Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Canon iR Advance C3330i — Trang 9/38

Code: E196 000F

Description: Communication error. The number of read/write job data to the DCON EEPROM exceeded 100.
Remedy: [Remedy] Turn OFF and then ON the main power. [Reference] Data (device information) is reset by turning OFF and then ON the main power.

Code: E196 0100

Description: Communication error. The NACK (a negative reply sent by the reception side to the sending side) was received 3 times in communication from the DC Controller PCB (CPU) to the SCNR EEPROM.
Remedy: [Related parts] • Harness between the DC Controller PCB (UN04/J111) and the Y/M Laser Driver PCB (UN08/J202) (Unit of replacement: CABLE, CASSETTE SIZE) • Harness between the DC Controller PCB (UN04/J114) and the Secondary Transfer High Voltage PCB (UN03/J501) (Unit of replacement: CABLE, 2ND TRNSFR. H.V. PCB) • Y/M Laser Driver PCB (UN08) (Unit of replacement: LASER SCANNER ASSEMBLY) • Secondary Transfer High Voltage PCB (UN03) (Unit of replacement: 2ND TRNSFR. H.V. PCB ASS'Y) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Code: E196 0101

Description: Communication error. Although access to the SCNR EEPROM from the DC Controller PCB (CPU) was performed 3 times, no response was received and timeout occurred.
Remedy: [Related parts] • Harness between the DC Controller PCB (UN04/J111) and the Y/M Laser Driver PCB (UN08/J202) (Unit of replacement: CABLE, CASSETTE SIZE) • Harness between the DC Controller PCB (UN04/J114) and the Secondary Transfer High Voltage PCB (UN03/J501) (Unit of replacement: CABLE, 2ND TRNSFR. H.V. PCB) • Y/M Laser Driver PCB (UN08) (Unit of replacement: LASER SCANNER ASSEMBLY) • Secondary Transfer High Voltage PCB (UN03) (Unit of replacement: 2ND TRNSFR. H.V. PCB ASS'Y) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Code: E196 010F

Description: Communication error. The number of read/write job data to the SCNR EEPROM exceeded 100
Remedy: [Remedy] Turn OFF and then ON the main power. [Reference] Data (device information) is reset by turning OFF and then ON the main power.

Code: E196 0800

Description: Communication error. The NACK (a negative reply sent by the reception side to the sending side) was received 3 times in communication from the DC Controller PCB (CPU) to the HVT EEPROM.
Remedy: [Related parts] • Harness between the DC Controller PCB (UN04/J111) and the Y/M Laser Driver PCB (UN08/J202) (Unit of replacement: CABLE, CASSETTE SIZE) • Harness between the DC Controller PCB (UN04/J114) and the Secondary Transfer High Voltage PCB (UN03/J501) (Unit of replacement: CABLE, 2ND TRNSFR. H.V. PCB) • Y/M Laser Driver PCB (UN08) (Unit of replacement: LASER SCANNER ASSEMBLY) • Secondary Transfer High Voltage PCB (UN03) (Unit of replacement: 2ND TRNSFR. H.V. PCB ASS'Y) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Code: E196 0801

Description: Communication error. Although access to the HVT EEPROM from the DC Controller PCB (CPU) was performed 3 times, no response was received and timeout occurred.
Remedy: [Related parts] • Harness between the DC Controller PCB (UN04/J111) and the Y/M Laser Driver PCB (UN08/J202) (Unit of replacement: CABLE, CASSETTE SIZE) • Harness between the DC Controller PCB (UN04/J114) and the Secondary Transfer High Voltage PCB (UN03/J501) (Unit of replacement: CABLE, 2ND TRNSFR. H.V. PCB) • Y/M Laser Driver PCB (UN08) (Unit of replacement: LASER SCANNER ASSEMBLY) • Secondary Transfer High Voltage PCB (UN03) (Unit of replacement: 2ND TRNSFR. H.V. PCB ASS'Y) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES

Code: E196 080F

Description: Communication error. The number of read/write job data to the HVT EEPROM exceeded 100.
Remedy: [Remedy] Turn OFF and then ON the main power. [Reference] Data (device information) is reset by turning OFF and then ON the main power

Code: E197 0B11

Description: Serial communication error.Communication between the DC Controller PCB and the Second/ Third Delivery PCB was not completed.
Remedy: [Related parts] • Harness between the DC Controller PCB (UN04/J123) and the Second/Third Delivery Unit (J701) (Unit of replacement: CABLE, FEED) • Second/Third Delivery Unit (Unit of replacement: 2ND/3RD DELIVERY DRIVE ASS'Y) • DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. • Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP • Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie