0

Các lỗi thường gặp

Code :
  • Code: C-1110
  • Description: Stapler assy/Rr abnormality. After the stapler motor /Rr (M30) starts operations, it does not complete operations within a specified period of time, and the stapler home sensor /Rr (PS40) does not turn ON. 35-0
  • Causes: Stapler assy FNS drive board (FNSDB: FS-521) FNS control board (FNSCB: FS-521)
  • Remedy: 1 Check the connector connection and the wiring between FNSDB and the stapler, and repair it if any abnormality. - 2 Check the connector connection and the wiring between FNSDB and FNSCB, and repair it if any abnormality. - 3 Replacing the stapler assy - 4 Replace FNSDB. - 5 Replace FNSCB.
  • Code: C-1113
  • Description: Rear stopper motor (M26) operation abnormality. After the home position search operation of M26 starts, the rear stopper home sensor (PS35) does not turn ON within a specified period of time. 35-1
  • Causes: Stapler rotation home sensor (PS14: FS-521) Rear stopper motor (M26: FS-521) FNS drive board (FNSDB: FS-521) FNS control board (FNSCB: FS-521)
  • Remedy: 1 Check the stapler rotation section, and clean/repair it if any abnormality. - 2 Check the connector connection and the wiring between FNSDB and motor/sensor, and repair it if any abnormality. - 3 Check the connector connection and the wiring between FNSDB and FNSCB, and repair it if any abnormality. - 4 Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. FS-521: 4-G 5 Check I/O and the operation of the sensor, and repair/replace it if any abnormality. FS-521: 2-G 6 Replace PS14. - 7 Replace M26. - 8 Replace FNSDB. - 9 Replace FNSCB.
  • Code: C-1140
  • Description: Paper exit arm motor (M23) operation abnormality. After the operation of M23 starts, the exit arm home sensor (PS9) does not turn ON within a specified period of time. Or, it operates for more than the allowed time at a speed out of the specified one. 35-1
  • Causes: Paper exit arm home sensor (PS9: FS-521) Paper exit arm motor (M23: FS-521) FNS drive board (FNSDB: FS-521) FNS control board (FNSCB: FS-521)
  • Remedy: 1 Check the paper exit arm section, and clean/repair it if any abnormality. - 2 Check the connector connection and the wiring between FNSDB and motor/sensor, and repair it if any abnormality. - 3 Check the connector connection and the wiring between FNSDB and FNSCB, and repair it if any abnormality. - 4 Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. FS-521: 6-G 5 Check I/O and the operation of the sensor, and repair/replace it if any abnormality. FS-521: 3-G 6 Replace PS9. - 7 Replace M23. - 8 Replace FNSDB. - 9 Replace FNSCB.
  • Code: C-1141
  • Description: Stack assist guide motor (M24) operation abnormality. After M24 starts operations, the stack assist home sensor (PS32) does not turn ON within a specified period of time. 35-1
  • Causes: Stack assist home sensor (PS32: FS-521) Stack assist guide motor (M24: FS-521) FNS drive board (FNSDB: FS-521) FNS control board (FNSCB: FS-521)
  • Remedy: 1 Check the stapler rotation section, and clean/repair it if any abnormality. - 2 Check the connector connection and the wiring between FNSDB and motor/sensor, and repair it if any abnormality. - 3 Check the connector connection and the wiring between FNSDB and FNSCB, and repair it if any abnormality. - 4 Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. FS-521: 5-G 5 Check I/O and the operation of the sensor, and repair/replace it if any abnormality. FS-521: 3-B 6 Replace PS32. - 7 Replace M24. - 8 Replace FNSDB. - 9 Replace FNSCB.
  • Code: C-1142
  • Description: Intermediate up and down roller operation abnormality. The Intermediate roller release solenoid (SD7) does not turn ON within a specified period of time after SD7 does not turn OFF within a specified period of time after the alignment motor /Fr and Rr/ (M22 and M5) turn OFF. Or, SD7 does not turn ON within a specified period of time after it turns OFF.
  • Causes: Intermediate roller home sensor (PS33: FS-521) Intermediate roller open close motor (M25: FS-521) FNS drive board (FNSDB: FS-521) FNS control board (FNSCB: FS-521)
  • Remedy: 1 Check the intermediate roller open close section, and clean/repair it if any abnormality. - 2 Check the connector connection and the wiring between FNSDB and motor/sensor, and repair it if any abnormality. - 3 Check the connector connection and the wiring between FNSDB and FNSCB, and repair it if any abnormality. - 4 Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. FS-521: 4-G 5 Check I/O and the operation of the sensor, and repair/replace it if any abnormality. FS-521: 3-G 6 Replace PS33. - 7 Replace M25. - 8 Replace FNSDB. - 9 Replace FNSCB.
  • Code: C-1143
  • Description: Conveyance operation abnormality. The conveyance motor (M1) does not turn ON when the start button is turned ON. Or the conveyance motor (M1) does not shift the speed for each processing. 35-1
  • Causes: Conveyance motor (M1: FS-521) FNS drive board (FNSDB: FS-521) FNS control board (FNSCB: FS-521)
  • Remedy: 1 Check the conveyance section, and clean/repair it if any abnormality. - 2 Check the connector connection and the wiring between FNSDB and the motor, and repair it if any abnormality. - 3 Check the connector connection and the wiring between FNSDB and FNSCB, and repair it if any abnormality. - 4 Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. FS-521: 1-B 5 Replace M1. - 6 Replace FNSDB. - 7 Replace FNSCB.
  • Code: C-1144
  • Description: Paper exit alignment motor /Fr (M15) abnormality The paper exit alignment plate home sensor /Fr (PS18) does not turn ON within a specified period of time after M15 starts the home position search operation. Or, even after a specified period of time after M15 starts the operation, it does not stop. 35-1
  • Causes: Paper exit alignment plate home sensor /Fr (PS18: FS-521) Paper exit alignment motor /Fr (M15: FS-521) FNS drive board (FNSDB: FS-521) FNS control board (FNSCB: FS-521)
  • Remedy: 1 Check the front side of the paper exit alignment section, and clean/repair it if any abnormality. - 2 Check the connector connection and the wiring between FNSDB and motor/sensor, and repair it if any abnormality. - 3 Check the connector connection and the wiring between FNSDB and FNSCB, and repair it if any abnormality. - 4 Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. FS-521: 8-G 5 Check I/O and the operation of the sensor, and repair/replace it if any abnormality. FS-521: 7-G 6 Replace PS18. - 7 Replace M15. - 8 Replace FNSDB. - 9 Replace FNSCB.
  • Code: C-1145
  • Description: Paper exit alignment motor /Rr (M14) abnormality The paper exit alignment plate home sensor /Fr (PS19) does not turn ON even after a specified period of time after M14 starts the home position search operation. Or, even after a specified period of time after M14 starts the operation, it does not stop. 35-1
  • Causes: Paper exit alignment plate home sensor /Rr (PS19: FS-521) Paper exit alignment motor /Rr (M14: FS-521) FNS drive board (FNSDB: FS-521) FNS control board (FNSCB: FS-521)
  • Remedy: 1 Check the rear side of the paper exit alignment section, and clean/repair it if any abnormality. - 2 Check the connector connection and the wiring between FNSDB and motor/sensor, and repair it if any abnormality. - 3 Check the connector connection and the wiring between FNSDB and FNSCB, and repair it if any abnormality. - 4 Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. FS-521: 7-G 5 Check I/O and the operation of the sensor, and repair/replace it if any abnormality. FS-521: 7-G 6 Replace PS19. - 7 Replace M14. - 8 Replace FNSDB. - 9 Replace FNSCB.
‹ First  < 37 38 39 40 41 42 43 >  Last ›
Thêm vào giỏ hàng thành công
popup

Số lượng:

Tổng tiền:

Danh mục