• Code: 05-300
• Description: DADF Jam 3 RAP 05-300 The lead edge of the document failed to actuate the duplex sensor within the correct time in reverse mode.
• Remedy: 1. Raise the DADF input tray, PL 5.10 Item 5. Remove all jammed paper. 2. Check the document path for damage or obstructions. 3. Check the duplex gate, PL 5.25 Item 25 for damage. If necessary, install a new duplex gate. 4. Check that the following components are clean and rotate freely. • Exit roll, PL 5.20 Item 2. • Exit roll idlers, PL 5.20 Item 20. 5. Check that the duplex sensor actuator, PL 5.25 Item 27 moves freely and is not damaged. 6. Enter dC330 code 05-170. Check the duplex sensor (Q05-170). NOTE: The duplex sensor is mounted on the DADF PWB, PL 5.20 Item 6. 7. Enter code 05-220. Check that the DADF duplex motor, PL 5.25 Item 5 runs in the reverse direction and drives the exit roll, PL 5.20 Item 2. 8. Check the wiring between the DADF duplex motor and CN5 on the DADF PWB. 9. Check the exit roll gear, PL 5.20 Item 5 for damage. If necessary, install a new exit roll gear. 10. If necessary, install new components: • DADF PWB, PL 5.20 Item 6. • Duplex motor assembly, PL 5.25 Item 4. • Document transport assembly, PL 5.10 Item 2.

• Code: 05-400
• Description: DADF Jam 4 RAP 05-400 The lead edge or trail edge of the document failed to actuate or deactuate the scan sensor within the correct time in reverse mode.
• Remedy: 1. Open the DADF top cover assembly, PL 5.15 Item 11. Remove all jammed paper. 2. Raise the DADF input tray, PL 5.10 Item 5. Remove all jammed paper. 3. Check the document path for damage or obstructions. 4. Check that the following components are clean and rotate freely. • Duplex roll, PL 5.25 Item 22. • Duplex roll idlers, PL 5.15 Item 28. • Scan roll, PL 5.25 Item 23. • Scan roll idlers, PL 5.10 Item 18. • Gate roll, PL 5.25 Item 15. • Gate roll idlers, PL 5.10 Item 18. • Exit roll, PL 5.20 Item 2. • Exit roll idlers, PL 5.20 Item 20. 5. Check that the scan sensor actuator, PL 5.25 Item 28 moves freely and is not damaged. 6. Enter dC330 code 05-140. Check the scan sensor (Q05-140). NOTE: The scan sensor is mounted on the DADF PWB, PL 5.20 Item 6. 7. Remove the DADF rear cover, PL 5.10 Item 4. Enter dC330 code 05-200. Check that the DADF scan motor, PL 5.25 Item 12 runs and drives the following components: • Duplex roll, PL 5.25 Item 22. • Scan roll, PL 5.25 Item 23. • Gate roll, PL 5.25 Item 15. 8. Enter code 05-210. Check that the DADF duplex motor, PL 5.25 Item 5 runs and drives the exit roll, PL 5.20 Item 2. 9. Check the wiring between the DADF scan motor and CN4 on the DADF PWB. 10. Check the wiring between the duplex motor and CN5 on the DADF PWB. 11. If necessary, install new components: • DADF PWB, PL 5.20 Item 6. • DADF scan motor, PL 5.25 Item 12. • DADF scan motor assembly, PL 5.25 Item 10. • Duplex motor assembly, PL 5.25 Item 4. • Document transport assembly, PL 5.10 Item 2.

• Code: 05-500
• Description: DADF Jam 5 RAP 05-500 The machine has detected that the DADF, DADF top cover assembly or exit assembly are open during run.
• Remedy: 1. Open the DADF top cover assembly, PL 5.15 Item 11. Remove all jammed paper. 2. Raise the DADF input tray, PL 5.10 Item 5. Remove all jammed paper. 3. Open the DADF. Check that the platen cover sensor actuator, PL 14.10 Item 12 moves freely and is not damaged. 4. Enter dC330 code 05-400. Check the platen cover sensor (Q05-400), PL 14.10 Item 14. 5. Check the wiring between the platen cover sensor and CN3 on the Scanner PWB. If necessary, install a new platen cover sensor, PL 14.10 Item 14. 6. Open the DADF top cover assembly, PL 5.15 Item 11. Check that the door open switch actuator is not damaged. 7. Enter dC330 code 05-160. Check the DADF door open switch (S05-160), PL 5.25 Item 8. 8. Check the wiring between the DADF door open switch and CN6 on the DADF PWB. If necessary, install a new DADF door open switch, PL 5.25 Item 8. 9. Open the exit assembly, PL 5.20 Item 26. Check that the exit open sensor actuator is not damaged. 10. Enter dC330 code 05-180. Check the exit open sensor (Q05-180), PL 5.20 Item 16. 11. Check the wiring between the exit open sensor and CN6 on the DADF Sensor PWB. If necessary, install a new exit open sensor, PL 5.20 Item 16. 12. Check the wiring between CN1 on the DADF Sensor PWB and CN3 on the DADF PWB. 13. If necessary, install new components: • DADF PWB, PL 5.20 Item 6. • DADF sensor PWB, PL 5.20 Item 4. • Document transport assembly, PL 5.10 Item 2. • Scanner assembly, PL 14.10 Item 1.

• Code: 05-600
• Description: DADF Jam 6 RAP 05-600 The machine has detected that a DADF sensor is actuated when the machine is switched on.
• Remedy: 1. Open the DADF top cover assembly, PL 5.15 Item 11. Remove all jammed paper. 2. Raise the DADF input tray, PL 5.10 Item 5. Remove all jammed paper. 3. Check the document path for damage or obstructions. 4. Check that the following actuators move freely and are not damaged: • Document detect sensor actuator, PL 5.20 Item 17. • Paper width sensor actuator, PL 5.20 Item 17. • Paper length sensor actuator, PL 5.10 Item 14. • Registration sensor actuator, PL 5.15 Item 12. • Scan sensor actuator, PL 5.25 Item 28. • Gate sensor actuator, PL 5.10 Item 26. • Duplex sensor actuator, PL 5.25 Item 27. 5. Enter dC330. Check the following sensors. Install new components as necessary: • Code 05-100, document detect sensor (Q05-100), PL 5.20 Item 13. • Code 05-110, paper width sensor (Q05-110), PL 5.20 Item 13. • Code 05-120, paper length sensor (Q05-120), PL 5.10 Item 12. • Code 05-130, registration sensor (Q05-130), PL 5.15 Item 14. • Code 05-140, scan sensor (Q05-140). • Code 05-150, gate sensor (Q05-150), PL 5.10 Item 24. • Code 05-170, duplex sensor (Q05-170). NOTE: The scan sensor and duplex sensor are mounted on the DADF PWB, PL 5.20 Item 6. 6. Check the following wiring: • Between the document detect sensor, and CN4 on the DADF Sensor PWB. • Between the paper width sensor and CN4 on the DADF Sensor PWB. • Between the paper length sensor and CN3 on the DADF Sensor PWB. • Between the registration sensor and CN5 on the DADF Sensor PWB. • Between the gate sensor and CN2 on the DADF Sensor PWB. • Between CN1 on the DADF Sensor PWB and CN3 on the DADF PWB. 7. If necessary, install new components: • DADF PWB, PL 5.20 Item 6. • DADF sensor PWB, PL 5.20 Item 4. • Document transport assembly, PL 5.10 Item 2.

• Code: 05-700
• Description: DADF Jam 7 RAP 05-700 The machine has detected that a oversize document has been fed.
• Remedy: 1. Open the DADF top cover assembly, PL 5.15 Item 11. Remove all jammed paper. 2. Raise the DADF input tray, PL 5.10 Item 5. Remove all jammed paper. 3. Check that the customer is not attempting to feed documents outside of specification, refer to GP 8 DADF Document Feeding Specifications. 4. Check the feed roll assembly, PL 5.15 Item 5. If necessary, install a new feed roll assembly, PL 5.15 Item 5. 5. Check the retard pad, PL 5.20 Item 12. If necessary, install a new retard pad, PL 5.20 Item 12. 6. Check that the registration sensor actuator, PL 5.15 Item 12 moves freely and is not damaged. 7. Enter dC330 code 05-130. Check the registration sensor (Q05-130), PL 5.15 Item 14. 8. Check the wiring between the registration sensor and CN5 on the DADF Sensor PWB. If necessary, install a new registration sensor, PL 5.15 Item 14. 9. If necessary, install new components: • DADF PWB, PL 5.20 Item 6. • DADF sensor PWB, PL 5.20 Item 4. • Document transport assembly, PL 5.10 Item 2.

• Code: 05-900
• Description: DADF Jam 0 RAP 05-900 The lead edge of the document failed to actuate the registration sensor within the correct time.
• Remedy: 1. Remove all jammed paper from the DADF input tray. 2. Open the DADF top cover assembly, PL 5.15 Item 11. Check the document path for damage or obstructions. 3. Check the feed roll assembly, PL 5.15 Item 5. If necessary, install a new feed roll assembly, PL 5.15 Item 5. 4. Check the retard pad, PL 5.20 Item 12. If necessary, install a new retard pad, PL 5.20 Item 12. 5. Check that the registration sensor actuator, PL 5.15 Item 12 moves freely and is not damaged. 6. Enter dC330 code 05-130. Check the registration sensor (Q05-130), PL 5.15 Item 14. 7. Check the wiring between the registration sensor and CN5 on the DADF Sensor PWB. If necessary, install a new registration sensor, PL 5.15 Item 14. 8. Check the wiring between CN1 on the DADF Sensor PWB and CN3 on the DADF PWB. 9. Enter dC330 code 05-200. Check that the DADF scan motor (MOT05-200), PL 5.25 Item 12 runs. 10. While the DADF scan runs, stack the code 05-300 to energize the pick up clutch (CL05- 300). Check that the feed roll, PL 5.15 Item 5 rotates. 11. Check the wiring between the pick up clutch and CN6 on the DADF PWB. If necessary, install a new pick up clutch, PL 5.15 Item 4. 12. Check the wiring between the DADF scan motor and CN4 on the DADF PWB. 13. If necessary, install new components: • DADF PWB, PL 5.20 Item 6. • DADF sensor PWB, PL 5.20 Item 4. • DADF scan motor, PL 5.25 Item 12. • DADF scan motor assembly, PL 5.25 Item 10. • Document transport assembly, PL 5.10 Item 2.

• Code: 05-920
• Description: DADF Door Open RAP 05-920 The machine has detected that the DADF door is open.
• Remedy: 1. Open the DADF top cover assembly, PL 5.15 Item 11. Check that the DADF door open switch actuator on the top cover, PL 5.15 Item 22 is not missing or damaged. Install new components as necessary, PL 5.15. 2. Enter dC330 code 05-160. Check the DADF door open switch (S05-160), PL 5.25 Item 8. 3. Check the wiring between the DADF door open switch and CN6 on the DADF PWB. If necessary, install a new DADF door open switch, PL 5.25 Item 8. 4. If necessary, install new components: • DADF PWB, PL 5.20 Item 6. • Document transport assembly, PL 5.10 Item 2.

• Code: 05-930
• Description: DADF Exit Door Open RAP 05-930 The machine has detected that the DADF exit door is open.
• Remedy: 1. Raise the DADF input tray, PL 5.10 Item 5. Open the DADF exit assembly, PL 5.20 Item 26. Check that the DADF exit sensor actuator is not missing or damaged. Install new components as necessary, PL 5.20. 2. Enter dC330 code 05-180. Check the DADF exit open sensor (Q05-180), PL 5.20 Item 16. 3. Check the wiring between the DADF exit open sensor and CN6 on the DADF Sensor PWB. If necessary, install a new DADF exit open sensor, PL 5.20 Item 16. 4. Check the wiring between CN1 on the DADF Sensor PWB and CN3 on the DADF PWB. 5. If necessary, install new components: • DADF PWB, PL 5.20 Item 6. • DADF sensor PWB, PL 5.20 Item 4. • Document transport assembly, PL 5.10 Item 2.