Remedy: • Open the Window and check for any visible obstacles restricting the movement of the Drive Roller. If there is a wrinkled mass of media inside the paper path, lift the Pinchwheels (using the Media Lever) and clear the obstruction. • Perform the gMedia Driveh Diagnostic () to further troubleshoot the error code. • If the System Error continues, replace the Media-Axis Motor .
Description: It was impossible to correctly stop the servo before setting the encoder position.
Remedy: • Open the Window and check for any visible obstacles restricting the movement of the Drive Roller. If there is a wrinkled mass of media inside the paper path, lift the Pinchwheels (using the Media Lever) and clear the obstruction. • Perform the gMedia Driveh Diagnostic () to further troubleshoot the error code. • If the System Error continues, replace the Media-Axis Motor .
Remedy: • Open the Window and check for any visible obstacles restricting the movement of the Carriage Assembly. If there is a wrinkled mass of media inside the paper path, lift the Pinchwheels (using the Media Lever) and clear the obstruction. • Check that the Carriage Stopper is correctly installed (Refer to Carriage Disassembly Instructions , step <cross reference>22.). • Perform the gScan-Axish Diagnostic () to further troubleshoot the error code. • Clean the Encode Strip using a lint free cloth dampened with water. • Check the cables are correctly connected between the PrintMech PCA and the Scan Axis Motor. • If the System Error continues, replace the Scan-Axis Motor .
Remedy: • Open the Window and check for any visible obstacles restricting the movement of the Carriage Assembly. If there is a wrinkled mass of media inside the paper path, lift the Pinchwheels (using the Media Lever) and clear the obstruction. • Replace the Encoder Strip and Encoder Sensor .
Description: This error is displayed when there is a need for the customer to clean the Encoder Strip. Full cleaning instructions come with the User’s Maintenance Kit. This message is displayed after a predefined quantity of ink has been consumed by the printer. At the time of firmware revison 7.0.0.3 the quantity of ink used before the 87:01 message is displayed is 10 liters.
Remedy: • Clean the Encoder Strip using a lint free cloth dampened with tap water, then reset the counter. (Setup > Resets > Encoder cleaning) Ë See the instructions provided in the User Maintenance Kit (P/N Q6715A). Refer to NOTE: This operation is a standard maintenance procedure for the customer. It is fully documented in the User Maintenance Kit. If the User Maintenance Kit is not available the customer must purchase another kit (Q6715A).
Description: The HP Instant Support troubleshooting tool has detected that at least one Printhead has been replaced without having a specific error, and without being recovered/cleaned.
Remedy: Advise the customer that the next time they want to replace a Printheads they should make sure that at least a Printhead Recovery is performed.
Remedy: • Remove ALL the Ink Cartridges and reinstall them one by one in to the Printer. • Replace the Ink Cartridges. • Replace the APS Assembly . • If the System Error continues, replace the Ink Supply Tubes and Trailing Cable . NOTE: If the Ink Supply Tubes are to be replaced, the Ink Cartridges need to be checked beforehand to see if they are capable of purging the new tubes, if they are not, new Ink Cartridges must also be sent with the parts to be replaced. To check the Ink Cartridges go to .
Nhận ưu đãi sớm nhất khi chương trình diễn ra
Đăng ký nhận bản tin
Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này.
Chính sách cookie
Những cookie này là cần thiết để trang web hoạt động đúng cách.
Những cookie này giúp chúng tôi hiểu cách khách truy cập tương tác với trang web.
Những cookie này được sử dụng để cung cấp quảng cáo cá nhân hóa.