Remedy: 1 Reseat the Fuser and cycle system power. Does the error persist? Go to step 2. Complete 2 Check the connections between the MCU Board P/J17 and Fuser P/J171. Are the connectors secure? Go to step 3. Secure the connectors. 3 Check the Fuser harness continuity. 1. Remove the Fuser. 2. Disconnect J17 from the MCU Board. Is the harness damaged? NOTE P171 is attached to the frame. Repair the harness. Go to step 4. 4 Check Fuser temperature sensor resistance. 1. Remove the Fuser. 2. Check resistance across these Fuser pins: • J171-5pin <=> J171-4pin • J171-6pin <=> J171-8pin • J171-6pin <=> J171-7pin Is there measurable resistance? (Resistance is 7 K Ohm at 180 degrees C). Replace the MCU Board. Replace the Fuser.
Description: Replace Fuser. The count value indicates the Fuser is near or has reached end of life.
Causes: • Fuser, PL6.1.1 • MCU Board, PL8.2.13
Remedy: 1 Reseat the Fuser and cycle system power. Does the error persist? Go to step 2. Complete 2 Check the connections between the MCU Board P/J17 and Fuser P/J171. Are the connectors secure? Go to step 3. Secure the connectors. 3 Replace the Fuser. Does the error persist? Replace the MCU Board. Complete
Remedy: 1 Reseat the Fuser and cycle system power. Does the error persist? Go to step 2. Complete 2 Check these connections • MCU Board P/J17 and Fuser P/J171. • Fuser P/J171 and LVPS P/J47. • LVPS P/J501 and P/J502 and MCU Board P/J14 and P/J15 Are the connectors secure? Go to step 3. Secure the connectors. 3 Check the Fuser harness continuity. 1. Remove the Fuser. 2. Disconnect J17 from the MCU Board and J47 from the LVPS. Is the harness damaged? NOTE P171 is attached to the frame. Repair the harness. Go to step 4. 4 Check the LVPS harness continuity. Disconnect J14 from the MCU Board and J501 from the LVPS. Is the harness damaged? Repair the harness. Go to step 5. 5 Replace the Fuser. Does the error persist? Replace the MCU Board. Comple
Description: Firmware Errors The firmware download to the printer failed. • 016-500: Erase Flash Error • 016-501: Write Flash Error • 016-502: Verify Flash Error
Causes: • Image Processor Board, PL8.1.7
Remedy: 1 Check the system firmware version. Is the downloaded system firmware the correct version? Go to step 2. Download the correct firmware file. 2 Check the network or USB connection, then cycle system power. Does the error persist? Go to step 3. Complete. 3 Reseat connections on the Image Processor Board, then cycle system power. Does the error persist? Replace the Image Processor Board. Complete.
Description: Out of Memory 016-718 The printer has detected a memory access error.
Causes: • Image Processor Board, PL8.1.7
Remedy: 1 Check the memory. Print the Configuration page to determine the amount of memory installed. Is the print job too large? Divide the print job to fit installed memory. Go to step 2. 2 Reseat the Memory Card if installed. Does the error persist? Replace the Memory Card, then go to step 3. Complete. 3 Reseat all connections on the Image Processor Board. Does the error persist? Replace the Image Processor Board. Complete.
Description: PDL Error 016-720 The printer has detected a print job error.
Causes: • Image Processor Board, PL8.1.7
Remedy: 1 Print a small file (test print). Does the error persist? Go to step 2. Divide the print job to fit installed memory. 2 Reseat all connections on the Image Processor Board. Does the error persist? Replace the Image Processor Board. Complete.
Description: Format Error 016-737 The system firmware file is corrupt or communications to the printer failed.
Causes: • Image Processor Board, PL8.1.7
Remedy: 1 Check the system firmware version. Is the downloaded system firmware the correct version? Go to step 2. Download the correct firmware file. 2 Check the network or USB connection, then cycle system power. Does the error persist? Go to step 3. Complete. 3 Reseat connections on the Image Processor Board, then cycle system power. Does the error persist? Replace the Image Processor Board. Complete.
Description: Firmware Errors The firmware download to the printer failed. • 016-741: Protection Error • 016-742: Invalid ID Error • 016-743: Range Check Error • 016-744: Check Sum Error • 016-745: Header Error
Causes: • Image Processor Board, PL8.1.7
Remedy: 1 Check the system firmware version. Is the downloaded system firmware the correct version? Go to step 2. Download the correct firmware file. 2 Check the network or USB connection, then cycle system power. Does the error persist? Go to step 3. Complete. 3 Reseat connections on the Image Processor Board, then cycle system power. Does the error persist? Replace the Image Processor Board. Complete.
Nhận ưu đãi sớm nhất khi chương trình diễn ra
Đăng ký nhận bản tin
Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này.
Chính sách cookie
Những cookie này là cần thiết để trang web hoạt động đúng cách.
Những cookie này giúp chúng tôi hiểu cách khách truy cập tương tác với trang web.
Những cookie này được sử dụng để cung cấp quảng cáo cá nhân hóa.