Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh Aficio MPC5002 — Trang 23/28

Code: 842

Description: Nand-Flash updating verification error A writing error for the module written in Nand-Flash occurs when the remote ROM and ROM are updating.
Causes: • Damaged Nand-Flash
Remedy: 1. Turn the main switch off and on.

Code: 850

Description: Network I/F error
Causes: • Inoperative
Remedy: 1. Turn the main switch off and on.

Code: 851

Description: IEEE1394 interface error
The 1394 interface is unusable.
Causes: • Defective IEEE1394 • Defective controller.
Remedy:

Code: 853

Description: Bluetooth device connection error (The Bluetooth interface unit was installed while the machine was turned on.)
Causes: The Bluetooth interface unit was installed while the machine was turned on.
Remedy: Turn off the main power switch, and then confirm that the Bluetooth interface unit was installed correctly. And then, turn on the main power switch again.

Code: 854

Description: Bluetooth device removed (The Bluetooth interface unit was removed while the machine was turned on.)
Causes: The Bluetooth interface unit was removed while the machine was turned on.
Remedy: Turn off the main power switch, and then confirm that the Bluetooth interface unit was installed correctly. And then, turn on the main power switch again.

Code: 855, 856

Description: Hardware Problem:wireless LAN board The wireless LAN board can be accessed, but an error was detected.
Causes: • Loose connection • Defective wireless LAN card
Remedy: 1. Make sure that the Wireless LAN connection is good 2. Replace the wireless LAN card.

Code: 858

Description: HDD Encryption unit error 1
A serious error occurs when data is encrypted to update an encryption key with the HDD encryption unit.
Causes: -00 Encryption key acquisition error: The controller fails to get a new encryption key. • Defective controller board 1. Replace the controller board. -01 Encryption key setting for HDD error: The controller fails to copy a new encryption key to the HDD. • Defective SATA chip on the controller board 1. Turn the machine power off and on. 2. If the error reoccurs, replace the controller board. -02 NVRAM data encryption error 1: An error occurs while the NVRAM data is encrypted. • Defective SATA chip on the controller board 1. Replace the NVRAM. -30 NVRAM data encryption error 2: An error occurs before the NVRAM data is encrypted. • Defective controller board 1. Turn the machine power off and on. 2. If the error reoccurs, replace the controller board. -31 Other error: A serious error occurs while the data is encrypted. Same as SC991
Remedy:

Code: 859

Description: HDD Encryption unit error 2
A serious error occurs when the HDD data is encrypted to update an encryption key with the HDD encryption unit.
Causes: -08 HDD check error: The HDD is not correctly installed. • No HDD installed • Unformatted HDD • The encryption key on the controller is different from the one on the HDD 1. Install the HDD correctly. 2. Initialize the HDD. -09 Power failure during the data encryption: The data encryption (NVRAM and HDD) has not been completed. • Power failure during the data encryption 1. Initialize the HDD. -10 Data read/write error: The DMAC error is detected twice or more. Same as SC863.
Remedy:
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie