Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Xerox Phaser 6128 MFP — Trang 2/7

Code: -09

Description: Front Cover Open Close Front Cover The Interlock Switch indicates the Front Cover is open. The following troubleshooting procedure applies to this error.
Causes: • Front Cover, PL1.1.8 • Interlock Harness, PL10.6.4 • LVPS, PL10.6.16 • MCU Board, PL10.7.7 • LVPS Main Harness, PL10.8.14
Remedy: 1 Check Interlock Switch operation. Run the Interlock Switch test (DI-07). Does the Switch operate? Replace the MCU Board. Go to step 2. 2 Check the Interlock Harness connections P/J14 and P/J501. Are the connections secure? Go to step 3. Secure the connections. 3 Check continuity of the LVPS Main Harness. Disconnect P/J14 from the MCU Board and P/J501 from the LVPS. Is the harness damaged? Repair the harness. Go to step 4. 4 Check for +24 V on P44 of the LVPS. Is there +24 V between P44-1 <=> ground? Go to step 5. Replace the LVPS. 5 Check the Interlock Switch signal. Does the voltage between P44-3 <=> ground change when the switch is closed? Replace the LVPS. Replace the Interlock Harness. 6 Replace the Interlock Switch Harness. Does the error persist? Replace the MCU Board. Complete.

Code: -10

Description: Side Door Open Close Side Door The Right Side Door Switch indicates the Right Side Door is open. The following troubleshooting procedure applies to this error.
Causes: • Right Side Cover, PL1.1.7 • Right Side Door Switch, PL5.1.9 • Side Switch harness, PL5.1.27 • MCU Board, PL10.7.7
Remedy: 1 Check Right Side Door Switch operation. Run the Side Switch test (DI-06). Does the switch operate? Replace the MCU Board. Go to step 2. 2 Check the Side Switch Harness connections P/J29 and P/J291. Are the connections secure? Go to step 3. Secure the connections. 3 Check continuity of the Side Switch Harness. Disconnect P/J29 from the MCU Board and P/J291 from the switch. Is the harness damaged? Repair the harness. Go to step 4. 4 Replace the Right Side Door Switch. Does the error persist? Replace the MCU Board. Complete.

Code: -11

Description: Scanner ADF Cover R Open The sensor at the ADF rear cover indicates the cover is open. This troubleshooting procedure applies to this error.
Causes: • Image Processor Board, PL10.6.6 • ADF Assembly, PL10.10.1
Remedy: 1 Check the ADF rear cover. Is the cover installed correctly and undamaged? Go to step 2. Repair or replace the ADF. 2 Check the connector P/J1003 on the I/P Board. Is the connection secure? Go to step 3. Secure the connector. 3 Replace the ADF Assembly. Does the error persist? Replace the I/P Board. Complete.

Code: -12

Description: Check Unit CTD Sensor Error The ADC Sensor has detected a density error for the indicated color. This troubleshooting procedure applies to this error.
Causes: • Transfer Belt, PL6.1.7 • Left Side Harness, PL10.4.18 • MCU Board, PL10.7.7
Remedy: 1 Check the Transfer Belt installation. Is the Transfer Belt correctly installed? Go to step 3. Reseat the Transfer Belt. Go to step 2. 2 Does the error still occur when the printer is turned On? Go to step 3. Complete. 3 Check connectors P/J28 and P/J281 between the MCU Board and Transfer Belt. Are the connectors secure? Go to step 4 Reconnect the connectors. 4 Check Left Side Harness continuity. Disconnect P/J28 from the MCU Board and P/J281 to the Transfer Belt. Is the harness damaged? Repair or replace the harness (PL10.4.18). Go to step 4. 5 Replace the Transfer Belt. Does the error persist? Replace the MCU Board. Complete.

Code: -13

Description: Memory Errors A memory access error occurred. This troubleshooting procedure applies to these errors.
Causes: • Image Processor Board, PL10.6.6
Remedy: 1 Check the Image Processor Board for correct installation. Is the Image Processor Board correctly installed? Go to step 2. Reseat connections on the Image Processor Board. 2 Does the error still occur when the printer is turned On? Replace the Image Processor Board. Complete.

Code: -14

Description: Copier Error Last Sheet not Copied An error in the imaging subsystem was detected. The following troubleshooting procedure applies to this error.
Causes: • Image Processor Board, PL10.6.6
Remedy: 1 Does the error message disappear within 70 seconds automatically, or disappear after pressing the OK button? Go to step 2. Go to step 4. 2 Does the error persist when copying, faxing, or scanning? Go to step 3. To to step 4. 3 Print a Configuration page: System > Information Pages > Configuration. Does the error persist when copying, faxing, or scanning? Go to step 4. Complete. 4 Cycle system power. Does the error persist? Replace the Image Processor Board. Complete.

Code: 003-340

Description: MCU Firmware Error MCU firmware error has occurred. This troubleshooting procedure applies to this error.
Causes: • MCU Board, PL10.7.7
Remedy: 1 Check the MCU Board installation. Cycle system power. Does the error persist? Replace the MCU Board. Check system electrical grounds.

Code: 010-317

Description: Reseat Fuser Error Warning Allow the Fuser to cool before removal. The Fuser has failed. This troubleshooting procedure applies to this error.
Causes: • Fuser, PL6.1.1 • MCU Board, PL10.7.7 • Fuser Harness, PL10.8.6
Remedy: 1 Check the connectors P/J17 and P/J171 between the MCU Board and the Fuser. Are the connectors secure? Go to step 2. Reconnect the connectors. 2 Check the Fuser harness for continuity. • Disconnect P/J17 from the MCU Board. • Disconnect P/J171 from the Fuser. • Disconnect P/J47 from the LVPS. • Check continuity between P/J17 and P/J47 <=> P/J171. Is the harness damaged? Go to step 3. Repair the Fuser harness. 3 Check the Fuser temperature sensor resistance at these pins on the Fuser connector J171: • J171-5 <=> J171-4 • J171-6 <=> J171-8 • J171-6 <=> J171-7 Is there a measurable resistance between each pair of pins? Replace the MCU Board. Go to step 4. 4 Replace the Fuser. Does the error persist? NOTE Reset the Fuser life counter after installation of a new Fuser. Replace the MCU Board. Complete.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie