• Code: 062-395
• Description: IIT PWB Power Cable Connection Fail RAP The IIT PWB power source error was detected.
• Remedy: Turn the power OFF and remove the IIT Rear Cover. Turn the power ON. Is the voltage between the Main LVPS P/J502-1 (+) and the GND (-) +24VDC? Y↓N→Go to +24VDC Power RAP. Turn the power OFF and go to IIT/DADF Wirenets and check the connection between the Main LVPS P/J502 and the IIT PWB P/J720 for open circuit, short circuit, and poor contact. If the problem persists, reload the machine software (GP 16). the problem persists, replace the IIT PWB (Switch the EEPROM) (PL 1.6).

• Code: 062-396
• Description: CCD Cable Connection Fail RAP A CCD Flat Cable connection error was detected.
• Remedy: 1. Turn the power OFF and ON. 2. Turn the power OFF and check the following: • Check the Flat Cable between the CCD Lens Assembly P/J700 and the IIT PWB P/ J710 for open circuits, short circuits, and poor contacts (especially, check whether the Flat Cable was inserted in a skewed manner). • The coaxial cable between the IIT PWB P/J7191 and the ESS PWB P/J336 for open circuit, short circuit, and poor contact If no problems are found, replace the following parts in sequence: • Reload the machine software (GP 16). • IIT PWB (Switch the EEPROM) (PL 1.6) • ESS PWB (PL 35.2)

• Code: 062-397
• Description: IIT-Cont Video Cable Connection Fail RAP An ESS Video Cable connection error was detected.
• Remedy: 1. Turn the power OFF and ON. 2. Turn the power OFF and check the coaxial cable between the IIT PWB P/J7191 and the ESS PWB P/J336 for open circuit, short circuit, and poor contact. If no problems are found, replace the following parts in sequence: • Reload the machine software (GP 16). • ESS PWB (PL 35.2) • IIT PWB (Switch the EEPROM) (PL 1.6)

• Code: 062-398
• Description: IIT-Cont I/O Cable Connection Fail RAP An ESS I/O Cable connection error was detected.
• Remedy: 1. Turn the power OFF and ON. 2. Turn the power OFF and check the coaxial cable between the IIT PWB P/J7191 and the ESS PWB P/J336 for open circuit, short circuit, and poor contact. If no problems are found, replace the following parts in sequence: • Reload the machine software (GP 16). • ESS PWB (PL 35.2) • IIT PWB (Switch the EEPROM) (PL 1.6)

• Code: 071-100
• Description: Tray 1 Pre Misfeed RAP Tray1 Pre Feed Sensor is not turned ON by the paper in specified time from Tray1 Feed Start.
• Remedy: Check the following: • The Tray 1 Pre Feed Sensor for failure: Component Control [071-105] (PL 9.5) • The Tray 1 Feed/Lift Motor failure: Component Control [071-003] CW (PL 9.6) • The connection between the Tray 1 Pre Feed Sensor P/J107 and the MCU PWB P/J410 for open circuit, short circuit, and poor contact Reload the machine software (GP 16). If no problems are found, replace the MCU PWB (PL 18.2).

• Code: 071-105
• Description: Registration Sensor On Jam (Tray 1) RAP The Registration Sensor does not turn ON within the specified time after the Registration Clutch On after the Feed from Tray 1 has started.
• Remedy: Check the following: • The Registration Sensor for failure: Component Control [077-104] (PL 15.1) • The connection between the Registration Sensor P/J121 and the MCU PWB P/J415 for open circuit, short circuit, and poor contact • The Main Drive Motor for revolution failure: Component Control [042-003] CW (PL 3.2) Reload the machine software (GP 16). If no problems are found, replace the MCU PWB (PL 18.2).

• Code: 071-210
• Description: Tray 1 Lift Fail RAP Tray 1 Lift NG has occurred 3 times in a row.
• Remedy: Remove Tray 1. Turn the power ON and enter the Diag mode. Turn ON Component Control [071-002] CCW [071-003] CW] (Tray 1 Feed/Lift Motor). Does the Tray 1 Feed/Lift Motor rotate? Y↓N→Check the connection between the MCU PWB P/J417 and the Tray 1 Feed/Lift Motor P/ J213 for open circuit, short circuit, and poor contact. Measure the resistance between the MCU PWB P/J417-5/6/7/8 and the Frame. Is the resistance infinite for all? Y↓N→Check the wires of the pins with non-infinite resistance for peeled-off coatings and short circuits due to pinching. Replace the Tray 1 Feed/Lift Motor (PL 9.6). Replace the MCU PWB (PL 18.2). Press the Stop button. Turn ON Component Control [071-102] (Tray 1 Level Sensor). Use a sheet of paper, etc. to block/clear the light path to the Tray 1 Level Sensor. Does the display change between High/Low? Y↓N→Use OF 99-2 RAP to check the Tray 1 Level Sensor (PL 9.5). Press the Stop button and turn the power OFF. Reload the machine software (GP 16). Check the Tray Lift Gear for damage or the Tray Lift mechanism for mechanical load. If no problems are found, replace the MCU PWB (PL 18.2).

• Code: 071-212
• Description: Tray 1 Paper Size Switch Broken RAP Abnormal output AD value from Tray 1 Size Sensor was detected.
• Remedy: Check the following: • Broken link and breakage at the bottom of the tray • The Actuator at the rear of the Tray for operation failure • The Tray 1 Paper Size Switch for failure: Analog Monitor [071-200];Component Control [071-104] (PL 9.1) • The connection between the Tray 1 Paper Size Sensor P/J122 and the MCU PWB P/ J414 for open circuit, short circuit, and poor contact Reload the machine software (GP 16). If no problems are found, replace the MCU PWB (PL 18.2).