Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Xerox WorkCentre 5855 — Trang 23/28

Code: 374-500-00

Description: Tray 4 Open During Run RAP 374-500-00 Tray 4 was opened during run when the paper is fed from tray 4.
Remedy: Enter dC330 code 074-300 tray 4 home sensor, Q74-300. Press Start. Open, then fully close the tray. The display changes. Y↓N→Go to Flag 1. Check Q74-300. Refer to: • GP 11 How to Check a Sensor. • P/J3 HCF control PWB. • 301B 0V Distribution RAP. Install new components as necessary: • Tray 4 home sensor, PL 70.21 Item 4. • HCF control PWB, PL 70.21 Item 2. Check the sensor holder, PL 70.21 Item 3. If the fault remains, install new components as necessary: • Tray 4 home sensor, PL 70.21 Item 4. • HCF control PWB, PL 70.21 Item 2.

Code: 375A

Description: Bypass Tray RAP Use this RAP to identify and correct problems when using the bypass tray.
Remedy: Enter dC330 code 075-320 bypass empty sensor Q75-320. Press Start. Manually actuate the sensor. The display changes. Y↓N→Go to Flag 2. Check Q75-320. Refer to: • GP 11 How to Check a Sensor. • P/J10, IOT PWB. • 301D +3.3 V Distribution RAP. • 301B 0V Distribution RAP. If necessary, install a new bypass empty sensor, PL 70.30 Item 7. If the fault remains, perform the OF7 IOT PWB Diagnostics RAP. Enter dC140 code 075-601. Move the bypass tray width guide between wide and narrow settings. NOTE: The width sensor is a potentiometer. The arm on the potentiometer is attached to the bypass tray side guide. This gives a variable voltage to indicate the paper width setting. The displayed value changes. Y↓N→Go to Flag 1. Check Q75-601. Refer to: • GP 11 How to Check a Sensor. • P/J10, IOT PWB. • 301D +3.3 V Distribution RAP. • 301B 0V Distribution RAP. If necessary, install a new bypass tray and left hand door assembly, PL 70.30 Item 1. If the fault remains, perform the OF7 IOT PWB Diagnostics RAP. Enter dC330 code 081-050 bypass feed solenoid, SOL81-050. Press Start. The solenoid energized. Y↓N→Go to Flag 3. Check SOL81-050. Refer to: • GP 12 How to Check a Solenoid or Clutch. • P/J10, IOT PWB. • 301G +24 V Distribution RAP. • 301B 0V Distribution RAP. If necessary, install a new bypass feed solenoid, PL 70.30 Item 4. If the fault remains, perform the OF7 IOT PWB Diagnostics RAP. Perform the following: • Ensure that the customer is not filling the tray above the max fill line. • Clean the feed roll and retard pad with a cloth dampened with water. • If necessary, install a new feed roll and retard pad assembly, PL 70.30 Item 21.

Code: 376-100-00

Description: Tray 6 Elevator Lift Failure RAP 376-100-00 A signal was not detected by the encoder when the elevator motor was driving up.
Remedy: Ensure the cable holder PL 70.68 Item 23 is not trapped behind the elevator motor bracket. The cable holder is correctly positioned. Y↓N→Reposition the cable holder so that it does not become trapped behind the elevator motor bracket. Open, then close the tray 6 door. The tray moves up. Y↓N→Enter dC330 code 076-300 front door interlock switch, S76-300. Press Start. Manually toggle the door interlock switch. The display changes. Y↓N→Go to Flag 1. Check S76-300. Refer to: • GP 13 How to Check a Switch. • P/J507, Tray 6 control PWB • 301E +5V Distribution RAP. • 301B 0V Distribution RAP. Install new components as necessary: • Front door interlock switch, PL 70.60 Item 6. • Tray 6 control PWB, PL 70.68 Item 8. Enter dC330 code 076-330 stack height sensor, Q76-330. Press Start. Manually activate the stack height sensor on the paper feed assembly. The display changes. Y↓N→Go to Flag 2. Check Q76-330. Refer to: • GP 11 How to Check a Sensor. • P/J505, Tray 6 control PWB. • 301E +5V Distribution RAP. • 301B 0V Distribution RAP. Install new components as necessary: • Stack height sensor, PL 80.45 Item 7. • Tray 6 control PWB, PL 70.68 Item 8. Check the voltage at PJ504 pin 4, Flag 3. Manually actuate the upper limit switch, S76- 412. The voltage changes. Y↓N→Go to Flag 3. Check S76-412. Refer to: • GP 13 How to Check a Switch. • P/J504, Tray 6 control PWB • 301G +24V Distribution RAP. • 301B 0V Distribution RAP. Install new components as necessary: • Upper limit switch, PL 70.68 Item 12. • Tray 6 control PWB, PL 70.68 Item 8. Enter dC330 code 076-340 elevator motor encoder sensor, Q76-340. Press Start. Manually lift the motor to activate the sensor. The display changes. Y↓N→Go to Flag 4. Check Q76-340. Refer to: • GP 11 How to Check a Sensor. • P/J506, Tray 6 control PWB. • 301E +5V Distribution RAP. • 301B 0V Distribution RAP. Install new components as necessary: • Elevator motor encoder sensor, PL 70.68 Item 5. • Tray 6 control PWB, PL 70.68 Item 8 Enter dC330 code 076-010 to energise the elevator motor, MOT76-010. Press Start. The motor runs. Y↓N→Go to Flag 5. Check MOT76-010. Refer to: • GP 10 How to Check a Motor. • P/J504, Tray 6 control PWB. • 301G +24V Distribution RAP. • 301B 0V Distribution RAP Install new components as necessary: • Elevator motor, PL 70.68 Item 4. • Tray 6 control PWB, PL 70.68 Item 8 The tray 6 elevator motor is operating correctly. The tray 6 elevator motor is operating correctly.

Code: 376-101-00

Description: Tray 6 Elevator Lower Failure RAP 376-101-00 A signal was not detected by the encoder when the elevator motor was driving down.
Remedy: Ensure the cable holder is not trapped behind the elevator motor bracket. The cable holder is correctly positioned. Y↓N→Reposition the cable holder so that it does not become trapped behind the elevator motor bracket. Open, then close the tray 6 door. The tray moves down. Y↓N→Enter dC330 code 076-300 front door interlock switch, S76-300. Press Start. Manually toggle the door interlock switch. The display changes. Y↓N→Go to Flag 1. Check S76-300. Refer to: • GP 13 How to Check a Switch. • P/J507, Tray 6 control PWB. • 301E +5V Distribution RAP. • 301B 0V Distribution RAP. Install new components as necessary: • Front door interlock switch, PL 70.60 Item 6. • Tray 6 control PWB, PL 70.68 Item 8. Enter dC330 code 076-335 stack down sensor, Q76-335. Press Start. Manually activate the stack down sensor. The display changes Y↓N→Go to Flag 2. Check Q76-335. Refer to: • GP 11 How to Check a Sensor. • P/J505, Tray 6 control PWB. • 301E +5V Distribution RAP. • 301B 0V Distribution RAP. Install new components as necessary: • Stack down sensor, PL 70.68 Item 9. • Tray 6 control PWB, PL 70.68 Item 8. Check the voltage at PJ504 pin 6, Flag 3. Manually actuate the tray down limit switch, S76-415, by pressing the plate under the paper tray. The voltage changes. Y↓N→Go to Flag 3. Check S76-415. Refer to: • GP 13 How to Check a Switch. • P/J504, Tray 6 control PWB. • 301G +24V Distribution RAP. • 301B 0V Distribution RAP. Install new components as necessary: • Tray down limit switch, PL 70.70 Item 2. • Tray 6 control PWB, PL 70.68 Item 8. Enter dC330 code 076-340 elevator motor encoder sensor, Q76-340. Press Start. Manually lift the elevator motor to activate the sensor. The display changes Y↓N→Go to Flag 4. Check Q76-340. Refer to: • GP 11 How to Check a Sensor. • P/J506, Tray 6 control PWB. • 301E +5V Distribution RAP. • 301B 0V Distribution RAP. Install new components as necessary: • Elevator motor encoder sensor, PL 70.68 Item 5. • Tray 6 control PWB, PL 70.68 Item 8. Enter dC330 code 076-011 to lower the elevator motor, MOT76-010. Press Start. The motor runs Y↓N→Go to Flag 5. Check MOT76-010. Refer to: • GP 10 How to Check a Motor. • P/J504, Tray 6 control PWB. • 301G +24V Distribution RAP. • 301B 0V Distribution RAP Install new components as necessary: • Elevator motor, PL 70.68 Item 4. • Tray 6 control PWB, PL 70.68 Item 8. The elevator motor is operating correctly. Perform ADJ 70.5 Tray 6 Stack Height Sensor and Retard Shield, then perform SCP 5 Final Actions. The elevator motor is operating correctly. Perform ADJ 70.5 Tray 6 Stack Height Sensor and Retard Shield, then perform SCP 5 Final Actions.

Code: 376-500-00

Description: Tray 6 Door Open During Run RAP 376-500-00 Tray 6 door open during run when the paper is fed from tray 6.
Remedy: Enter dC330 code 076-300 front door interlock switch, S76-300. Press Start. Open, then fully close the door. The display changes. Y↓N→Go to Flag 1. Check S76-300. Refer to: • GP 13 How to Check a Switch. • 301E +5V Distribution RAP • P/J507, Tray 6 control PWB. • 301B 0V Distribution RAP. Install new components as necessary: • Front door interlock switch, PL 70.60 Item 6. • Tray 6 control PWB, PL 70.68 Item 8. If the fault remains, install new components as necessary: • Front door interlock switch, PL 70.60 Item 6. • Tray 6 control PWB, PL 70.68 Item 8.

Code: 376-510-00

Description: Tray 6 Undocked During Run RAP 376-510-00 Tray 6 was undocked during run when the paper is fed from tray 6.
Remedy: Enter dC330 code 076-310 docking interlock switch, S76-310. Press Start. Undock, then dock tray 6, refer to. The display changes. Y↓N→Go to Flag 1. Check S76-310. Refer to: • GP 13 How to Check a Switch. • P/J507, Tray 6 control PWB. •. • 301E +5V Distribution RAP. • 301B 0V Distribution RAP. Install new components as necessary: • Docking interlock switch, PL 70.64 Item 1. • Tray 6 control PWB, PL 70.68 Item 8. Perform the following: • Check that the docking latch on tray 6 is latched onto the machine. • Check the that the rail assembly is located correctly to the machine.

Code: 376A

Description: Tray 6 Empty RAP Use this RAP to solve problems associated with the tray 6 empty sensor.
Remedy: Enter dC330 code 076-320 empty sensor, Q76-320. Press Start. Manually actuate the tray empty sensor. The display changes. Y↓N→Go to Flag 1. Check Q76-320. Refer to: • GP 11 How to Check a Sensor. • P/J505, Tray 6 control PWB. • 301E +5V Distribution RAP. • 301B 0V Distribution RAP. Install new components as necessary: • Empty sensor, PL 80.45 Item 6 • Tray 6 control PWB, PL 70.68 Item 8. The fault may be intermittent. Perform the steps that follow: • Check the wiring harness for damage, GP 7. • Check that the empty sensor is located correctly.

Code: 381-100-00

Description: Wait Sensor Jam Entry RAP 381-100-00 The lead edge of the paper failed to actuate the wait sensor within the correct time from feed sensor 1.
Remedy: Identify the speed of the machine, refer to SCP 6 Machine features. Perform one of the steps that follow: • If the speed of the machine is 45-55 ppm, go to 381-100-00A Wait Sensor RAP (45-55 ppm) • If the speed of the machine is 65-90 ppm, go to 381-100-00B Wait Sensor RAP (65-90 ppm).
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie