Code :

Code: F137
Description: Finisher Backup RAM Failure An error was detected in the Finisher’s backup RAM.
Causes: • Finisher Control Board • Finisher Interconnect Cable • Engine Control Board, PL1.1.4
Remedy: 1 Check the following for evidence of fault or damage: • Finisher Interconnect Cable • Finisher connections Is there any damage? Replace any damaged parts. Go to Step 2. 2 Check all the pins of the Finisher Interconnect Cable for continuity. Is the cable conductive? Go to Step 3. Replace the cable. 3 Check all the pins of the OPTIF Harness for continuity. Is the harness conductive? Go to Step 4. Replace the OPTIF harness. 4 Replace the Finisher Control Board. Does the error persists? Replace the Engine Control Board Complete.

Code: F138
Description: Finisher Punch Backup RAM Failure An error was detected in the Punch Unit’s backup RAM.
Causes: • Punch Control Board
Remedy: 1 Check the Punch Control Board connections. Are P/J2003 and P/J2004 connected? Go to Step 2. Reseat or reconnect the harness. 2 Cycle printer power. Does the error persist? Replace the Punch Control Board. Complete.

Code: F139
Description: Finisher Punch Dust Sensor Failure An error was detected in the Punch Waste Sensor.
Causes: • Punch Box Sensor Emitter Board • Punch Box Sensor Receiver Board
Remedy: 1 Test the Punch Box Sensor. Run the Service Diagnostics Punch Box Set Sensor test. Does the sensor state change when the emitter is blocked? Go to Step 6. Go to Step 2. 2 Check the Punch Box Sensor Harness connection. Is P/J1005 connected to the Punch Control Board? Are P/J2005 and P/J2006 connected to the Emitter and Receiver boards? Go to Step 3. Connect the harness. 3 Check the Punch Box Sensor Harness continuity. Is the harness conductive? Go to Step 4. Replace the harness. 4 Check the Punch Box Sensor Emitter Board. Is the LED illuminated? Go to Step 5. Replace the Punch Box Emitter Board. 5 Check for +5 V to the Punch Box Sensor. Disconnect P/J2006. Is there +5 V at J2006-1 <=> J2006-2? Replace the Punch Box Sensor Receiver Board. Replace the Punch Control Board. 6 Replace the Finisher Control Board. Does the error still occur? Replace the Engine Control Board. Complete.

Code: F141
Description: Printer Error - Contact Service; report fault [n] The following procedures apply to codes associated with the Printer Error message.
Causes: • Punch • Punch Control Board
Remedy: 1 Replace the Punch. Cycle printer power. Does the error persist? Replace the Engine Control Board NVRAM. If the error persists, replace the Engine Control Board. Complete.

Code: F142
Description: Finisher Staple Unit Counter at End of Life
Causes: • Stapler
Remedy: 1 Replace the Stapler. Cycle printer power. Does the error persist? Replace the Engine Control Board NVRAM. If the error persists, replace the Engine Control Board. Complete.

Code: F181
Description: Finisher Punch Unit Transfer Motor Failure An error was detected in the Punch Transfer Motor.
Causes: • Punch Transfer Motor • Punch Control Board • Inverter Power Supply
Remedy: 1 Test the Punch Transfer Motor. 1. Close the Interlock Switches for test. 2. Run the Service Diagnostics Transfer Motor test. Does the motor operate? Complete. Go to Step 2. 2 Check for +24 V to the Punch Transfer Motor. Disconnect P/J2001. Is the +24 V across J2001-1 <=> ground? Replace the Punch Transfer Motor. Go to Step 3. 3 Check Punch Control Board for 24 V. 1. Disconnect P/J1001 on the Punch Control Board. Is the +24 V across P1001 pins 1 and 2? Replace the Punch Transfer Motor Harness. Replace the Punch Control Board. If the error persists, go to Step 4. 4 Check all pins of the Inverter Interface Cable for continuity. Disconnect CN1 and CN2 from the Finisher Control Board and the opposite end from the Inverter. Is the cable conductive? Replace the Inverter Power Supply. If the error persists, replace the Finisher Control Board. Replace the cable.

Code: F186
Description: Finisher Interface Error
Causes: • Finisher Control Board • Finisher Interconnect Cable • Engine Control Board, PL1.1.4
Remedy: 1 Check the following for evidence of fault or damage: • Finisher Interconnect Cable • Finisher connections Is there any damage? Replace any damaged parts. Go to Step 2. 2 Check all the pins of the Finisher Interconnect Cable for continuity. Is the cable conductive? Go to Step 3. Replace the cable. 3 Check all the pins of the OPTIF Harness for continuity. Is the harness conductive? Go to Step 4. Replace the OPTIF harness. 4 Replace the Finisher Control Board. Does the error persists? Replace the Engine Control Board Complete.

Code: F93
Description: Finisher Jog Motor Failure An error was detected in either the Front or Rear Alignment Motor.
Causes: • Paddle Assembly • Alignment Motors
Remedy: 1 Check the following for evidence of fault or damage: • Paddle Assembly • Alignment Motors Is there any damage? Replace any damaged parts. Go to Step 2. 2 Test the Alignment Plate Sensors. Run the Service Diagnostics Front and Rear Alignment Plate Sensor tests. Do the sensors function correctly? Replace the Paddle Assembly, Replace the sensor.