• Code: 072-211
• Description: Tray 2 Broken RAP The Tray 2 Paper Size Switch failed.
• Remedy: Remove Trays 1 and 2. Replace Tray 1 with Tray 2. [072-211] occurs. Y↓N→Replace the faulty part of the Tray 2 Actuator. Check the installation of the Tray 2 Paper Size Switch. The Tray 2 Paper Size Switch is installed correctly. Y↓N→Install the Tray 2 Paper Size Switch correctly. Go to the OF 2 (SIZE SWITCH ASSY RAP).

• Code: 073-101
• Description: Tray 3 Miss Feed JAM RAP After the Tray 3 Feed/Lift Motor turned On, the Tray 3 Feed Out Sensor did not turn On within the specified time.
• Remedy: Check the Transport Roll for wear and paper powder. The Transport Roll is ok. Y↓N→Replace the Transport Roll. Check for foreign substances, distortion and paper powder in the paper transport path. No distortion, foreign substances, or paper powder are found in the paper transport path. Y↓N→Clear away the foreign substances and paper powder. Correct the distortion. Execute Component Control [071-101 Tray 3 Feed Out Sensor]. Actuate the Tray 3 Feed Out Sensor (PL 12.5/PL 13.5) with paper. The display changes. Y↓N→Check the connections of P/J821, P/J841, P/J548, P/J541 and P/J413. P/J821, P/ J841 P/J548, P/J541 and P/J413 are connected correctly. Y↓N→Connect P/J821, P/J841, P/J548, P/J541 and P/J413. Check the wire between J821 and J548 for an open circuit or a short circuit. The wire between J821 and J548 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Measure the voltage between the Tray Module PWB P548-8 (+) and GND (-). The voltage is approx. +5VDC. Y↓N→Replace the Tray Module PWB (PL 12.6/PL 13.8). Measure the voltage between the Tray Module PWB P548-10 (+) and GND (-). Actuate the Tray 3 Feed Out Sensor (PL 12.5/PL 13.5) with paper. The voltage changes. Y↓N→Replace the Tray 3 Feed Out Sensor (PL 12.5/PL 13.5). Check the wire between J541-10 and J413-B4 for an open circuit or a short circuit. The wire between J541-10 and J413-B4 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Measure the voltage between the MCU PWB P413-B4 (+) and GND (-). Actuate the Tray 3 Feed Out Sensor (PL 12.5/PL 13.5) with paper. The voltage changes. Y↓N→Replace the Tray Module PWB (PL 12.6/PL 13.8). Replace the MCU PWB (PL 9.1). Execute Component Control [073-009 Tray 3 Feed/Lift Motor ON]. The Tray 3 Feed/Lift Motor (PL 12.3/PL 13.6) can be heard. Y↓N→Check the connections of P/J220B, P/J661B, P/J549, P/J541 and P/J413. P/J220B, P/J661B, P/J549, P/J541 and P/J413 are connected correctly. Y↓N→Connect P/J220B, P/J661B, P/J549, P/J541 and P/J413. Remove the Tray 3 Feed/Lift Motor (PL 12.3/PL 13.6) and the Tray 4 Feed/Lift Motor (PL 12.3/PL 13.6). Replace the Tray 3 Feed/Lift Motor with the Tray 4 Feed/Lift Motor. Execute Component Control [073-009 Tray 3 Feed/Lift Motor ON]. The Tray 4 Feed/Lift Motor (PL 12.3/PL 13.6) can be heard. Y↓N→Return the Tray 4 Feed/Lift Motor to its original position. Check the wire between J220B and J549 for an open circuit or a short circuit. The wire between J220B and J549 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Replace the Tray Module PWB (PL 12.6/PL 13.8). Return the Tray 4 Feed/Lift Motor to its original position. Replace the Tray 3 Feed/Lift Motor (PL 12.3/PL 13.6). Replace the Tray Module PWB (PL 12.6/PL 13.8).

• Code: 073-102
• Description: Tray 2 Feed Out Sensor On JAM (Tray 3 Feed) RAP After the Tray 3 Feed Out Sensor turned On, the Tray 2 Feed Out Sensor did not turn On within the specified time.
• Remedy: Check the Transport Roll for wear and paper powder. The Transport Roll is ok. Y↓N→Replace the Transport Roll. Check for foreign substances, distortion and paper powder in the paper transport path. No distortion, foreign substances, or paper powder are found in the paper transport path. Y↓N→Clear away the foreign substances and paper powder. Correct the distortion. Execute Component Control [071-100 Tray 2 Feed Out Sensor]. Actuate the Tray 2 Feed Out Sensor (PL 2.5) with paper. The display changes. Y↓N→Check the connections of P/J105, P/J608 and P/J410. P/J105, P/J608 and P/J410 are connected correctly. Y↓N→Connect P/J105, P/J608 and P/J410. Check the wire between J105 and J410 for an open circuit or a short circuit. The wire between J105 and J410 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Measure the voltage between the MCU PWB P410-6 (+) and GND (-). The voltage is approx. +5VDC. Y↓N→Replace the MCU PWB (PL 9.1). Measure the voltage between the MCU PWB P410-8 (+) and GND (-). Actuate the Tray 2 Feed Out Sensor (PL 2.5) with paper. The voltage changes. Y↓N→Replace the Tray 2 Feed Out Sensor (PL 2.5). Replace the MCU PWB (PL 9.1). Execute Component Control [073-006 2TM/TTM Takeaway Motor ON]. The 2TM/TTM Takeaway Motor (PL 12.6/PL 13.8) can be heard. Y↓N→Check the connections of P/J826 and P/J552. P/J826 and P/J552 are connected correctly. Y↓N→Connect P/J826 and P/J552. Check the wire between J826 and J552 for an open circuit or a short circuit. The wire between J826 and J552 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Replace the MCU PWB (PL 9.1). If the problem persists, replace the Tray Module PWB (PL 12.6/PL 13.8). Replace the Tray Module PWB (PL 12.6/PL 13.8).

• Code: 073-105
• Description: Tray 3 Registration Sensor On JAM RAP After the Tray 3 Feed Out Sensor turned On, the Registration Sensor did not turn On within the specified time.
• Remedy: Check the Transport Roll for wear and paper powder. The Transport Roll is ok. Y↓N→Replace the Transport Roll.Check for foreign substances, distortion and paper powder in the paper transport path. No distortion, foreign substances, or paper powder are found in the paper transport path. Y↓N→Clear away the foreign substances and paper powder. Correct the distortion. Execute Component Control [089-100 Registration Sensor]. Manually activate the actuator of the Registration Sensor (PL 2.4). The display changes. Y↓N→Check the connection of P/J104. P/J104 is connected correctly. Y↓N→Connect P/J104. Check the wire between J104 and J403 for an open circuit or a short circuit. The wire between J104 and J403 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Measure the voltage between the MCU PWB P403B-13 (+) and GND (-). The voltage is approx. +5VDC. Y↓N→Replace the MCU PWB (PL 9.1). Measure the voltage between the MCU PWB P403B-8 (+) and GND (-). Actuate the Registration Sensor with paper. The voltage changes. Y↓N→Replace the Registration Sensor (PL 2.4). Replace the MCU PWB (PL 9.1). Execute Component Control [071-015 Takeaway Roll Clutch ON]. The Takeaway Roll Clutch (PL 2.4) can be heard. Y↓N→Check the connections of P/J204 and P/J410. P/J204 and P/J410 are connected correctly. Y↓N→Connect P/J204 and P/J410. Measure the resistance of the Takeaway Roll Clutch (PL 2.4). (Between P204-1 and P204-2) The resistance is approx. 250~100Ohm. Y↓N→Replace the Takeaway Roll Clutch (PL 2.4). Check the wire between J204 and J410 for an open circuit or a short circuit. The wire between J204 and J410 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Replace the MCU PWB (PL 9.1). Execute Component Control [073-006 2TM/TTM Takeaway Motor ON]. The 2TM/TTM Takeaway Motor (PL 12.6/PL 13.8) can be heard. Y↓N→Check the connections of P/J826 and P/J552. P/J826 and P/J552 are connected correctly. Y↓N→Connect P/J826 and P/J552. Check the wire between J826 and J552 for an open circuit or a short circuit. The wire between J826 and J552 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Replace the MCU PWB (PL 9.1). If the problem persists, replace the Tray Module PWB (PL 12.6/PL 13.8). Replace the MCU PWB (PL 9.1). If the problem persists, replace the Tray Module PWB (PL 12.6/PL 13.8).

• Code: 073-210
• Description: Tray 3 Lift Up Failure RAP • After the 2TM-Tray 3 Feed/Lift Motor turned On, the 2TM-Tray 3 Level Sensor did not turn On within the specified time. • After the TTM-Tray 3 Feed/Lift Motor turned On, the TTM-Tray 3 Level Sensor did not turn On within the specified time.
• Remedy: Remove the tray and reinstall. The Tray 3 Feed/Lift Motor can be heard. Y↓N→Execute Component Control [073-009 Tray 3 Feed/Lift Motor ON]. The Tray 3 Feed/Lift Motor (PL 12.3/PL 13.6) can be heard. Y↓N→Check the connections of P/J220B, P/J661B and P/J549. P/J220B, P/J661B and P/J549 are connected correctly. Y↓N→Connect P/J220B, P/J661B and P/J549. Remove the Tray 3 Feed/Lift Motor (PL 12.3/PL 13.6) and the Tray 4 Feed/Lift Motor (PL 12.3/PL 13.6). Replace the Tray 3 Feed/Lift Motor with the Tray 4 Feed/Lift Motor. Execute Component Control [073-009 Tray 3 Feed/Lift Motor ON]. The Tray 4 Feed/Lift Motor (PL 12.3/PL 13.6) can be heard. Y↓N→Return the Tray 3 Feed/Lift Motor to its original position. Check the wire between J220B and J549 for an open circuit or a short circuit. The wire between J220B and J549 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Replace the Tray Module PWB (PL 12.6/PL 13.8). Return the Tray 4 Feed/Lift Motor to its original position. Replace the Tray 3 Feed/Lift Motor (PL 12.3/PL 13.6). Go to the OF 2 (SIZE SWITCH ASSY RAP). Check the installation of the Tray 3 Level Sensor (PL 12.3/PL 13.6) and the operation of the actuator. The Tray 4 Level Sensor is installed correctly and the actuator works. Y↓N→Reinstall the Tray 4 Level Sensor. Execute Component Control [071-208 Tray 3 Level Sensor]. Manually activate the Tray 3 Level Sensor (PL 12.3/PL 13.6). The display changes. Y↓N→Check the connections of P/J101B, P/J661B and P/J549. P/J101B, P/J661B and P/ J549 are connected correctly. Y↓N→Connect P/J101B, P/J661B and P/J549. Check the wire between J101B and J549 for an open circuit or a short circuit. The wire between J101B and J549 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Measure the voltage between the Tray Module PWB P549-B7 (+) and GND (-). The voltage is approx. +5VDC. Y↓N→Replace the Tray Module PWB (PL 12.6/PL 13.8). Measure the voltage between the Tray Module PWB P549-B9 (+) and GND (-). Activate the actuator of the Tray 3 Level Sensor (PL 12.3/PL 13.6). The voltage changes. Y↓N→Replace the Tray 3 Level Sensor (PL 12.3/PL 13.6). Replace the Tray Module PWB (PL 12.6/PL 13.8). Replace the Tray Module PWB (PL 12.6/PL 13.8).

• Code: 073-211
• Description: Tray 3 Broken RAP The Tray 3 Paper Size Switch failed.
• Remedy: [For 2TM] Remove Trays 3 and 4. Replace Tray 3 with Tray 4. [073-211] occurs. Y↓N→Replace the faulty part of the Tray 3 Actuator. Check the installation of the Tray 3 Paper Size Switch. The Tray 3 Paper Size Switch is installed correctly. Y↓N→Install the Tray 3 Paper Size Switch correctly. Go to the OF 2 (SIZE SWITCH ASSY RAP). [For TTM] Check the Tray 3 Actuator. The Tray 3 Actuator is not distorted. Y↓N→Install the Tray 3 Paper Size Switch correctly. Check the installation of the Tray 3 Paper Size Switch. The Tray 3 Paper Size Switch is installed correctly. Y↓N→Install the Tray 3 Paper Size Switch correctly. Go to the OF 2 (SIZE SWITCH ASSY RAP).

• Code: 074-101
• Description: Tray 4 Miss Feed JAM RAP After the Tray 4 Feed/Lift Motor turned On, the Tray 4 Feed Out Sensor did not turn On within the specified time.
• Remedy: Check the Transport Roll for wear and paper powder. The Transport Roll is ok. Y↓N→Replace the Transport Roll. Check for foreign substances, distortion and paper powder in the paper transport path. No distortion, foreign substances, or paper powder are found in the paper transport path. Y↓N→Clear away the foreign substances and paper powder. Correct the distortion. Execute Component Control [071-102 Tray 4 Feed Out Sensor]. Actuate the Tray 4 Feed Out Sensor (PL 12.5/PL 13.4) with paper. The display changes. Y↓N→Check the connections of P/J825, P/J842, P/J548, P/J541 and P/J413. The connectors are connected correctly. Y↓N→Connect the connectors. Check the wire between J825 and J548 for an open circuit or a short circuit. The wire between J825 and J548 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Measure the voltage between the Tray Module PWB P548-1 (+) and GND (-). The voltage is approx. +5VDC. Y↓N→Replace the Tray Module PWB (PL 12.6/PL 13.8). Measure the voltage between the Tray Module PWB P548-3 (+) and GND (-). Actuate the Tray 4 Feed Out Sensor (PL 12.5/PL 13.4) with paper. The voltage changes. Y↓N→Replace the Tray 4 Feed Out Sensor (PL 12.5/PL 13.4). Check the wire between J541-11 and J413-B5 for an open circuit or a short circuit. The wire between J541-11 and J413-B5 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Measure the voltage between the MCU PWB P413-B5 (+) and GND (-). Actuate the Tray 3 Feed Out Sensor (PL 12.5/PL 13.5) with paper. The voltage changes. Y↓N→Replace the Tray Module PWB (PL 12.6/PL 13.8). Replace the MCU PWB (PL 9.1). Execute Component Control [073-010 Tray 4 Feed/Lift Motor ON]. The Tray 4 Feed/Lift Motor (PL 12.3/PL 13.6) can be heard. Y↓N→Check the connections of P/J220A, P/J661A, P/J549, P/J541 and P/J413. P/J220A, P/J661A, P/J549, P/J541 and P/J413 are connected correctly. Y↓N→Connect P/J220A, P/J661A, P/J549, P/J541 and P/J413. Remove the Tray 4 Feed/Lift Motor (PL 12.3/PL 13.6) and the Tray 3 Feed/Lift Motor (PL 12.3/PL 13.6). Replace the Tray 4 Feed/Lift Motor with the Tray 3 Feed/Lift Motor. Execute Component Control [073-010 Tray 4 Feed/Lift Motor ON]. The Tray 3 Feed/Lift Motor (PL 12.3/PL 13.6) can be heard. Y↓N→Return the Tray 3 Feed/Lift Motor to its original position. Check the wire between J220A and J549 for an open circuit or a short circuit. The wire between J220A and J549 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Replace the Tray Module PWB (PL 12.6/PL 13.8). Return the Tray 3 Feed/Lift Motor to its original position. Replace the Tray 4 Feed/Lift Motor (PL 12.3/PL 13.6). Replace the Tray Module PWB (PL 12.6/PL 13.8).

• Code: 074-102
• Description: Tray 2 Feed Out Sensor On JAM (Tray 4 Feed) RAP After the Tray 4 Feed Out Sensor turned On, the Tray 2 Feed Out Sensor did not turn On within the specified time.
• Remedy: Check the Transport Roll for wear and paper powder. The Transport Roll is ok. Y↓N→Replace the Transport Roll. Check for foreign substances, distortion and paper powder in the paper transport path. No distortion, foreign substances, or paper powder are found in the paper transport path. Y↓N→Clear away the foreign substances and paper powder. Correct the distortion. Execute Component Control [071-100 Tray 2 Feed Out Sensor]. Actuate the Tray 2 Feed Out Sensor (PL 2.5) with paper. The display changes. Y↓N→Check the connections of P/J105, P/J608 and P/J410. P/J105, P/J608 and P/J410 are connected correctly. Y↓N→Connect P/J105, P/J608 and P/J410. Check the wire between J105 and J410 for an open circuit or a short circuit. The wire between J105 and J410 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Measure the voltage between the MCU PWB P410-6 (+) and GND (-). The voltage is approx. +5VDC. Y↓N→Replace the MCU PWB (PL 9.1). Measure the voltage between the MCU PWB P410-8 (+) and GND (-). Actuate the Tray 2 Feed Out Sensor (PL 2.5) with paper. The voltage changes. Y↓N→Replace the Tray 2 Feed Out Sensor (PL 2.5). Replace the MCU PWB (PL 9.1). Execute Component Control [073-006 2TM/TTM Takeaway Motor ON]. The 2TM/TTM Takeaway Motor (PL 12.6/PL 13.8) can be heard. Y↓N→Check the connections of P/J826 and P/J552. P/J826 and P/J552 are connected correctly. Y↓N→Connect P/J826 and P/J552. Check the wire between J826 and J552 for an open circuit or a short circuit. The wire between J826 and J552 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Replace the MCU PWB (PL 9.1). If the problem persists, replace the Tray Module PWB (PL 12.6/PL 13.8). Replace the Tray Module PWB (PL 12.6/PL 13.8).