Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Xerox WorkCentre 5632 — Trang 21/30

Code: 11-130-120, 11-132-120

Description: Paper Exiting to Bin 0 RAP 11-130-120 The leading edge of the sheet is late to the top exit sensor. 11-132-120 The trailing edge of the sheet is late from the top exit sensor.
Remedy: NOTE: Paper is diverted to bin 0 when the diverter gate solenoid is energized. Paper is fed to bin 1 when the diverter gate solenoid is de-energized. Procedure NOTE: All 1K LCSS interlocks must be made to supply +24V to the motors. NOTE: In diagnostics, actuating any 1K LCSS sensor or switch can change the displayed state on the UI. Make sure that the correct sensor or switch is tested. Enter dC330, code 11-001 transport motor 2, MOT11-001. MOT11-001 runs. Y↓N→Go to Flag 3. Check MOT11-001. Refer to: • 11F-120 1K LCSS PWB Damage RAP. • GP 10, How to Check a Motor. • P/J16, 1K LCSS PWB. • 11C-120 1K LCSS Power Distribution RAP. Repair or install new components as necessary: • Transport motor 2, PL 11.120 Item 13. • 1K LCSS PWB, PL 11.124 Item 1. NOTE: The diverter gate solenoid remains energized for 5 seconds. Enter dC330, code 11-002 diverter gate solenoid, SOL11-002. SOL11-002 energizes. Y↓N→Go to Flag 2. Check SOL11-002. Refer to: • 11F-120 1K LCSS PWB Damage RAP. • GP 12, How to Check a Solenoid. • P/J13, 1K LCSS PWB • 11C-120 1K LCSS Power Distribution RAP. Repair or install new components as necessary: • Diverter gate solenoid, PL 11.118 Item 12. • 1K LCSS PWB, PL 11.124 Item 1. Enter dC330, code 11-130, top exit sensor, Q11-130. Actuate Q11-130. The display changes. Y↓N→Go to Flag 1. Check Q11-130. Refer to: • 11F-120 1K LCSS PWB Damage RAP. • GP 11, How to Check a Sensor. • P/J2, 1K LCSS PWB • 11C-120 1K LCSS Power Distribution RAP. Repair or install new components as necessary: • Top exit sensor, PL 11.118 Item 11. • 1K LCSS PWB, PL 11.124 Item 1. Enter dC330, code 11-000, transport motor 1, MOT11-000. MOT11-000 runs. Y↓N→Go to Flag 4. Check MOT11-000. Refer to: • 11F-120 1K LCSS PWB Damage RAP. • GP 10, How to Check a Motor. • P/J17, 1K LCSS PWB. • 11C-120 1K LCSS Power Distribution RAP. Repair or install new components as necessary: • Transport motor 1, PL 11.110 Item 2. • 1K LCSS PWB, PL 11.124 Item 1. Perform SCP 6 Final Actions.

Code: 11-130-130, 11-132-130

Description: Top Exit Jam RAP 11-130-130 The lead edge of a sheet is late arriving at the top exit sensor. 11-132-130 The trail edge of a sheet is late leaving the top exit sensor.
Remedy: Enter dC330, code 11-330. Actuate the Bin 0 90% full sensor, Q11-313. The display changes. Y↓N→Go to Flag 1. Check the sensor, Q11-313. Refer to: • GP 11, How to Check a Sensor. • P/J422, HCSS PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • Bin 0 90% full sensor, PL 11.30 Item 13. • HCSS PWB, PL 11.56 Item 5. Enter dC330, code 11-130. Actuate the top exit sensor, Q11-130. The display changes. Y↓N→Go to Flag 2. Check the sensor, Q11-130. Refer to: • GP 11, How to Check a Sensor. • P/J422, HCSS PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • Top exit sensor, PL 11.32 Item 3. • HCSS PWB, PL 11.56 Item 5. Enter dC330, code 11-002, to energise the diverter solenoid, SOL 11-002. The solenoid energises. Y↓N→Go to Flag 3. Check the solenoid SOL 11-002. Refer to: • GP 12 How to Check a Solenoid or Clutch. • P/J421, HCSS PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary. • Diverter gate solenoid, PL 11.36 Item 3. • HCSS PWB, PL 11.56 Item 5. Enter dC330 output code11-000 to run the transport motor 1B, MOT 11-000. The motor runs. Y↓N→Go to 11-120-130, 11-122-130 Compiler Carriage Jam RAP, check the transport motor 1B. The top nip rolls are driven when MOT 11-000 runs. Y↓N→Check the transport motor 1B drive belt, PL 11.38 Item 3. Perform SCP 6 Final Actions.

Code: 11-130-170, 11-132-170

Description: Top Exit Jam RAP 11-130-170 The lead edge of a sheet is late arriving at the top exit sensor. 11-132-170 The trail edge of a sheet is late leaving the top exit sensor.
Remedy: Enter dC330, code 11-330. Actuate the Bin 1 90% full sensor, Q11-313. The display changes. Y↓N→Go to Flag 1. Check the sensor, Q11-313. Refer to: • GP 11, How to Check a Sensor. • P/J422, HCSS PWB. • 11C-170 HCSS BM Power Distribution RAP. Install new components as necessary: • Bin 0 90% full sensor, PL 11.60 Item 13. • HCSS PWB, PL 11.92 Item 5. Enter dC330, code 11-130. Actuate the top exit sensor, Q11-130. The display changes. Y↓N→Go to Flag 2. Check the sensor, Q11-130. Refer to: • GP 11, How to Check a Sensor. • P/J422, HCSS PWB. • 11C-170 HCSS BM Power Distribution RAP. Install new components as necessary: • Top exit sensor, PL 11.62 Item 3. • HCSS PWB, PL 11.92 Item 5. Enter dC330, code 11-002 to energize the diverter solenoid, SOL 11-002. The solenoid energizes. Y↓N→Go to Flag 3. Check the solenoid SOL 11-002. Refer to: • GP 12 How to Check a Solenoid or Clutch. • P/J421, HCSS PWB. • 11C-170 HCSS BM Power Distribution RAP. Install new components as necessary. • Diverter solenoid, PL 11.66 Item 3. • HCSS PWB, PL 11.92 Item 5. Enter dC330 output code11-000 to run the transport motor 1B, MOT 11-000. The motor runs. Y↓N→Go to 11-120-170, 11-122-170 Compiler Carriage Jam RAP, check the transport motor 1B. The top nip rolls are driven when MOT 11-000 runs. Y↓N→Check the transport motor 1B drive belt, PL 11.70 Item 3. Perform SCP 6 Final Actions.

Code: 11-130-171, 11-132-171

Description: HVF Top Exit Sensor RAP 11-130-171 The paper leading edge is late arriving at the top exit sensor. 11-132-171 The paper trailing edge is late leaving the top exit sensor.
Remedy: . shows the location of the components. Enter dC330, code 11-130. Manually operate the top exit sensor, Q11-130. The display changes. Y↓N→Go to Flag 1. Check the sensor, Q11-130. Refer to: • GP 11 How to Check a Sensor. • P/J101, HVF Control PWB • 11A-171 HVF Power Distribution RAP Install new components as necessary: • Top exit sensor, PL 11.156. • HVF Control PWB, PL 11.157 Item 2 Enter dC330, code 11-002. Energize the exit diverter solenoid SOL 11-002. The solenoid energizes. Y↓N→Go to Flag 2. Check the solenoid, SOL 11-002. Refer to: • GP 12, How to Check a Solenoid or Clutch. • P/J102, HVF control PWB. • 11A-171 HVF Power Distribution RAP. Install new components as necessary: • Exit diverter solenoid, PL 11.150 Item 16. • HVF control PWB, PL 11.157 Item 2 Enter dC330, code 11-001 to run the exit feed motor 2, MOT 11-001. The motor runs. Y↓N→Go to Flag 3. Check the exit feed motor 2, MOT 11-001. Refer to: • GP 10 How to Check a Motor. • P/J102, HVF Control PWB • 11A-171 HVF Power Distribution RAP Install new components as necessary: • Exit feed motor, PL 11.150 Item 10. • HVF control PWB, PL 11.157 Item 2. Check the drive belt on the motor. The drive belt is good. Y↓N→Install a new drive belt, PL 11.150 Item 14. The fault may be intermittent, check for damaged wiring or bad connectors. If necessary install new components: • Top exit sensor, PL 11.156. • Exit diverter solenoid, PL 11.150 Item 16. • Diverter gate, PL 11.153 Item 9. • Exit feed motor 2, PL 11.150 Item 10. • HVF control PWB, PL 11.157 Item 2.

Code: 11-140-110, 11-142-110

Description: Sheet Late to Bin 1 RAP 11-140-110 The leading edge of the sheet is late to the 2nd to top exit sensor, Q11-140. 11-142-110 The trailing edge of the sheet is late to the 2nd to top exit sensor, Q11-140.
Remedy: NOTE: All 2K LCSS interlocks must be made to supply +24V to the motors. NOTE: In diagnostics, actuating any 2K LCSS sensor or switch can change the displayed state on the UI. Make sure that the correct sensor or switch is tested.. Enter dC330, code 11-001 to energize the transport motor 2, MOT11-001. The motor energizes. Y↓N→Go to Flag 3 and check MOT11-001. Refer to: • 11G-110 2K LCSS PWB Damage RAP. • GP 10, How to check a motor. • P/J309, 2K LCSS PWB. • 11D-110 2K LCSS Power Distribution RAP. Repair or install new components as necessary: • Transport motor 2, PL 11.22 Item 5. • 2K LCSS PWB, PL 11.26 Item 1. Enter dC330, code 11-002 to energize the diverter solenoid, S11-002. Energize the solenoid. The diverter solenoid energizes. Y↓N→Go to Flag 4 and check SOL11-002. Refer to: • 11G-110 2K LCSS PWB Damage RAP. • GP 12, How to Check a Solenoid or Clutch. • P/J306, 2K LCSS PWB. • 11D-110 2K LCSS Power Distribution RAP. Repair or install new components as necessary: • Diverter gate solenoid, PL 11.22 Item 12. • 2K LCSS PWB, PL 11.26 Item 1.. Enter dC330, code 11-140, actuate the 2nd to top exit sensor, Q11-140. The display changes. Y↓N→Go to Flag 1 and check Q11-140. Refer to: • 11G-110 2K LCSS PWB Damage RAP. • GP 11, How to Check a sensor. • P/J313, 2K LCSS PWB. • 11D-110 2K LCSS Power Distribution RAP. Repair or install new components as necessary: • 2nd to top exit sensor, PL 11.23 Item 4. • 2K LCSS PWB, PL 11.26 Item 1. Enter dC330, code 11-000 to energize the transport motor 1, MOT 11-000. The motor energizes. Y↓N→Go to Flag 2 and check MOT 11-000. Refer to: • 11G-110 2K LCSS PWB Damage RAP. • GP 10, How to Check a Motor. • P/J305, 2K LCSS PWB. • 11D-110 2K LCSS Power Distribution RAP. Repair or install new components as necessary: • Transport motor 1, PL 11.14 Item 2. • 2K LCSS PWB, PL 11.26 Item 1. If the fault is still present, perform 11-007-110, 11-008-110, 11-312-110, 11-313-110, 11-319- 110 Rear Tamper Move Failure RAP. NOTE: A software problem can cause the machine to incorrectly display the fault code 11-142- 110.

Code: 11-140-120, 11-142-120

Description: Sheet Late to Bin 1 RAP 11-140-120 The leading edge of the sheet is late to the 2nd to top exit sensor. 11-142-120 The trailing edge of the sheet is late to the 2nd to top exit sensor.
Remedy: NOTE: In diagnostics, actuating any 1K LCSS sensor or switch can change the displayed state on the UI. Make sure that the correct sensor or switch is tested. NOTE: All 1K LCSS interlocks must be made to supply +24V to the motors.. Enter dC330, code 11-001 transport motor 2, MOT11-001. MOT11-001 runs. Y↓N→Go to Flag 3. Check MOT11-001. Refer to: • 11F-120 1K LCSS PWB Damage RAP. • GP 10, How to check a motor. • P/J16, 1K LCSS PWB. • 11C-120 1K LCSS Power Distribution RAP. Repair or install new components as necessary: • Transport motor 2, PL 11.118 Item 5. • 1K LCSS PWB, PL 11.124 Item 1. Enter dC330, code 11-002 diverter solenoid, SOL11-002. SOL11-002 energizes. Y↓N→Go to Flag 4. Check SOL11-002. Refer to: • 11F-120 1K LCSS PWB Damage RAP. • GP 12, How to Check a Solenoid. • P/J131K LCSS PWB • 11C-120 1K LCSS Power Distribution RAP. Repair or install new components as necessary: • Diverter gate solenoid, PL 11.22 Item 12. • 1K LCSS PWB, PL 11.26 Item 1. Enter dC330, code 11-140 2nd to top exit sensor, Q11-140. Actuate Q11-140. The display changes. Y↓N→Go to Flag 1. Check Q11-140. Refer to: • 11F-120 1K LCSS PWB Damage RAP. • GP 11, How to Check a sensor. • P/J2, 1K LCSS PWB • 11C-120 1K LCSS Power Distribution RAP. Repair or install new components as necessary: • 2nd to top exit sensor, PL 11.120 Item 4. • 1K LCSS PWB, PL 11.124 Item 1. Enter dC330, code 11-000 transport motor 1, MOT11-000. MOT11-000 runs. Y↓N→Go to Flag 2. Check MOT11-000. Refer to: • 11F-120 1K LCSS PWB Damage RAP. • GP 10, How to Check a Motor. • P/J17, 1K LCSS PWB. • 11C-120 1K LCSS Power Distribution RAP. Repair or install new components as necessary: • Transport motor 1, PL 11.110 Item 2. • 1K LCSS PWB, PL 11.124 Item 1. Perform SCP 6 Final Actions.

Code: 11-140-130, 11-142-130, 11-150-130, 11-152-130

Description: Sheet Not Exiting to Bin 1 or Bin 2 RAP 11-140-130 The lead edge of a sheet is late arriving at the 2nd to top exit sensor. 11-142-130 The trail edge of a sheet is late leaving the 2nd to top exit sensor. 11-150-130 The lead edge of a sheet ia late arriving at the 2nd to top exit sensor. 11-152-130 The trail edge of a sheet is late leaving the 2nd to top exit sensor.
Remedy: Enter dC330, code 11-140. Actuate the 2nd to top exit sensor, Q11-140. The display changes. Y↓N→Go to Flag 1. Check the sensor. Refer to: • GP 11 How to Check a Sensor. • P/J409, Carriage PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • Carriage PWB, PL 11.46 Item 5. • 2nd to top exit sensor, PL 11.47 Item 5. Enter dC330, code 11-023 to run the eject motor, MOT 11-020. The eject housing cycles between open and closed. Y↓N→Go to Flag 3. Check the motor. Refer to: • GP 10 How to Check a Motor. • P/J406, Carriage PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • Carriage PWB, PL 11.46 Item 5. • Eject motor assembly, PL 11.47 Item 2. Enter dC330, code 11-010 to run the compiler carriage eject roll motor, MOT 11-120. The motor runs. Y↓N→Go to Flag 2. Check the motor. Refer to: • GP 10 How to Check a Motor. • P/J408, Carriage PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • Carriage PWB, PL 11.46 Item 5. • Eject roll motor, PL 11.49 Item 1. Check the condition of the eject motor drive belt, PL 11.49 Item 2. The drive belt is good. Y↓N→Install a new eject motor drive belt, PL 11.49 Item 2. Go to Flag 4. Check the harness and connectors P/J412 and P/J432, refer to GP 7. The wiring and connectors are good. Y↓N→Repair the wiring or install new parts as necessary. Perform SCP 6 Final Actions.

Code: 11-140-170, 11-142-170

Description: Sheet Not Exiting to Bin 1 RAP 11-140-170 The lead edge of a sheet is late arriving at the 2nd from top exit sensor. 11-142-170 The trail edge of a sheet is late leaving the 2nd from top exit sensor.
Remedy: Enter dC330, code 11-140. Actuate the 2nd from top exit sensor, Q11-140. The display changes. Y↓N→Go to Flag 1. Check the sensor Q11-140. Refer to: • GP 11, How to Check a Sensor. • P/J409, Carriage PWB. • 11C-170 HCSS BM Power Distribution RAP. Install new components as necessary: • Carriage PWB, PL 11.72 Item 5. • 2nd to top exit sensor, PL 11.73 Item 5. Enter dC330, code 11-023 to run the eject motor, MOT 11-020. The eject housing cycles between open and closed. Y↓N→Go to Flag 3. Check the motor. MOT 11-020 Refer to: • GP 10, How to Check a Motor. • P/J406, Carriage PWB. • 11C-170 HCSS BM Power Distribution RAP. Install new components as necessary: • Carriage PWB, PL 11.72 Item 5. • Eject motor, PL 11.73 Item 2. Enter dC330, code 11-010 to run the compiler carriage eject roll motor, MOT11-120. The motor runs. Y↓N→Go to Flag 2. Check the motor MOT 11-120. Refer to: • GP 10, How to Check a Motor. • P/J408, Carriage PWB. • 11C-170 HCSS BM Power Distribution RAP. Install new components as necessary: • Carriage PWB, PL 11.72 Item 5. • Eject roll motor, PL 11.75 Item 1. Check the condition of the eject motor drive belt, PL 11.75 Item 2. The drive belt is good. Y↓N→Install a new eject motor drive belt, PL 11.75 Item 2. Go to Flag 4, check the harness and connectors P/J412 and P/J432, refer to GP 7. The harness and connectors are good. Y↓N→Repair the harness, or install new parts as necessary. Perform SCP 6 Final Actions.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie