• Code: 08-600
• Description: Duplex Jam 0 RAP 08-600 The lead edge of the document failed to actuate the feed sensor within the correct time.
• Remedy: 1. Open the right hand cover. Remove all jammed paper. 2. Check the paper path for damage or obstructions. 3. Check that the feed sensor actuator, PL 8.15 Item 5 moves freely and is not damaged. If necessary, install a new feed sensor actuator assembly, PL 8.15 Item 14. 4. Enter dC330 code 08-100. Check the feed sensor (Q08-100), PL 8.15 Item 8. 5. Check the wiring between the feed sensor and CN13 on the Main PWB. If necessary, install a new feed sensor, PL 8.15 Item 8. 6. Enter dC330 code 04-100 to run the main BLDC motor. 7. While the main BLDC motor runs, stack the code 08-850 to energize the registration clutch (CL08-850). Check that the registration roll, PL 4.15 Item 1 rotates. 8. Check the wiring between the registration clutch, PL 4.15 Item 4 and CN13 on the Main PWB. Install new components as necessary, PL 4.15. 9. Clean the registration roll, PL 4.15 Item 1 and the registration roll idler, PL 4.15 Item 7. Install new components as necessary. 10. If necessary, install a new main PWB, PL 1.10 Item 1.

• Code: 08-610
• Description: Duplex Jam 1 RAP 08-610 The lead edge of the document failed to actuate the duplex jam 1 sensor within the correct time in reverse mode.
• Remedy: 1. Open the right hand cover. Remove all jammed paper. 2. Unclip the duplex assembly, PL 7.30 Item 28. Check that the paper path is clear and not damaged. 3. Check that the duplex jam 1 sensor actuator, PL 7.30 Item 20 moves freely and is not damaged. 4. Enter dC330 code 08-700. Check the duplex jam 1 sensor (Q08-700), PL 7.30 Item 18. 5. Check the wiring between the duplex jam 1 sensor and CN25 on the Main PWB. If necessary, install a new duplex jam 1 sensor, PL 7.30 Item 18. 6. Enter dC330 code 04-300, then code 04-310. Check that the duplex motor (MOT04-300), PL 10.20 Item 2, runs in forward and reverse and drives the duplex roll, PL 10.15 Item 22. 7. Check the wiring between the duplex motor and CN12 on the Main PWB. Install new components as necessary, PL 10.15 and PL 10.20. 8. Enter dC330 code 08-870. Check that the duplex gate solenoid (SOL08-870), PL 10.15 Item 4 energises and lowers the duplex gate, PL 10.15 Item 15. 9. Check the duplex gate for damage. If necessary, install a new duplex gate, PL 10.15 Item 15. 10. Check the wiring between the duplex gate solenoid and CN6 on the Main PWB. If necessary, install a new duplex gate solenoid, PL 10.15 Item 4. 11. Check that the following components are clean and rotate freely: • Duplex roll, PL 10.15 Item 22. • Duplex roll idlers, PL 10.15 Item 9. 12. If necessary, install new components: • Exit assembly, PL 10.15 Item 1. • Right cover assembly, PL 7.30 Item 1. • Main PWB, PL 1.10 Item 1.

• Code: 08-620
• Description: Duplex Jam 2 RAP 08-620 The lead edge of the document failed to actuate the duplex jam 2 sensor within the correct time.
• Remedy: 1. Open the right hand cover. Remove all jammed paper. 2. Check that the paper path is clear and not damaged. 3. Check that the duplex jam 2 sensor actuator, PL 8.15 Item 10 moves freely and is not damaged. 4. Enter dC330 code 08-710. Check the duplex jam 2 sensor (Q08-710), PL 8.15 Item 8. 5. Check the wiring between the duplex jam 2 sensor and CN13 on the Main PWB. If necessary, install a new duplex jam 2 sensor, PL 8.15 Item 8. 6. Enter dC330 code 04-100 to run the main BLDC motor. 7. Enter dC330 code 08-860 to energize the duplex feed clutch (CL08-860), PL 7.30 Item 4. Manually rotate the drive gear on the duplex feed clutch. Check that the duplex feed rolls, PL 7.30 Item 10 and PL 7.30 Item 12 are clean and rotate freely. Install new components as necessary. 8. Check the wiring between the duplex feed clutch and CN25 on the Main PWB. Install new components as necessary, PL 7.30. 9. Check that the duplex feed roll idlers, PL 7.35 Item 6 are clean and rotate freely. Install new components as necessary, PL 7.35. 10. If necessary, install new components: • Right cover assembly, PL 7.30 Item 1. • Main PWB, PL 1.10 Item 1.

• Code: 08-700
• Description: Out Bin Full RAP 08-700 The machine has detected that the exit tray is full.
• Remedy: 1. Remove all documents from the exit tray. Check that the out bin full sensor actuator, PL 10.15 Item 25 moves freely and is not damaged. 2. Enter dC330 code 08-720. Check the out bin full sensor (Q08-720), PL 10.15 Item 2. 3. Check the wiring between the out bin full sensor and CN6 on the Main PWB. If necessary, install a new out bin full sensor, PL 10.15 Item 2. 4. Enter dC330 code 04-200. Check that the exit motor (MOT04-200), PL 10.20 Item 2, runs and drives the upper exit roll, PL 10.15 Item 23. 5. Check the wiring between the exit motor and CN12 on the Main PWB. Install new components as necessary, PL 10.15 and PL 10.20. 6. If necessary, install new components: • Exit assembly, PL 10.15 Item 1. • Main PWB, PL 1.10 Item 1.

• Code: 09-100
• Description: Toner Low RAP 09-100 The machine has detected that the toner module is almost empty.
• Remedy: 1. No immediate action is necessary. Ensure that a replacement toner module, PL 9.10 Item 2 is in stock. NOTE: The toner low message is based on a pixel count, not a signal from a sensor. It cannot be reset by shaking the toner module.

• Code: 09-200
• Description: Toner Empty RAP 09-200 The machine has detected that the toner module is empty.
• Remedy: 1. Make sure that the toner module is not empty. If necessary, install a new toner module, PL 9.10 Item 2. 2. Enter dC330 code 09-600 and 09-700. Check that the toner dispense motor (MOT09- 600), PL 4.20 Item 3 runs and deactuates the toner sensor (Q09-700). NOTE: It may be necessary to enter the codes several times to ensure that the toner dispense motor deactuates the toner sensor. It may also be necessary to make several copies to prevent over toning the xerographic module. 3. Remove the toner module, PL 9.10 Item 2 and xerographic module, PL 9.10 Item 1. Enter dC330 code 09-600. Make sure that the toner dispense motor runs and drives the toner dispense idler gear, PL 4.20 Item 7 and coupling, PL 4.20 Item 9. Install new components as necessary, PL 4.20. 4. Check the wiring between the toner dispense motor and CN9 on the Main PWB. 5. Check the wiring between the xerographic module connector, PL 4.15 Item 17 and CN11 on the Main PWB. If necessary, install a new xerographic module connector, PL 4.15 Item 17. 6. Install new components as necessary: • Xerographic module, PL 9.10 Item 1. • Main PWB, PL 1.10 Item 1.

• Code: 09-210
• Description: Toner Sensor RAP 09-210 The machine has detected that the toner sensor is not controlled.
• Remedy: 1. Check the wiring between the xerographic module connector, PL 4.15 Item 17 and CN11 on the Main PWB. If necessary, install a new xerographic module connector, PL 4.15 Item 17. 2. Install a new xerographic module, PL 9.10 Item 1.

• Code: 09-220
• Description: Toner Expire RAP 09-220 The toner module has reached the end of the design life of 20,000 print pages.
• Remedy: 1. Install a new toner module, PL 9.10 Item 2. NOTE: The toner expire message is based on a pixel count, not a signal from a sensor. It cannot be reset by shaking the toner module.