Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Xerox WorkCentre 5022 — Trang 6/18

Code: 016-501

Description: Controller Boot Flash Write Error Unable to write the Download File of Controller Boot into the Flash ROM.
Remedy: 1. Turn the power OFF and ON. 2. If the problem persists, replace the ESS/MCU PWB (PL 18.3).

Code: 016-502

Description: UI Panel Download Flash Write Error Unable to write the Download File of UI Panel into the Flash ROM.
Remedy: 1. Turn the power OFF and ON. 2. If the problem persists, replace the following parts in sequence: • ESS/MCU PWB (PL 18.3) • UI PWB (PL 1.10)

Code: 016-504

Description: UI panel Font Download Flash Write Error Unable to write the Download File of UI Panel Font into the Flash ROM
Remedy: 1. Turn the power OFF and ON. 2. If the problem persists, replace the following parts in sequence: • Control Panel (PL 1.10) • ESS/MCU PWB (PL 18.3)

Code: 016-570

Description: No Response from USB-Host for Scan Job When any of the following has occurred as Scan to PC (USB) is in progress. • The command from the PC was disrupted for 5 seconds. • The machine has detected a communication error with the USB Device. • The sending of commands to the PC remained unsuccessful even when 500 ms has passed. (The time-out time is the time calculated from the size of the data being sent only when sending image data.)
Remedy: 1. Press [Stop] on the UI Panel. 2. Check the connection of the USB Cable between this machine and the PC. 3. Check the status (is it powered OFF, frozen, etc.) of the PC.

Code: 016-571

Description: No Response from USB-Host for Print Job When any of the following has occurred as USB Print or Download data interpretation is in progress. • The command from the PC was disrupted for 2 minutes. • The machine has detected a communication error with the USB Device. • The sending of commands to the PC remained unsuccessful even when 500 ms has passed. NOTE: This Fault will clear automatically. (It will not be displayed on the UI Panel)
Remedy: 1. Check the connection of the USB Cable between this machine and the PC. 2. Check the status (is it powered OFF, frozen, etc.) of the PC.

Code: 024-910, 024-911, 024-915

Description: Tray 1/Tray 2/MSI Paper Length Mismatch The Paper Size for the applicable Tray is longer by 10.1 mm or more, or shorter by 13.1 mm or more than the setting.
Remedy: Check the following: • Check whether the size of the paper loaded in the Tray is the same as the size of the Paper Guide. • Transportation failure due to foreign substance on the document path. • The surface of the Feed Roll, T/A Roll 2 (Tray 2), Regi Roll, and Idler Roll of the applicable Tray for foreign substances. • The surface of the Feed Roll, T/A Roll 2 (Tray 2), Regi Roll, and Idler Roll of the applicable Tray for wear. • The Regi Sensor (Input Check [071-105]) for operation failure. (PL 15.1) • The Regi Clutch (Output Check [071-001]) for operation failure. (PL 15.1) • The MSI Feed Clutch (Output Check [072-014]) for operation failure. (MSI) (PL 13.3) • The BTR for contamination, wear, and transportation failure due to deterioration. • The Drive Gear for wear and damage. • Usage of out of spec paper. If no problems are found, replace the ESS/MCU PWB (PL 18.3).

Code: 024-912

Description: Tray 3 Paper Length Mismatch The Paper Size for the applicable Tray is longer by 10.1 mm or more, or shorter by 13.1 mm or more than the setting.
Remedy: Check the following: • Check whether the size of the paper loaded in Tray 3 is the same as the size of the Paper Guide. • Transportation failure due to foreign substance on the document path. • The surface of the Feed Roll, T/A Roll (Tray 3), Regi Roll, and Idler Roll of the applicable Tray for foreign substances. • The surface of the Feed Roll, T/A Roll (Tray 3), Regi Roll, and Idler Roll of the applicable Tray for wear. • The Regi Sensor (Input Check [071-105]) for operation failure. (PL 15.1) • The Regi Clutch (Output Check [071-001]) for operation failure. (PL 15.1) • The MSI Feed Clutch (Output Check [072-014]) for operation failure. (MSI) (PL 13.3) • The BTR for contamination, wear, and transportation failure due to deterioration. • The Drive Gear for wear and damage. • Usage of out of spec paper. If no problems are found, replace the ESS/MCU PWB. (PL 18.3)

Code: 024-913

Description: Tray 4 Paper Length Mismatch The Paper Size for the applicable Tray is longer by 10.1 mm or more, or shorter by 13.1 mm or more than the setting.
Remedy: Check the following: • Check whether the size of the paper loaded in Tray 4 is the same as the size of the Paper Guide. • Transportation failure due to foreign substance on the document path. • The surface of the Feed Roll, T/A Roll (Tray 4), Regi Roll, and Idler Roll of the applicable Tray for foreign substances. • The surface of the Feed Roll, T/A Roll (Tray 4), Regi Roll, and Idler Roll of the applicable Tray for wear. • The Regi Sensor (Input Check [071-105]) for operation failure. (PL 15.1) • The Regi Clutch (Output Check [071-001]) for operation failure. (PL 15.1) • The MSI Feed Clutch (Output Check [072-014]) for operation failure. (MSI) (PL 13.3) • The BTR for contamination, wear, and transportation failure due to deterioration. • The Drive Gear for wear and damage. • Usage of out of spec paper. If no problems are found, replace the ESS/MCU PWB. (PL 18.3)
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie