Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Xerox WorkCentre 5019 — Trang 7/13

Code: 041-210, 041-211

Description: STM NVM Out-Of-Order/ STM NVM R/W Error [STM NVM Out-Of-Order] The NVM of the STM is malfunctioning. [STM NVM R/W Error] Unable to perform NVM Read / Write for the STM.
Remedy: 1. Turn the power OFF and ON. 2. If the problem persists, replace the STM PWB. (PL 10.6)

Code: 042-325, 042-614

Description: Main Motor Rotation Error/ Main Motor Rotation Warning [Main Motor Rotation Error] The Main Drive Motor revolution failure was detected. When the Lock Up (Main Drive Motor Fail) signal of the Motor Drive output was monitored at the specified time interval after a certain time has passed since the Main Drive Motor operation had started, it was found to have failed 5 times in a row. [Main Motor Rotation Warning] The Main Drive Motor revolution failure was detected. When the Lock Up (Main Drive Motor Fail) signal of the Motor Drive output was monitored at the specified time interval after a certain time has passed since the Main Drive Motor operation had started, it was found to have failed 2 times in a row.
Remedy: Enter the CE Mode and turn ON the Output Check [042-001] (Main Drive Motor). Does the Main Drive Motor rotate? Y↓N→Check the power supply line (+24VDC, +5VDC) of the Main Drive Motor. Is the power supply of the Main Drive Motor normal? Y↓N→Check the power supply circuit to the Main Drive Motor. Turn OFF the power and check the following: • The connection between the Main Drive Motor J202 and the ESS/MCU PWB J403 for open circuit, short circuit, and poor contact. • The Drive Gear for wear, damage, and bearing blockage. • The Main Drive Motor for loading. If no problem is found, replace the following parts in sequence: • Main Drive Motor (PL 3.1) • ESS/MCU PWB (PL 18.1) Press [Stop] and turn OFF the power. Check the connection between the Main Drive Motor J202-8 and the ESS/MCU PWB J403-5 for open circuit, short circuit, and poor contact. If no problem is found, replace the following parts in sequence: • ESS/MCU PWB (PL 18.1) • Main Drive Motor (PL 3.1)

Code: 045-310

Description: Image Ready Error Unable to send the Image-valid signal cannot within the specified time. NOTE: When the attempt to expand the image has failed, [016-776 Marker Code Detection Fail] occurs after the recover operation.
Remedy: 1. Check the USB Cable (Local) for poor connection. 2. If no problem is found, replace the ESS/MCU PWB. (PL 18.1)

Code: 045-313

Description: IOT Logic Fail The IOT Software error was detected.
Remedy: 1. Turn the power OFF and ON. 2. Install the correct version of the IOT firmware. 3. If the problem persists, replace the ESS/MCU PWB. (PL 18.1)

Code: 061-321

Description: ROS Motor Fail The number of rotation of the ROS Motor did not come within the standard range within the specified time (5 s) after the ROS Motor On.
Remedy: 1. Turn the power OFF and ON. 2. Check whether the Drum Cartridge is installed. 3. Check the ROS Motor (Output Check [061-001]) for operation failure. 4. Check the LD +5VDC power supply of the LD PWB J140 pin-8. 5. If no problem is found, replace the following parts in sequence: • ROS Assembly (PL 2.1) • ESS/MCU PWB (PL 18.1)

Code: 061-325

Description: No SOS Fail. After the detection of ROS Motor Ready (steady rotation), the SOS interval was detected to be longer than the reference value 5 times in a row.
Remedy: 1. Turn the power OFF and ON. 2. Check whether the Drum Cartridge is installed. 3. Turn OFF the power and check the connections between the ESS/MCU PWB J410, J411 and the LD PWB J140, J160 for open circuits, short circuits, and poor contacts. 4. If no problem is found, replace the following parts in sequence: • ROS Assembly (PL 2.1) • ESS/MCU PWB (PL 18.1)

Code: 062-277

Description: DADF Communication Fail Transmission cannot be established between the ESS/MCU PWB and the DADF PWB.
Remedy: 1. Turn the power OFF and ON. 2. Turn OFF the power and check the connections between the ESS/MCU PWB J421 and the DADF PWB J751, J752 for open circuits, short circuits, and poor contacts. 3. If no problem is found, replace the following parts in sequence: • DADF PWB (PL 56.2) • ESS/MCU PWB (PL 18.1)

Code: 062-311

Description: IIT Software Logic Fail A software error was detected at the ESS/MCU PWB.
Remedy: 1. Turn the power OFF and ON. 2. Update the software version to the latest one. 3. If no problem is found, replace the ESS/MCU PWB. (PL 18.1)
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie