Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Epson AcuLaser C9200N — Trang 10/11

Code: E621

Description: BLACK PC Drum sensor malfunction
- The output from the Black PC Drive Main and Sub Sensors remains unchanged for a continuous period of 1,000 ms while the Main Motor is turning stably and the Lock signal is active (LOW-0).
Causes: • Transport Drive Assy • Mechanical Control Board (PWB-M) • Harness
Remedy: 1 Check if the Detect Light Shield Plate has damages and is properly installed, and correct as necessary. - - 2 Check the Transport Drive Assy connector for proper connection and correct as necessary. - - 3 Check the PWB-M connector for proper connection and correct as necessary. - - 4 Change the cable that connects Transport Drive Assy and PWB-M. - - 5 Change Transport Drive Assy - - 6 Change PWB-M

Code: E630

Description: IDC Sensor (front) failure
- All outputs of Sensor photo-receiver section from the detection point (unprinted surface on the Image Transfer Belt) are 0.5 V or less, or 4.3 V or more at output checking during IDC Sensor adjustment.
- All outputs of Sensor photo-receiver section from the detection point (unprinted surface on the Image Transfer Belt) are 1.9 V or less, or 4.4 V or more at density setting during IDC Sensor adjustment.
- The output of Sensor photo-receiver section from the detection point (toner pattern on the Image Transfer Belt) is 1.0 V or less after the adjustment.
Causes: IDC Sensor
Remedy: 1 Check that the IDC Sensor is properly installed and correct as necessary. - - 2 Check if the IDC sensor is dirty and correct as necessary. - - 3 Check the IDC Sensor connector for proper connection and correct as necessary. - - 4 Check the PWB-M connector for proper connection and correct as necessary. - - 5 Change the cable that connects IDC Sensor and PWB-M. - - 6 Change the IDC Sensor.

Code: E631

Description: IDC Sensor (back) failure
- All outputs of Sensor photo-receiver section from the detection point (unprinted surface on the Image Transfer Belt) are 0.5 V or less, or 4.3 V or more at output checking during IDC Sensor adjustment.
- All outputs of Sensor photo-receiver section from the detection point (unprinted surface on the Image Transfer Belt) are 1.9 V or less, or 4.4 V or more at density setting during IDC Sensor adjustment.
- The output of Sensor photo-receiver section from the detection point (toner pattern on the Image Transfer Belt) is 1.0 V or less after the adjustment.
Causes: IDC Sensor
Remedy: 1 Check that the IDC Sensor is properly installed and correct as necessary. - - 2 Check if the IDC sensor is dirty and correct as necessary. - - 3 Check the IDC Sensor connector for proper connection and correct as necessary. - - 4 Check the PWB-M connector for proper connection and correct as necessary. - - 5 Change the cable that connects IDC Sensor and PWB-M. - - 6 Change the IDC Sensor.

Code: E640

Description: Color Shift Test Pattern failure
- The number of points detected in the main scan direction is more or less than the specified value during main scan direction registration correction.
- The number of points detected in the sub scan direction is more or less than the specified value during sub scan direction registration correction.
Causes: • Transfer Belt Unit • IDC Sensor • Photoconductor Unit • PH Unit
Remedy: 1 Check if Transfer Belt has damages and correct as necessary. - - 2 Check that the IDC Sensor is properly installed and correct as necessary. - - 3 Check if the IDC sensor is dirty and correct as necessary. - - 4 Check the IDC Sensor connector for proper connection and correct as necessary. - - 5 Check the PWB-M connector for proper connection and correct as necessary. - - 6 Change the cable that connects IDC Sensor and PWB-M. 7 Change IDC Sensor. 8 Change Photoconductor Unit. 9 Change PH Unit.

Code: E641

Description: Color Shift Adjust failure
- The color shift amount is greater than the specified range during main scan direction registration correction.
- The color shift amount is greater than the specified range during sub scan direction registration correction.
- The skew correction amount is greater than the specified value.
Causes: • PH Unit (displacement) • Transfer Belt Unit
Remedy: 1 Execute the correction of skew. - - 2 Check if Transfer Belt has damages and correct as necessary.

Code: E701

Description: MP tray Rise Descent Error
- The Bypass Lift-Up Sensor is not blocked even when the Vertical Transport Motor has turned for a given number of pulses after the sequence to move the Paper Lifting Plate from the standby position to the feed position was started.
- The Bypass Lift-Up Sensor is not unblocked even when the Vertical Transport Motor has turned for a given number of pulses after the sequence to move the Paper Lifting Plate from the feed position to the standby position was started.
Causes: • MP tray Lift-up Sensor (PC14) • Vertical Transport Motor (M2-PC) • Control Board (PWB-Z-PC)
Remedy: 1 Check the M2-PC connector for proper connection and correct as necessary. - - 2 Check the connector of M2-PC for proper drive coupling and correct as necessary. - - 3 PC14 I/O check, Sensor check PWB-M CNTRY1-10 (ON) C-10 4 M2-PC operation check PWB-Z PJ5Z PC-5~8 Q-22 5 Change PWB-Z-PC.

Code: E702

Description: Standard cassette Elevator failure
- The Lift-Up Sensor is not blocked even after the lapse of a given period of time after the lifting motion has been started.
Causes: • Lift-up Sensor (PC7-PC) • Lift-up Sensor (PC7-PC) • Control Board (PWB-Z-PC)
Remedy: 1 Check the M3-PC connector for proper connection and correct as necessary. - - 2 Check the connector of M3-PC for proper drive coupling and correct as necessary. - - 3 PC7-PC I/O check, Sensor check PWB-Z PJ6Z PC-3 (ON) PWB-Z PJ4Z PC-4 to 5 V-21 to 22 4 M3-PC operation check Q-24 5 Change PWB-Z-PC.

Code: E703

Description: Optional Cassette1 Elevator failure
- The Lift-Up Sensor is not blocked even after the lapse of a given period of time after the lifting motion has been started.
Causes: • Lift-up Sensor (PC7-PC) • Lift-up Sensor (PC7-PC) • Control Board (PWB-Z-PC)
Remedy: 1 Check the M3-PC connector for proper connection and correct as necessary. - - 2 Check the connector of M3-PC for proper drive coupling and correct as necessary. - - 3 PC7-PC I/O check, Sensor check PWB-Z PJ6Z PC-3 (ON) PWB-Z PJ4Z PC-4 to 5 V-21 to 22 4 M3-PC operation check Q-24 5 Change PWB-Z-PC.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie