• Code: 012-903
• Description: Paper Remains at Compiler Exit Sensor RAP Paper remains on the Compiler Exit Sensor.
• Remedy: Execute Component Control[012-150 Compile Exit Sensor]. Actuate the Compiler Exit Sensor with paper. The display changes. Y↓N→Check the connections of J8868 and P/J8988. J8868 and P/J8988 are connected correctly. Y↓N→Connect J8868 and P/J8988. Check the wire between J8868 and J8988 for an open circuit or a short circuit. The wire between J8868 and J8888 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Measure the voltage between the Finisher PWB P8988-3 (+) and GND (-). The voltage is approx. +5VDC. Y↓N→Replace the Finisher PWB (PL 23.16). Measure the voltage between the Finisher PWB P8988-2 (+) and GND (-). Actuate the Compiler Exit Sensor with paper. The voltage changes. Y↓N→Replace the Compiler Exit Sensor (PL 23.14). Replace the Finisher PWB (PL 23.16). Replace the Finisher PWB (PL 23.16).

• Code: 012-905
• Description: Compile Paper Sensor Static JAM RAP Paper remains on the Compile Paper Sensor.
• Remedy: Execute Component Control[012-150 Compile Exit Sensor]. Actuate the Compiler Exit Sensor with paper. The display changes. Y↓N→Check the connections of J8868 and P/J8988. J8868 and P/J8988 are connected correctly. Y↓N→Connect J8868 and P/J8988. Check the wire between J8868 and J8988 for an open circuit or a short circuit. The wire between J8868 and J8888 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Measure the voltage between the Finisher PWB P8988-3 (+) and GND (-). The voltage is approx. +5VDC. Y↓N→Replace the Finisher PWB (PL 23.16). Measure the voltage between the Finisher PWB P8988-2 (+) and GND (-). Actuate the Compiler Exit Sensor with paper. The voltage changes. Y↓N→Replace the Compiler Exit Sensor (PL 23.14). Replace the Finisher PWB (PL 23.16). Replace the Finisher PWB (PL 23.16).

• Code: 012-923
• Description: H-Transport Entrance SNR static JAM B RAP During standby, paper was detected by the H-Transport Entrance Sensor.
• Remedy: Execute Component Control[012-190 H-Transport Entrance Sensor]. Actuate the H-Transport Entrance Sensor (PL 23.4) with paper. The display changes. Y↓N→Check the connections of J8861 and J8987. J8861 and J8987 are connected correctly. Y↓N→Connect J8861 and J8987. Check the wire between J8861 and J8987 for an open circuit or a short circuit. The wire between J8861 and J8987 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Measure the voltage between the Finisher PWB P8987-4 (+) and GND (-). The voltage is approx. +5VDC. Y↓N→Replace the Finisher PWB (PL 23.16). Measure the voltage between the Finisher PWB P8987-6 (+) and GND (-). Actuate the H-Transport Entrance Sensor with paper. The voltage changes. Y↓N→Replace the H-Transport Entrance Sensor (PL 23.4). Replace the Finisher PWB (PL 23.16). Replace the Finisher PWB (PL 23.16).

• Code: 012-935
• Description: (A-Finisher) Paper Remains at Ent Sensor • At Power On the Finisher Entrance Sensor detected paper. • While the Main Motor was operating at initialization at Power On, the Finisher Entrance Sensor detected paper. • When the Cycle down operation at the end of a job was complete, the Finisher Entrance Sensor was On.
• Remedy: Check for paper remaining on the Finisher Entrance Sensor and how it is installed. The sensor is properly installed and free from paper. Y↓N→Remove the remaining paper and reinstall the sensor properly. Enter Component Control [012-140]. Move the Finisher Entrance Sensor actuator by hand or with a piece of paper. The display changes. Y↓N→Check the connections of P/J8709 and P/J8729. P/J8709 and P/J8729 are securely connected. Y↓N→Connect P/J8709 and P/J8729 securely. Check for an open or short circuit between J8709 and J8729. The wire between J8709 and J8729 are OK. Y↓N→Repair the open or short circuit. Measure the voltage between J8709-6 (+) on the Finisher PWB and GND (-). The voltage is approx. +5VDC. Y↓N→Go to Wirenet A-Finisher +5VDC and check the +5VDC circuit. Measure the voltage between J8709-5 (+) on the Finisher PWB and GND (-). Actuate the Finisher Entrance Sensor. The voltage changes. Y↓N→Replace the Finisher Entrance Sensor (PL 22.5). Check the wires and connectors for an intermittent open or short circuit. If the problem continues, replace the Finisher PWB (PL 22.7). Check the wires and connectors for an intermittent open or short circuit. If the problem continues, replace the Finisher PWB (PL 22.7).

• Code: 012-935
• Description: Paper at Xport Entrance Sensor Control logic reports paper at the Xport Entrance Sensor.
• Remedy: Enter Component Control [012-100], Finisher Entrance Sensor. Select Start. Actuate the Finisher Entrance Sensor. The display changes. Y↓N→Check the connections of J8869 and P/J8988. J8869 and P/J8988 are connected correctly. Y↓N→Connect J8869 and P/J8988. Check the wire between J8861 and J8988 for an open circuit or a short circuit. The wire between J8861 and J8988 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Measure the voltage between the Finisher PWB P8988-6 (+) and GND (-). The voltage is approx. +5VDC. Y↓N→Replace the Finisher PWB (PL 23.16). Measure the voltage between the Finisher PWB P8988-5 (+) and GND (-). Actuate the Finisher Entrance Sensor with paper. The voltage changes. Y↓N→Replace the Finisher Entrance Sensor (PL 23.4). Replace the Finisher PWB (PL 23.16). Replace the Finisher PWB (PL 23.16).

• Code: 012-949
• Description: Punch Waste Bin Missing RAP Punch Waste Bin Set Snr detected Punch Box to be missing.
• Remedy: Enter Component Control [14-275], Puncher Box Set Sensor (PL 23.5). Select Start. Remove and insert the Puncher Waste Bin manually. The display changes Y↓N→Select Stop. Check continuity between the Puncher Box Set Sensor and Finisher Main PWB. The continuity check is OK. Y↓N→Repair the open circuit or short circuit. Replace the Puncher Box Set Sensor (PL 23.5). If the problem continues, replace the Finisher PWB (PL 23.16). Check the Puncher Waste Box Actuator and Guide for deformation. The Puncher Waste Bin can be removed and inserted properly. Y↓N→Repair or replace the Puncher Waste Bin (PL 23.5). Select Stop. If the problem continues, replace the Finisher PWB (PL 23.16).

• Code: 013-210
• Description: Booklet Staple Move Home SNR ON Fail RAP Booklet Staple Move Home SNR does not turn on within designated time period
• Remedy: Check the Staple Move Home Sensor for the following: • wiring • connections • operation • voltage

• Code: 013-211
• Description: Booklet Staple Move Home SNR OFF Fail RAP Booklet Staple Move Home SNR does not turn off within designated time period
• Remedy: Check the Staple Move Home Sensor for the following: • wiring • connections • operation • voltage