Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh Aficio SP8100DN — Trang 4/15

Code: 440

Description: Main motor error
A main motor lock signal was not detected within 2 sec. after the main motor turned on.
Causes: • Main motor overload A main motor lock signal was not detected • Main motor drive board defective

Code: 442

Description: New PCU error
The new unit detection sensor switched ON for 2 sec. to detect a new PCU while the main motor was operating but the sensor did not go OFF.
Causes: • New unit detection sensor defective • New PCU defective Note: Normally the new unit detection sensor goes on after a new PCU is installed and then goes off after the ID sensor and TD sensor have been initialized.

Code: 450

Description: Feed Development Motor Error
The PLL lock signal remained LOW for 2 s while the feed development motor was operating.
Causes: • Motor lock caused by overload. • Motor drive board defective.

Code: 490

Description: Exhaust fan motor lock
An exhaust fan motor lock signal was not detected within 5 sec. after the exhaust fan motor turned on.
Causes: • Fan motor overloaded due to an obstruction • Exhaust fan motor connector or harness loose, broken, defective

Code: 492

Description: PCB cooling fan motor lock
A lock signal for the PCB cooling fan motor lock signal was not detected within 5 seconds after the cooling fan motor turned on.
Causes: • Fan motor overloaded due to an obstruction. • Fan motor connector or harness loose, broken, defective

Code: 501

Description: 1st tray lift malfunction
The paper height sensor did not activate after the tray lift motor was on for 10 sec. Note: Normally, if the power switch is turned on when the paper is already at the feed height, the paper height position is detected again. At this time, the paper height sensor should de-activate within 5 sec. after the paper bottom plate starts to drop. If it does not deactivate within 5 sec. after four attempts, a message will prompt the user to reset Tray 1. After two attempts to release the error by re-setting the paper tray, if this does not solve the problem then this SC is displayed.
Causes: • Lift motor connector or harness loose, broken, defective. • Lift motor defective • Height sensor connector or harness loose, broken, defective • Height sensor defective • Loose paper or other obstruction between the tray and motor • Pick-up solenoid connector or harness loose, broken, or defective • Pick-up solenoid defective

Code: 502

Description: 2nd tray lift malfunction
The paper height sensor did not activate after the tray lift motor was on for 10 sec. Note: Normally, if the power switch is turned on when the paper is already at the feed height, the paper height position is detected again. At this time, the paper height sensor should de-activate within 5 sec. after the paper bottom plate starts to drop. If it does not deactivate within 5 sec. after four attempts, a message will prompt the user to reset Tray 1. After two attempts to release the error by re-setting the paper tray, if this does not solve the problem then this SC is displayed.
Causes: • Lift motor connector or harness loose, broken, defective. • Lift motor defective • Height sensor connector or harness loose, broken, defective • Height sensor defective • Loose paper or other obstruction between the tray and motor • Pick-up solenoid connector or harness loose, broken, or defective • Pick-up solenoid defective

Code: 503

Description: 3rd tray lift malfunction (optional paper tray unit)
The paper height sensor is not activated after the tray lift motor has been on for 13 seconds. Note: Normally, if the power switch is turned on when the paper is already at the feed height, the paper height position is detected again. At this time, the paper height sensor should de-activate within 5 seconds after the paper bottom plate starts to drop. If it does not deactivate within 5 s after four attempts, the tray lift motor halts. After two attempts to re-set the paper tray, if this does not solve the problem, then this SC is displayed and tray control halts.
Causes: • Lift motor connector or harness loose, broken, defective. • Lift motor defective • Height sensor connector or harness loose, broken, defective • Height sensor defective
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie