• Code: 11-100-110
• Description: 2K LCSS Paper Entry RAP 11-100-110 The leading edge of the sheet is late to the entry sensor Q11-100.
• Remedy: NOTE: In diagnostics, actuating any 2K LCSS sensor or switch can change the displayed state on the UI. Make sure that the correct sensor or switch is tested. Lower the paper entry guide assembly, PL 11.14 Item 8, to access the entry sensor. Enter dC330, code 11-100. Actuate the entry sensor, Q11-100. The display changes. Y↓N→Go to Flag 1. Check Q11-100. Refer to: • 11G-110 2K LCSS PWB Damage RAP. • GP 11, How to Check a Sensor. • P/J304, 2K LCSS PWB. • 11D-110 2K LCSS Power Distribution RAP. Repair or install new components as necessary: • Entry sensor, PL 11.24 Item 3. • 2K LCSS PWB, PL 11.26 Item 1. Perform SCP 6 Final Actions.

• Code: 11-100-120
• Description: 1K LCSS Paper Entry RAP 11-100-110 The leading edge of the sheet is late to the entry sensor Q11-100.
• Remedy: Check the following: • 1K LCSS PWB DIP switch settings, refer to 11E-120 1K LCSS PWB DIP Switch Settings RAP. • Ensure the paper tray guides are set to the correct position for the size of paper in the tray. • Check the input guide for damage or wear that could cause paper to jam. • Paper jam in the machine to 1K LCSS paper path. • IOT exit path and feed rolls. • Feeding performance from a paper tray loaded with a new ream of paper. Procedure NOTE: In diagnostics, actuating any 1K LCSS sensor or switch can change the displayed state on the UI. Make sure that the correct sensor or switch is tested.. Lower the paper entry guide assembly, PL 11.110 Item 8, to access the entry sensor. Enter dC330, code 11-100, entry sensor, Q11-100. Actuate Q11-100. The display changes. Y↓N→Go to Flag 1. Check Q11-100. Refer to: • 11F-120 1K LCSS PWB Damage RAP. • GP 11 How to Check a Sensor. • P/J8, 1K LCSS PWB • 11C-120 1K LCSS Power Distribution RAP. Repair or install new components as necessary: • Entry sensor, PL 11.122 Item 3. • 1K LCSS PWB, PL 11.124 Item 1. Perform SCP 6 Final Actions.

• Code: 11-100-171, 11-101-171
• Description: HVF Entry Sensor RAP 11-100-171 The paper leading edge is late arriving at the entry sensor. 11-101-171 The paper trailing edge is late leaving the entry sensor.
• Remedy: shows the location of the components. Enter dC330, code 11-100. Manually operate the entry sensor, Q11-100. The display changes. Y↓N→Go to Flag 1. Check the sensor, Q11-100. Refer to: • GP 11 How to Check a Sensor. • P/J101, HVF Control PWB • 11A-171 HVF Power Distribution RAP Install new components as necessary: • Entry sensor, PL 11.156 Item 2. • HVF Control PWB, PL 11.157 Item 2. Enter dC330, code 11-000 to run the Entry feed motor 1, MOT 11-000. The motor runs. Y↓N→Go to Flag 2. Check the entry feed motor 1, MOT 11-000. Refer to: • GP 10 How to Check a Motor. • P/J102, HVF Control PWB • 11A-171 HVF Power Distribution RAP Install new components as necessary: • Entry feed motor 1, PL 11.150 Item 2. • HVF control PWB, PL 11.157 Item 2. Check the drive belt on the motor. The drive belt is good. Y↓N→Install a new drive belt, PL 11.150 Item 7. The fault may be intermittent, check for damaged wiring or bad connectors. If necessary install new components: • Entry sensor, PL 11.156 Item 2. • Entry feed motor 1, PL 11.150 Item 2. • HVF control PWB, PL 11.157 Item 2. • Check if the HVF module has the W/TAG V-006 modifications installed. If the modifications have not been installed perform ADJ 11.13-171 HVF Performance Improvements W/ TAG V-006.

• Code: 11-110-110
• Description: Sheet Late to Hole Punch RAP 11-110-110 Sheet late at the punch sensor.
• Remedy: NOTE: In diagnostics, actuating any 2K LCSS sensor or switch can change the displayed state on the UI. Make sure that the correct sensor or switch is tested.. Enter dC330, code 11-110. Actuate the punch sensor, Q11-110. The display changes. Y↓N→Go to Flag 1. Check Q11-110. Refer to: • 11G-110 2K LCSS PWB Damage RAP. • GP 11, How to Check a Sensor. • P/J307, 2K LCSS PWB. • 11D-110 2K LCSS Power Distribution RAP Repair or install new components as necessary: • Punch sensor, PL 11.6 Item 7. • 2K LCSS PWB, PL 11.26 Item 1. Perform SCP 6 Final Actions.

• Code: 11-130-110, 11-132-110
• Description: Paper Exiting to Bin 0 RAP 11-130-110 The leading edge of the sheet is late to the top exit sensor. 11-132-110 The trailing edge of the sheet is late from the top exit sensor.
• Remedy: NOTE: All 2K LCSS interlocks must be made to supply +24V to the motors. NOTE: In diagnostics, actuating any 2K LCSS sensor or switch can change the displayed state on the UI. Make sure that the correct sensor or switch is tested. Enter dC330, code 11-001 to run transport motor 2, MOT11-001. The motor runs. Y↓N→Go to Flag 3. Check MOT11-001. Refer to: • 11G-110 2K LCSS PWB Damage RAP. • GP 10, How to Check a Motor. • P/J309, 2K LCSS PWB. • 11D-110 2K LCSS Power Distribution RAP. Repair or install new components as necessary: • Transport motor 2, PL 11.22 Item 5. • 2K LCSS PWB, PL 11.26 Item 1. Enter dC330, code 11-002 to energize the diverter gate solenoid, S11-002. The diverter gate solenoid energizes. Y↓N→Go to Flag 2. Check SOL11-002. Refer to: • 11G-110 2K LCSS PWB Damage RAP. • GP 12, How to Check a Solenoid. • P/J306, 2K LCSS PWB. • 11D-110 2K LCSS Power Distribution RAP. Repair or install new components as necessary: • Diverter gate solenoid, PL 11.22 Item 12. • 2K LCSS PWB, PL 11.26 Item 1. Enter dC330, code 11-130, actuate the top exit sensor, Q11-130. The display changes. Y↓N→Go to Flag 1. Check Q11-130. Refer to: • 11G-110 2K LCSS PWB Damage RAP. • GP 11, How to Check a Sensor. • P/J313, 2K LCSS PWB. • 11D-110 2K LCSS Power Distribution RAP. Repair or install new components as necessary: • Top exit sensor, PL 11.22 Item 11. • 2K LCSS PWB, PL 11.26 Item 1. Enter dC330, code 11-000 to energize the transport motor 1, MOT 11-000. The motor energizes. Y↓N→Go to Flag 4. Check MOT 11-000. Refer to: • 11G-110 2K LCSS PWB Damage RAP. • GP 10, How to Check a Motor. • P/J305, 2K LCSS PWB. • 11D-110 2K LCSS Power Distribution RAP. Repair or install new components as necessary: • Transport motor 1, PL 11.14 Item 2. • 2K LCSS PWB, PL 11.26 Item 1. Perform SCP 6 Final Actions.

• Code: 11-130-120, 11-132-120
• Description: Paper Exiting to Bin 0 RAP 11-130-120 The leading edge of the sheet is late to the top exit sensor. 11-132-120 The trailing edge of the sheet is late from the top exit sensor.
• Remedy: NOTE: All 1K LCSS interlocks must be made to supply +24V to the motors. NOTE: In diagnostics, actuating any 1K LCSS sensor or switch can change the displayed state on the UI. Make sure that the correct sensor or switch is tested. Enter dC330, code 11-001 transport motor 2, MOT11-001. MOT11-001 runs. Y↓N→Go to Flag 3. Check MOT11-001. Refer to: • 11F-120 1K LCSS PWB Damage RAP. • GP 10, How to Check a Motor. • P/J16, 1K LCSS PWB. • 11C-120 1K LCSS Power Distribution RAP. Repair or install new components as necessary: • Transport motor 2, PL 11.120 Item 13. • 1K LCSS PWB, PL 11.124 Item 1. NOTE: The diverter gate solenoid remains energized for 5 seconds. Enter dC330, code 11-002 diverter gate solenoid, SOL11-002. SOL11-002 energizes. Y↓N→Go to Flag 2. Check SOL11-002. Refer to: • 11F-120 1K LCSS PWB Damage RAP. • GP 12, How to Check a Solenoid. • P/J13, 1K LCSS PWB • 11C-120 1K LCSS Power Distribution RAP. Repair or install new components as necessary: • Diverter gate solenoid, PL 11.118 Item 12. • 1K LCSS PWB, PL 11.124 Item 1. Enter dC330, code 11-130, top exit sensor, Q11-130. Actuate Q11-130. The display changes. Y↓N→Go to Flag 1. Check Q11-130. Refer to: • 11F-120 1K LCSS PWB Damage RAP. • GP 11, How to Check a Sensor. • P/J2, 1K LCSS PWB • 11C-120 1K LCSS Power Distribution RAP. Repair or install new components as necessary: • Top exit sensor, PL 11.118 Item 11. • 1K LCSS PWB, PL 11.124 Item 1. Enter dC330, code 11-000, transport motor 1, MOT11-000. MOT11-000 runs. Y↓N→Go to Flag 4. Check MOT11-000. Refer to: • 11F-120 1K LCSS PWB Damage RAP. • GP 10, How to Check a Motor. • P/J17, 1K LCSS PWB. • 11C-120 1K LCSS Power Distribution RAP. Repair or install new components as necessary: • Transport motor 1, PL 11.110 Item 2. • 1K LCSS PWB, PL 11.124 Item 1. Perform SCP 6 Final Actions.

• Code: 11-130-171, 11-132-171
• Description: HVF Top Exit Sensor RAP 11-130-171 The paper leading edge is late arriving at the top exit sensor. 11-132-171 The paper trailing edge is late leaving the top exit sensor.
• Remedy: shows the location of the components. Enter dC330, code 11-130. Manually operate the top exit sensor, Q11-130. The display changes. Y↓N→Go to Flag 1. Check the sensor, Q11-130. Refer to: • GP 11 How to Check a Sensor. • P/J101, HVF Control PWB • 11A-171 HVF Power Distribution RAP Install new components as necessary: • Top exit sensor, PL 11.156 Item 3. • HVF Control PWB, PL 11.157 Item 2 Enter dC330, code 11-002. Energize the exit diverter solenoid SOL 11-002. The solenoid energizes. Y↓N→Go to Flag 2. Check the solenoid, SOL 11-002. Refer to: • GP 12, How to Check a Solenoid or Clutch. • P/J102, HVF Control PWB • 11A-171 HVF Power Distribution RAP. Install new components as necessary: • Exit diverter solenoid, PL 11.150 Item 4. • HVF control PWB, PL 11.157 Item 2 Enter dC330, code 11-001 to run the exit feed motor 2, MOT 11-001. The motor runs. Y↓N→Go to Flag 3. Check the exit feed motor 2, MOT 11-001. Refer to: • GP 10 How to Check a Motor. • P/J102, HVF Control PWB • 11A-171 HVF Power Distribution RAP Install new components as necessary: • Exit feed motor 2, PL 11.150 Item 1. • HVF control PWB, PL 11.157 Item 2. Check the drive belt on the motor. The drive belt is good. Y↓N→Install a new drive belt, PL 11.150 Item 7. The fault may be intermittent, check for damaged wiring or bad connectors. If necessary install new components: • Top exit sensor, PL 11.156 Item 3. • Exit diverter solenoid, PL 11.150 Item 4. • Diverter gate, PL 11.153 Item 9. • Exit feed motor 2, PL 11.150 Item 1. • HVF control PWB, PL 11.157 Item 2.

• Code: 11-140-110, 11-142-110
• Description: Sheet Late to Bin 1 RAP 11-140-110 The leading edge of the sheet is late to the 2nd to top exit sensor, Q11-140. 11-142-110 The trailing edge of the sheet is late to the 2nd to top exit sensor, Q11-140.
• Remedy: NOTE: All 2K LCSS interlocks must be made to supply +24V to the motors. NOTE: In diagnostics, actuating any 2K LCSS sensor or switch can change the displayed state on the UI. Make sure that the correct sensor or switch is tested.. Enter dC330, code 11-001 to energize the transport motor 2, MOT11-001. The motor energizes. Y↓N→Go to Flag 3. Check MOT11-001. Refer to: • 11G-110 2K LCSS PWB Damage RAP. • GP 10, How to check a motor. • P/J309, 2K LCSS PWB. • 11D-110 2K LCSS Power Distribution RAP. Repair or install new components as necessary: • Transport motor 2, PL 11.22 Item 5. • 2K LCSS PWB, PL 11.26 Item 1. Enter dC330, code 11-002 to energize the diverter solenoid, S11-002. Energize the solenoid. The diverter solenoid energizes. Y↓N→Go to Flag 4. Check SOL11-002. Refer to: • 11G-110 2K LCSS PWB Damage RAP. • GP 12, How to Check a Solenoid or Clutch. • P/J306, 2K LCSS PWB. • 11D-110 2K LCSS Power Distribution RAP. Repair or install new components as necessary: • Diverter gate solenoid, PL 11.22 Item 12. • 2K LCSS PWB, PL 11.26 Item 1.. Enter dC330, code 11-140, actuate the 2nd to top exit sensor, Q11-140. The display changes. Y↓N→Go to Flag 1. Check Q11-140. Refer to: • 11G-110 2K LCSS PWB Damage RAP. • GP 11, How to Check a sensor. • P/J313, 2K LCSS PWB. • 11D-110 2K LCSS Power Distribution RAP. Repair or install new components as necessary: • 2nd to top exit sensor, PL 11.23 Item 4. • 2K LCSS PWB, PL 11.26 Item 1. Enter dC330, code 11-000 to energize the transport motor 1, MOT 11-000. The motor energizes. Y↓N→Go to Flag 2. Check MOT 11-000. Refer to: • 11G-110 2K LCSS PWB Damage RAP. • GP 10, How to Check a Motor. • P/J305, 2K LCSS PWB. • 11D-110 2K LCSS Power Distribution RAP. Repair or install new components as necessary: • Transport motor 1, PL 11.14 Item 2. • 2K LCSS PWB, PL 11.26 Item 1. If the fault is still present, perform 11-007-110, 11-008-110, 11-312-110, 11-313-110, 11-319- 110 Rear Tamper Move Failure RAP. NOTE: A software problem can cause the machine to incorrectly display the fault code 11-142- 110.