Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Xerox WorkCentre 5019 — Trang 9/13

Code: 072-210

Description: Tray 2 Lift Up Fail Any of the following was detected: • A Tray 2 Lifter error. • A Tray 2 Paper Size detector component malfunction.
Remedy: Check the following: • The Tray 2 Nudger Level Sensor (Input Check [072-103]) for operation failure. (PL 10.3) • The Tray 2 Feed/Lift Motor (Output Check [072-005] (Lift Up)) for operation failure. (PL 10.3) • The drive system between the Bottom Plate and the Tray 2 Feed/Lift Motor for operation failure. • The Tray for Paper misload • The Tray for existence of objects other than Paper. If no problem is found, replace the STM PWB. (PL 10.6)

Code: 072-212

Description: Tray 2 Size Sensor Broken Abnormal output AD value from Tray 2 Paper Size Switch was detected.
Remedy: Check the following: • Broken link and damage at the bottom of the Tray • The Actuator at the rear of the Tray for operation failure • The Tray 2 Paper Size Switch (Analog Monitor [072-050], Output Check [072-105]) for operation failure. (PL 10.1) • The Tray for Paper misload • The Tray for existence of objects other than Paper. If no problem is found, replace the STM PWB. (PL 10.6)

Code: 072-215

Description: MCU-STM Communication Fail. Communication failure between the ESS/MCU PWB and the STM PWB was detected.
Remedy: 1. Turn the power OFF and ON. 2. Turn OFF the power and check the connection between the ESS/MCU PWB J413 and the STM PWB J541C for open circuit, short circuit, and poor contact. 3. If no problem is found, replace the following parts in sequence: • STM PWB (PL 10.6) • ESS/MCU PWB (PL 18.1)

Code: 075-135

Description: Regi Sensor On Jam (MSI) During paper feed from the MSI, the Regi Sensor did not turn ON within the specified time after the MSI Feed Clutch On.
Remedy: Check the following: • The Regi Sensor (Input Check [071-105]) for operation failure. (PL 15.1) • The Main Drive Motor (Output Check [042-001]) for operation failure. (PL 3.1) • The MSI Feed Clutch (Output Check [072-006]) for operation failure. (PL 13.3) • The MSI Feed Roll and the MSI Nudger Roll for contamination, wear, and transportation failure due to deterioration. • The Drive Gear for wear and damage. • A paper transportation failure due to foreign substances on the paper path. • Usage of out of spec paper. If no problems are found, replace the ESS/MCU PWB. (PL 18.1)

Code: 077-101

Description: Regi Sensor Off Jam The Regi Sensor did not turn OFF within the specified time after the Regi Clutch On.
Remedy: Check the following: • The Regi Sensor (Input Check [071-105]) for operation failure. (PL 15.1) • The Main Drive Motor (Output Check [042-001]) for operation failure. (PL 3.1) • The Regi Clutch (Output Check [071-001]) for operation failure. (PL 15.1) • The Regi Roll and Pinch Roll for transportation failure due to contamination, wear, and deterioration. • The Transfer Unit for a decrease in the transportation force. • The Drive Gear for wear and damage. • A paper transportation failure due to foreign substances on the paper path. • Usage of out of spec paper. If no problems are found, replace the ESS/MCU PWB. (PL 18.1)

Code: 077-103

Description: Fusing Unit Exit Sensor Off Jam (Long) After the Regi Sensor Off, the Fusing Unit Exit Sensor did not turn OFF within the specified time.
Remedy: Check the following: • The Fusing Unit Exit Sensor (Input Check [071-106]) for operation failure. (PL 7.1) • The Main Drive Motor (Output Check [042-001]) for operation failure. (PL 3.1) • The Invert Motor (Output Check [071-003] (Exit)) for operation failure. (When Duplex is installed) (PL 17.1) • The Exit Roll and Pinch Roll for transportation failure due to contamination, wear, and deterioration. • The Transfer Unit for a decrease in the transportation force. • The Heat Roll for wound up, stuck paper. • The Drive Gear for wear and damage. • Usage of out of spec paper. If no problems are found, replace the ESS/MCU PWB. (PL 18.1)

Code: 077-104

Description: Fusing Unit Exit Sensor Off Jam (Short) The time taken for the Fusing Unit Exit Sensor to turn from ON to OFF is shorter than the specified time.
Remedy: Check the following: • The Fusing Unit Exit Sensor (Input Check [071-106]) for operation failure. (PL 7.1) • The Regi Sensor (Input Check [071-105]) for operation failure. (PL 15.1) • The Main Drive Motor (Output Check [042-001]) for operation failure. (PL 3.1) • The Invert Motor (Output Check [071-003] (Exit)) for operation failure. (When Duplex is installed) (PL 17.1) • The Heat Roll for wound up, stuck paper. • Usage of out of spec paper. If no problems are found, replace the ESS/MCU PWB. (PL 18.1)

Code: 077-106

Description: Fusing Unit Exit Sensor On Jam The Fusing Unit Exit Sensor did not turn ON within the specified time after the Regi Clutch On.
Remedy: Check the following: • The Fusing Unit Exit Sensor (Input Check [071-106]) for operation failure. (PL 7.1) • The Main Drive Motor (Output Check [042-001]) for operation failure. (PL 3.1) • The Regi Clutch (Output Check [071-001]) for operation failure. (PL 15.1) • The Fusing Unit Exit Chute for improper installation and deformation. • The Transfer Unit for a decrease in the transportation force. • The Drive Gear for wear and damage. • The Heat Roll for wound up, stuck paper. • A paper transportation failure due to foreign substances on the paper path. • Usage of out of spec paper. If no problems are found, replace the ESS/MCU PWB. (PL 18.1)
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie