• Code: 008-0002-05
• Description: Fixing Film life detection error
• Causes: It was detected that the total rotation time (corresponding value) of the Fixing Film exceeded 5206 hours.
• Remedy: Replace the Fixing Film Unit. After the replacement, go through the following to clear the counter value: COPIER> COUNTER> DRBL-1> FX-BLT-U.

• Code: 008-0003-05
• Description: Fixing Film life detection error
• Causes: It was detected that the number of sheets fed through the Fixing Film (counter value) exceeded the specified value. (The upper limit of the number of the sheets fed varies depending on the location.)
• Remedy: Replace the Fixing Film Unit. After the replacement, go through the following to clear the counter value: COPIER> COUNTER> DRBL-1> FX-BLT-U.

• Code: 009-0500-05
• Description: Pressure Roller engagement/disengagement HP error
• Causes: The home position was not detected during engagement/disengagement operation of the Pressure Roller.
• Remedy: [Related parts] R1.00 - Harness connecting from the Fixing Feed Driver PCB (UN5/J1508) to the Fixing Pressure Release Sensor and Half Pressure Position Sensor (PS73/J7220 and PS110/J8033) - Harness between the Fixing Feed Driver PCB (UN5/J1507) and the Fixing Motor (M48/J7217) - Fixing Pressure Release Sensor (PS73) - Half Pressure Position Sensor (PS110) - Fixing Motor (M48) - Fixing Feed Driver PCB (UN5) - DC Controller PCB (UN2) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check/replace the related harness/cable, connector and parts. 2. Check the gears relating to engagement/disengagement of the Pressure Roller; replace the Fixing Assembly if damaged. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

• Code: 009-0501-05
• Description: Pressure Roller engagement/disengagement timeout error
• Causes: Engagement operation of the Pressure Roller was not completed within the specified period of time.
• Remedy: [Related parts] R1.00 - Harness connecting from the Fixing Feed Driver PCB (UN5/J1508) to the Fixing Pressure Release Sensor and Half Pressure Position Sensor (PS73/J7220 and PS110/J8033) - Harness between the Fixing Feed Driver PCB (UN5/J1507) and the Fixing Motor (M48/J7217) - Fixing Pressure Release Sensor (PS73) - Half Pressure Position Sensor (PS110) - Fixing Motor (M48) - Fixing Feed Driver PCB (UN5) - DC Controller PCB (UN2) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check/replace the related harness/cable, connector and parts. 2. Check the Pressure Release Cam; replace the Fixing Assembly if damaged. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

• Code: 012-0101-05
• Description: Drum speed detection error (Y)
• Causes: The Drum Speed Detection PCB (Y) 1/2 detected a rotation signal error.
• Remedy: [Related parts] R1.00 - Harness connecting from the Drum Driver PCB (UN6/J1905) to the Drum Speed Detection PCB (Y) 1/2 and Drum Motor (Y) (UN20/J7316, UN21/J7317 and M21/J7300) - Drum Speed Detection PCB (Y) 1/2 (UN20 and UN21) - Drum Motor (Y) (M21) - Drum Unit (Y) - Drum Driver PCB (UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check that the Encoder Wheel of the Drum Speed Detection PCB (Y) 1/2 is properly installed. 2. Clean the Drum Speed Detection PCB (Y) 1/2 and the Encoder Wheel. 3. Set the Drum Unit (Y) again. 4. Check/replace the related harness/cable, connector and parts.

• Code: 012-0102-05
• Description: Drum speed detection error (Y)
• Causes: The Drum Speed Detection PCB (Y) 1 detected a rotation signal error.
• Remedy: [Related parts] R1.00 - Harness connecting from the Drum Driver PCB (UN6/J1905) to the Drum Speed Detection PCB (Y) 1 and Drum Motor (Y) (UN20/J7316 and M21/J7300) - Drum Speed Detection PCB (Y) 1 (UN20) - Drum Motor (Y) (M21) - Drum Unit (Y) - Drum Driver PCB (UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Clean the Drum Speed Detection PCB (Y) 1 and the Encoder Wheel. 2. Set the Drum Unit (Y) again. 3. Check/replace the related harness/cable, connector and parts.

• Code: 012-0103-05
• Description: Drum speed detection error (Y)
• Causes: The Drum Speed Detection PCB (Y) 2 detected a rotation signal error.
• Remedy: [Related parts] R1.00 - Harness between the Drum Driver PCB (UN6/J1905) and the Drum Speed Detection PCB (Y) 2 (UN21/J7317) - Drum Speed Detection PCB (Y) 2 (UN21) - Drum Driver PCB (UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Clean the Drum Speed Detection PCB (Y) 2. 2. Check/replace the related harness/cable, connector and parts.

• Code: 012-0106-05
• Description: Drum Motor (Y) rotation error
• Causes: The Drum Motor (Y) is not rotating at the specified speed, or it is stopped.
• Remedy: [Related parts] R1.00 - Harness between the Drum Driver PCB (UN6/J1905) and the Drum Motor (Y) (M21/J7300) - Drum Motor (Y) (M21) - ITB Cleaning Blade - Drum Driver PCB (UN6) [Remedy] Perform the following in the order while checking whether the error is cleared. - Check that the Intermediate Transfer Belt is not displaced. - Check/replace the related harness/cable, connector and parts.