• Code: F111
• Description: Finisher Stack Handling Motor Failure The Delivery Belt Home Position Sensor detected a Stack Handling error.
• Causes: • Finisher Stack Handling Motor • Finisher Control Board
• Remedy: 1 Check the delivery mechanism. Does the Delivery Belt turn freely when operated manually? Go to Step 2. Repair the mechanism. 2 Test the Delivery Belt Home Position Sensor. Run the Service Diagnostics Exit Belt Home Position Sensor test. Does the sensor operate? Go to Step 3. Replace the sensor. If the error persists, go to Step 3. 3 Test the Staple Motor. 1. Close the Interlock Switches for test. 2. Run the Service Diagnostics Staple Motor tests. Does the motor operate? Replace the Finisher Control Board. If the error persists, go to Step 4. Go to Step 4. 4 Check for +24 V to the Staple Motor. Disconnect CN59. Is there +24 V across CN59-1 and -2 <=> ground? Replace the Stack Handling Motor. Replace the harness. If the error persists, go to Step 5. 5 Check all pins of the Inverter Interface Cable for continuity. Disconnect CN1 and CN2 from the Finisher Control Board and the opposite end from the Inverter. Is the cable conductive? Replace the Inverter Power Supply. Replace the cable.

• Code: F115
• Description: Finisher Lift Motor Failure The Paper Surface, Upper Limit, or Lift Motor Clock Sensor detected a Lift Motor error.
• Causes: • Upper Tray Lift Motor • Finisher Control Board • Inverter Power Supply
• Remedy: 1 Test each of these sensors. • Paper Surface Sensor • Tray Upper Limit Sensor • Shift Motor Clock Sensor Run the appropriate Service Diagnostics sensor test. Do all sensors function correctly? Go to Step 2. Replace the sensor. If the error persists, go to Step 2. 2 Check the tray lift mechanism. Does the mechanism move freely? Go to Step 5. Repair the lift mechanism. 3 Test the Lift Motor. 1. Close the Interlock Switches for test. 2. Run the Service Diagnostics Shift Motor test. Does the motor operate? Go to Step 8. Replace the motor. If the error persists, go to Step 6. 4 Check for +24 V to the Lift Motor. Disconnect CN70. Is there +24 V across CN70-1 and -2 <=> ground when the test is executed? Replace the Lift Motor. Replace the Finisher Control Board. If the error persists, go to Step 5. 5 Check all pins of the Inverter Interface Cable for continuity. Disconnect CN1 and CN2 from the Finisher Control Board and the opposite end from the Inverter. Is the cable conductive? Replace the Inverter Power Supply. Replace the cable.

• Code: F116
• Description: Finisher Exit Failure The Delivery Belt Home Position Sensor detected a Delivery Motor error.
• Causes: • Finisher Delivery Motor • Finisher Control Board
• Remedy: 1 Test the Exit Motor. 1. Close the Interlock Switches for test. 2. Run the Service Diagnostics Finisher Bundle Motor tests. Does the motor operate? Complete. Go to Step 2. 2 Check for +24 V to the Exit Motor. Disconnect CN59. Is the +24 V across CN59-1 and -2 <=> ground? Replace the Exit Motor. Go to Step 3. 3 Check Finisher Control Board for +24 V. 1. Disconnect CN13 on the Finisher Control Board. Is the +24 V across CN13-1 and -2? Replace the Exit Motor Harness. Replace the Finisher Control Board. If the error persists, go to Step 4. 4 Check the Inverter Interface Cable for continuity. Disconnect CN1 and CN2 from the Finisher Control Board and the opposite end from the Inverter. Is the cable conductive? Replace the Inverter Power Supply. Replace the cable.

• Code: F130
• Description: Controller to Engine Communications Failure An communications error was detected.
• Causes: • Engine Control Board, PL1.1.4
• Remedy: 1 Cycle power to the printer. Does the error persist? Go to Step 2. Complete 2 Reseat the CUIF connector. Does the error persist? Replace the Engine Control Board. If the error persists, replace the Image Processor Board Complete

• Code: F131
• Description: Finisher Fold Position Sensor Failure An error was detected with the Fold Position Sensor.
• Causes: • Fold Position Sensor • Finisher Control Board
• Remedy: 1 Test the Folding Position Sensor. Run the Service Diagnostics Bookbinding Position Sensor test. Does the sensor function correctly? Replace the Finisher Control Board. Go to Step 2. 2 Check the sensor connection. Is CN39 connected? Go to Step 3. Reconnect the sensor. 3 Replace the sensor. Does the error persist? Go to Step 4. Complete 4 Check all pins on the harness for continuity. Is the harness conductive? Replace the Finisher Control Board. Replace the harness.

• Code: F132
• Description: Finisher Punch Communications Failure An communications error occurred with the Punch Unit.
• Causes: • Finisher Control Board • Punch Control Board
• Remedy: 1 Check the connection between the Finisher and Punch Controller Boards. Are CN12 and CN14 on the Finisher Control Board connected? Are P/J2003 and P/J2004 on the Punch Control Board connected? Go to Step 2. Connect the harness. 2 Check all the pins of the harness for continuity. Is the cable conductive? Go to Step 3. Replace the harness. 3 Check for +24 V at the Finisher Control Board. Is there +24 V at CN14-5 <=> CN14-3? Replace the Punch Control Board. Replace the Finisher Control Board.

• Code: F133
• Description: Finisher Punch Side Registration Sensor Failure An error was detected in the Punch Side Registration Sensor.
• Causes: • Side Registration Emitter Board • Side Registration Receiver Board • Punch Control Board • Finisher Control Board
• Remedy: 1 Test the Side Registration Sensor. Run the Service Diagnostics Side Registration Sensor test. Does the sensor function correctly? Go to Step 6. Go to Step 2. 2 Check the harness connection. Is P/J1007 connected to the Punch Control Board? Are P/J2010 and P/J2011 connected to the Emitter and Receiver boards? Go to Step 3. Connect the harness. 3 Check the harness continuity. Is the harness conductive? Go to Step 4. Replace the harness. 4 Check the Side Registration Sensor Emitter Board. Are the LEDs illuminated? Go to Step 5. Replace the Emitter Board. 5 Check for +5 V to the sensor. Disconnect P/J1007. Is there +5 V at J1007-9 <=> ground? Replace the Receiver Board. Replace the Punch Control Board. 6 Replace the Finisher Control Board. Does the error still occur? Replace the Engine Control Board. Complete.

• Code: F134
• Description: Finisher Punch Motor Failure An error was detected in the Punch Motor.
• Causes: • Punch Motor • Punch Control Board • Inverter Power Supply
• Remedy: 1 Test the Punch Motor. 1. Close the Interlock Switches for test. 2. Run the Service Diagnostics Punch Motor test. Does the motor operate? Complete. Go to Step 2. 2 Check for +24 V to the Punch Motor. Disconnect P/J2002. Is the +24 V across J2002-1 <=> ground? Replace the Punch Motor. Go to Step 3. 3 Check Punch Control Board for 24 V. 1. Disconnect P/J1002 on the Punch Control Board. Is the +24 V across P1002 pins 1 and 2? Replace the Punch Motor Harness. Replace the Punch Control Board. If the error persists, go to Step 4. 4 Check all pins of the Inverter Interface Cable for continuity. Disconnect CN1 and CN2 from the Finisher Control Board and the opposite end from the Inverter. Is the cable conductive? Replace the Inverter Power Supply. If the error persists, replace the Finisher Control Board. Replace the cable.