Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh Aficio SP8200DN — Trang 3/14

Code: 372

Description: TD sensor adjustment error
Vts is less than 1.8V or 4.8V or more during TD sensor initialization
Causes: • Heat seal not removed from a new developer pack • TD harness sensor disconnected, loose or defective • TD sensor defective • Harness between TD sensor and drawer disconnected, defective

Code: 396

Description: Drum motor error
The machine detects a lock signal error from the drum motor for 2 seconds after the drum motor turned on.
Causes: • Overload on the motor • Defective drum motor • Defective harness • Defective IOB

Code: 400

Description: Vsg adjustment error
Vsg is more than 4.2V or 3.8V or less when the machine adjusts Vsg value.
Causes: • Dirty or defective ID sensor • Defective ID sensor shutter

Code: 440

Description: Transfer belt bias error
The feed back bias from the transfer belt is more than 4V for 60 msec while the transfer belt bias is output. The A/D conversion level is 20 or less for 60 msec. The PWM duty is 24% or more for 60 msec.
Causes: • Power pack broken • Defective harness • Disconnected connector

Code: 441

Description: Transfer/Development motor error
The machine detects a lock signal error from the transfer/development motor for 2 seconds after the transfer/development motor turned on.
Causes: • Overload on the motor • Defective transfer/development motor • Defective harness • Defective IOB

Code: 442

Description: Transfer belt contact motor error
The transfer belt HP sensor detects incorrect movement of the transfer belt after the transfer belt contact motor has turned on.
Causes: • Dirty transfer belt HP sensor • Defective transfer belt contact motor • Disconnected connector of the transfer belt HP sensor or motor • Disconnected cable • Defective IOB

Code: 501

Description: 1st tray lift malfunction
The tray lift sensor is not activated after the tray lift motor has been on for 10 seconds. If the main power switch is turned on when the paper is already at the feed height, the paper height position is detected again. At this time, the tray lift sensor should de-activate within 1.5 sec after the paper bottom plate starts to drop. If it does not deactivate within 1.5 sec., a message will prompt the user to reset Tray 1. After two attempts to release the error by re-setting the paper tray, if this does not solve the problem then this SC is displayed.
Causes: • An obstruction (jammed paper, paper scraps, etc.) has blocked the motor drive and caused an overload. • Tray lift sensor connection loose, disconnected, or damaged • Tray lift sensor defective • Tray lift motor connection loose, disconnected, or damaged • Tray lift motor defective

Code: 502

Description: 2nd tray lift malfunction
The tray lift sensor is not activated after the tray lift motor has been on for 10 seconds. If the main power switch is turned on when the paper is already at the feed height, the paper height position is detected again. At this time, the tray lift sensor should de-activate within 1.5 sec. after the paper bottom plate starts to drop. If it does not deactivate within 1.5 sec., a message will prompt the user to reset Tray 2. After two attempts to re-set the paper tray, if this does not solve the problem then this SC is displayed.
Causes: • An obstruction (jammed paper, paper scraps, etc.) has blocked the motor drive and caused an overload. • Tray lift sensor connection loose, disconnected, or damaged • Tray lift sensor defective • Tray lift motor connection loose, disconnected, or damaged • Tray lift motor defective
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie