=> J501 continuous? Go to step 7. Replace the LVPS Harness Assy. 7 Check after replacing the Fuser Replace the Fuser. Warning: Start the operation after the Fuser has cooled down. Does the error still occur when the power is turned OFF and ON? NOTE: After replacement, be sure to clear the life counter value. Go to step 8. Complete 8 Check after replacing the LVPS Board Replace the LVPS Board. Complete
Code: 016-500, 016-501, 016-502
Description: Flash Memory Errors • Chain Link 016-500: Erase Flash Error • Chain Link 016-501: Write Flash Error • Chain Link 016-502: Verify Flash Error
Causes: • Image Processor Board, PL8.1.9
Remedy: 1 Check the download file Was the correct file downloaded? Go to step 2. Re-download the correct file. 2 Check the connection between PC and printer Are the PC and the printer correctly connected by USB or LAN? Go to step 4. Go to step 3. 3 Disconnect and reconnect the USB or network cable. Does the error still occur when the power is turned OFF and ON? Go to step 4. Complete 4 Reseat plugs and jacks on the Image Processor Board (refer to the procedure on page 8-60). Does the error still occur when the power is turned OFF and ON? Go to step 4. Complete 5 Re-download the correct file from the Xerox web site. Does the error still occur when the power is turned OFF and ON? Replace the Image Processor Board. Complete
Code: 016-718
Description: Out of Memory The printer memory is full and cannot continue to print. Print job requires additional memory.
Remedy: 1 1. Check the required memory for the print job. 2. Print a small size file (like a Windows test print). 3. Does the error still occur? Go to step 2. Add memory card or separate the print job. 2 Reseat the memory card. Does the error still occur? Go to step 3. Complete. 3 Check the memory card capacity. Print the printer Configuration Page: Menu > Information Pgs > Configuration. Is the memory capacity correct, including the optional memory? Go to step 4. Replace the Image Processor Board. 4 Replace the memory card. Does the error still occur? Replace the Image Processor Board.
Máy Photocopy
Máy in mã vạch - In tem nhãn
PC- Laptop - Điện thoại
Máy in – Mực in
Máy chiếu - Màn chiếu
Máy chấm công - Kiểm soát ra vào
Máy hủy tài liệu
Máy đếm tiền, kho , quỹ
Loa - Loa bluetooth, vi tính, Karaok
Máy lạnh, Cây nước nóng lạnh
