Remedy: 1 Check the Optional Feeder installation. Is the Optional Feeder installed correctly? Go to step 2. Reseat the printer on the feeder. 2 Check the connection between the printer and feeder (P/J273). Is the connector damaged? Repair or replace the harness. Go to step 3. 3 Check the Tray Harness continuity. Disconnect P/J419 from the Feeder Board and P/J273 from the Option Harness. Is the harness damaged? Repair or replace the harness. Go to step 4. 4 Check the Option Harness continuity. Disconnect P/J27 from the MCU Board and P/J273 from the Tray Harness. Is the harness damaged? Repair or replace the harness. Go to step 5. 5 Replace the Feeder Board. Does the error persist? Go to step 6. Complete 6 Replace the Optional Feeder. Does the error persist? Replace the MCU Board. Complete
Remedy: 1 Check the Optional Feeder installation. Is the Optional Feeder installed correctly? Go to step 2. Reseat the printer on the feeder. 2 Check the Feed and Separator Roller rotation. Do the rollers rotate smoothly? Go to step 3. Replace the rollers. 3 Check P/J422 on the Feeder Board and P/J211 on the Feed Motor. Are and connected secure? Go to step 4. Secure the connections. 4 Test the Option Feeder Motor: Engine Diag > Motor Test > Tray2 Feeder Motor. Does the Feed Motor rotate? Replace the MCU Board. Go to step 5. 5 Check the Tray Motor Harness continuity. Disconnect P/J422 on the Feeder Board and P/J211 on the Feed Motor. Is the harness damaged? Repair or replace the harness. Go to step 6. 6 Check power to the Feed Motor. Disconnect P/J422 on the Feeder Board. Is there +24V across ground <=> J422-6 when the Interlock Switch is closed? Replace the Option Feed Motor Kit. Go to step 7. 7 Check connections between the Feeder and MCU boards. Are P/J419, P/J273 and P/J27 secure Go to step 8. Secure the connections. 8 Check the Tray Harness continuity. Disconnect P/J419 from the Feeder Board and P/J273 from the Option Harness. Is the harness damaged? Repair or replace the harness. Go to step 9. 9 Check the Option Harness continuity. Disconnect P/J273 from the Option Harness P/J27 from the MCU Board. Is the harness damaged? Repair or replace the harness. Go to step 10. 10 Check power to the Feeder Board. Disconnect P/J27 on the MCU Board. Is there +24V across ground <=> J27-A5 and J27-A6 on the MCU Board when the Interlock Switch closed. Replace the Feeder Board. Replace the MCU Board.
Remedy: 1 Check the Duplex Unit installation. Is the Duplex Unit installed correctly? Go to step 2. Reseat the Duplex Unit. 2 Check the connections between the Duplex and MCU boards. Are P/J27, P/J271, P/J272 and P/J 601 connected secure? Go to step 3. Secure the connections. 3 Check the Duplex Harness continuity. Disconnect P/J601 from the Duplex Board and P/J272 from the Duplex Harness. Is the harness damaged? Repair or replace the harness. Go to step 4. 4 Check the Duplex Relay Harness continuity Disconnect P/J271 from the Duplex Relay Harness and P/J272 from the Duplex Harness. Is the harness damaged? Repair or replace the harness. Go to step 5. 5 Check the Option Harness continuity. Disconnect P/J272 from the Option Harness and P/J27 from the MCU Board. Is the harness damaged? Repair or replace the harness. Go to step 6. 6 Check power to the Duplex Board. Remove the Duplex Unit. Is there +3.3V across ground <=> J272-7 on the duplex connector when the Interlock Switch closed. Replace the Duplex Board. Replace the MCU Board.
Description: IU CRUM Error 091-916 An error occurred while reading the Imaging Unit CRUM.
Causes: • Imaging Unit PL4.1.21 • MCU Board, PL8.2.13 • Imaging Unit Harness, PL9.1.11
Remedy: 1 Remove the Imaging Unit and check the condition of P/J422. Is the connector damaged on the Imaging Unit or Imaging Unit Harness? Replace the damaged component. Go to step 2. 2 Check the Imaging Unit Harness continuity. Disconnect P/J42 from the MCU Board and P/J422. Is the harness damaged? Repair the harness. Go to step 3. 3 Replace the Imaging Unit. Does the error persist? Replace the MCU Board. Complete.
Description: CTD Sensor Error 092-310 Caution Do not run the toner motors for more than a few seconds. The ADC Sensor has detected a density error for the indicated color.
Causes: • Left Side Harness, PL3.1.18 • Imaging Unit, PL4.1.21 • Dispense Assembly, PL5.1.1 • Toner Cartridges, PL5.1.21~24 • Toner Motor harness, PL5.1.25 • Transfer Belt, PL6.1.7 • MCU Board, PL8.2.13
Remedy: 1 Check the Transfer Belt installation. Is the Transfer Belt correctly installed? Go to step 3. Correct the installation. Go to step 2. 2 Does the error persist? Go to step 3. Complete. 3 Test the Toner Motor: Engine Diag > Motor Test > CMYK Toner Motor for the affected color. Does the motor rotate? Go to step 4. Go to step 5. 4 Check the Dispense Assembly gear for the indicated color. Is the gear damaged or excessively worn? Replace the Dispense Assembly. Go to step 5. 5 Check Left Side Harness continuity. Disconnect P/J28 from the MCU Board and P/J281 to the Transfer Belt. Is the harness damaged? Repair or replace the harness. Go to step 6. 6 Check MCU Board connectors P/J18 and toner motor connections: • P/J181(Y) • P/J182(M) • P/J191(C) • P/J192(K) Are the connectors secure? Go to step 7. Reconnect the connectors. 7 Check Toner Motor harness continuity. Disconnect P/J18 from the MCU Board and the connection to the indicated toner motor. Is the harness damaged? Repair or replace the harness. Go to step 8. 8 Check for +24 V at J18 or J19 on the MCU Board. Is +24 V available at • J18-3 (Y) • J18-8 (M) • J19-4 (C) • J19-9 (K) when the Interlock Switch is closed? Replace the Dispense Assembly. Replace the MCU Board. 9 Replace the indicated Toner Cartridge. Does the error persist? Go to step 10. Complete. 10 Replace the Imaging Unit. Does the error persist? Replace the Transfer Belt. Complete.
Remedy: 1 Check the Humidity Harness continuity. Disconnect J20 from the MCU Board and J201 from the Humidity Sensor. Is the harness damaged? Repair the harness. Go to step 2. 2 Check power to Humidity Sensor. Disconnect J20 from the MCU Board. Is the voltage across P20-4 <=> ground about +5 V? Replace the Humidity Sensor. Replace the MCU Board.
Description: Trans Life Over 094-351 The Transfer Belt has reached end of life.
Causes: • Left Side Harness, PL3.1.18 • Transfer Belt, PL6.1.7 • MCU Board, PL8.2.13
Remedy: 1 Check the Transfer belt life counter. Has the counter reached end of life? Replace the Transfer Belt. Go to step 2. 2 Check the Transfer Belt installation. Is the Transfer Belt correctly installed? Go to step 3. Reseat the Transfer Belt. Go to step 2. 3 Does the error still occur when the printer is turned On? Go to step 4. Complete. 4 Check connectors P/J28 and P/J281 between the MCU Board and Transfer Belt. Are the connectors secure? Go to step 5. Reconnect the connectors. 5 Check Left Side Harness continuity. Disconnect P/J28 from the MCU Board and P/J281 to the Transfer Belt. Is the harness damaged? Repair or replace the harness. Go to step 6. 6 Replace the Transfer Belt. Does the error persist? Replace the MCU Board. Complete.
Remedy: 1 Check the Image Processor Board installation. Is the Image Processor Board correctly installed? Go to step 2. Reseat connections on the IP Board. 2 Does the error still occur when the printer is turned On? Replace the Image Processor Board. Complete.
Nhận ưu đãi sớm nhất khi chương trình diễn ra
Đăng ký nhận bản tin
Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này.
Chính sách cookie
Những cookie này là cần thiết để trang web hoạt động đúng cách.
Những cookie này giúp chúng tôi hiểu cách khách truy cập tương tác với trang web.
Những cookie này được sử dụng để cung cấp quảng cáo cá nhân hóa.