Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Canon iR Advance C7580i — Trang 6/112

Code: 012-0401-05

Description: Drum speed detection error (Bk)
Causes: The Drum Speed Detection PCB (Bk) 1/2 detected a rotation signal error.
Remedy: [Related parts] R1.00 - Harness connecting from the Drum Driver PCB (UN6/J1907) to the Drum Speed Detection PCB (Bk) 1/2 and Drum Motor (Bk) (UN18/J7310, UN19/J7311 and M19/J7306) - Drum Speed Detection PCB (Bk) 1/2 (UN18 and UN19) - Drum Motor (Bk) (M19) - Drum Unit (Bk) - Drum Driver PCB (UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check that the Encoder Wheel of the Drum Speed Detection PCB (Bk) 1/2 is properly installed. 2. Clean the Drum Speed Detection PCB (Bk) 1/2 and the Encoder Wheel. 3. Set the Drum Unit (Bk) again. 4. Check/replace the related harness/cable, connector and parts.

Code: 012-0402-05

Description: Drum speed detection error (Bk)
Causes: The Drum Speed Detection PCB (Bk) 1 detected a rotation signal error.
Remedy: [Related parts] R1.00 - Harness connecting from the Drum Driver PCB (UN6/J1907) to the Drum Speed Detection PCB (Bk) 1 and Drum Motor (Bk) (UN18/J7310 and M19/J7306) - Drum Speed Detection PCB (Bk) 1 (UN18) - Drum Motor (Bk) (M19) - Drum Unit (Bk) - Drum Driver PCB (UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Clean the Drum Speed Detection PCB (Bk) 1 and the Encoder Wheel. 2. Set the Drum Unit (Bk) again. 3. Check/replace the related harness/cable, connector and parts.

Code: 012-0403-05

Description: Drum speed detection error (Bk)
Causes: The Drum Speed Detection PCB (Bk) 2 detected a rotation signal error.
Remedy: [Related parts] R1.00 - Harness between the Drum Driver PCB (UN6/J1907) and the Drum Speed Detection PCB (Bk) 2 (UN19/J7311) - Drum Speed Detection PCB (Bk) 2 (UN19) - Drum Driver PCB (UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Clean the Drum Speed Detection PCB (Bk) 2. 2. Check/replace the related harness/cable, connector and parts.

Code: 012-0406-05

Description: Drum Motor (Bk) rotation error
Causes: The Drum Motor (Bk) is not rotating at the specified speed, or it is stopped.
Remedy: [Related parts] R1.00 - Harness between the Drum Driver PCB (UN6/J1907) and the Drum Motor (Bk) (M19/J7306) - Drum Motor (Bk) (M19) - ITB Cleaning Blade - Drum Driver PCB (UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. - Check that the Intermediate Transfer Belt is not displaced. - Check/replace the related harness/cable, connector and parts.

Code: 012-0501-05

Description: ITB speed detection error
Causes: The ITB Drive Roller Speed Detection PCB 1/2 detected a rotation signal error.
Remedy: [Related parts] R1.00 - Harnesses connecting from the DC Controller PCB (UN2/J1242) to the Drawer Unit (J8050) to the ITB Drive Roller Speed Detection PCB 1/2 and ITB Drive Motor (UN16/J7318, UN17/J7319 and M3/J7518) - ITB Drive Roller Speed Detection PCB 1/2 (UN16 and UN17) - ITB Drive Motor (M3) - Drum Drive Unit - Drum Unit (C, M, Y, Bk) - DC Controller PCB (UN2) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check that the Encoder Wheel of the ITB Drive Roller Speed Detection PCB 1/2 is properly installed. 2. Clean the ITB Drive Roller Speed Detection PCB 1/2 and the Encoder Wheel. 3. Set the Drum Units (all colors) again. 4. Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Code: 012-0502-05

Description: ITB speed detection error
Causes: The ITB Drive Roller Speed Detection PCB 1 detected a rotation signal error.
Remedy: [Related parts] R1.00 - Harnesses connecting from the DC Controller PCB (UN2/J1242) to the Drawer Unit (J8050) to the ITB Drive Roller Speed Detection PCB 1 and ITB Drive Motor (UN16/J7318 and M3/J7518) - ITB Drive Roller Speed Detection PCB 1/2 (UN16 and UN17) - ITB Drive Motor (M3) - Drum Unit (C, M, Y, Bk) - DC Controller PCB (UN2) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Clean the ITB Drive Roller Speed Detection PCB 1 and the Encoder Wheel. 2. Set the Drum Units (all colors) again. 3. Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Code: 012-0503-05

Description: ITB speed detection error
Causes: The ITB Drive Roller Speed Detection PCB 2 detected a rotation signal error.
Remedy: [Related parts] R1.00 - Harnesses connecting from the DC Controller PCB (UN2/J1242) to the Drawer Unit (J8050) to the ITB Drive Roller Speed Detection PCB 2 and ITB Drive Motor (UN17/J7319 and M3/J7518) - ITB Drive Roller Speed Detection PCB 2 (UN17) - ITB Drive Motor (M3) - Drum Unit (C, M, Y, Bk) - DC Controller PCB (UN2) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Clean the ITB Drive Roller Speed Detection PCB 2. 2. Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Code: 012-0506-05

Description: ITB Drive Motor rotation error
Causes: The ITB Drive Motor is not rotating at the specified speed, or it is stopped.
Remedy: [Related parts] R1.00 - Harnesses connecting the DC Controller PCB (UN2/J1242), the Drawer Unit (J8050) and the ITB Drive Motor (M3/J7518) - ITB Drive Motor (M3) - ITB Cleaning Blade - DC Controller PCB (UN2) [Remedy] Perform the following in the order while checking whether the error is cleared. - Check that the Intermediate Transfer Belt is not displaced. - Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie