Description: Tray 4 Out Of Place RAP The Tray 4 Paper Size Switch detected no tray.
Remedy: [For 2TM] Remove Trays 3 and 4. Replace Tray 3 with Tray 4. [024-949] occurs. Y↓N→Replace the faulty part of the Tray 4 Actuator. Check the installation of the Tray 4 Paper Size Switch. The Tray 4 Paper Size Switch is installed correctly. Y↓N→Install the Tray 4 Paper Size Switch correctly. Go to the BSD 7.4 Tray 4 Paper Size Sensing and check the connectors. [For TTM] Check the Tray 4 Actuator. The Tray 4 Actuator is not distorted. Y↓N→Replace the faulty part of the Tray 4 Actuator. Check the installation of the Tray 4 Paper Size Switch. The Tray 4 Paper Size Switch is installed correctly. Y↓N→Install the Tray 4 Paper Size Switch correctly. Go to the BSD 7.6 Tray 4 Paper Size Sensing and check the connectors.
Description: Tray 1 Empty RAP Tray 1 has run out of paper.
Remedy: Check the installation of the Tray 1 No Paper Sensor (PL 2.3) and the operation of the actuator. The Tray 1 Level Sensor is installed correctly and the actuator works. Y↓N→Reinstall the Tray 1 Level Sensor. Execute Component Control[071-201 Tray 1 No Paper Sensor]. Manually activate the Tray 1 No Paper Sensor (PL 2.3). The display changes. Y↓N→Check the connections of P/J101, P/J601 and P/J409. P/J101, P/J601 and P/J409 are connected correctly. Y↓N→Connect P/J101, P/J601 and P/J409. Check the wire between J101 and J409 for an open circuit or a short circuit. The wire between J101 and J409 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Measure the voltage between the MCU PWB P409A-10 (+) and GND (-). The voltage is approx. +5VDC. Y↓N→Replace the MCU PWB (PL 9.1). Measure the voltage between the MCU PWB P409B-12 (+) and GND (-). Activate the actuator of the Tray 1 No Paper Sensor (PL 2.3). The voltage changes. Y↓N→Replace the Tray 1 No Paper Sensor (PL 2.3). Replace the MCU PWB (PL 9.1). Replace the MCU PWB (PL 9.1).
Description: Tray 2 Empty RAP Tray 2 has run out of paper.
Remedy: Check the installation of the Tray 2 No Paper Sensor (PL 2.3) and the operation of the actuator. The Tray 2 Level Sensor is installed correctly and the actuator works. Y↓N→Reinstall the Tray 2 Level Sensor. Execute Component Control [071-202 Tray 2 No Paper Sensor]. Manually activate the Tray 2 No Paper Sensor (PL 12.3). The display changes. Y↓N→Check the connections of P/J103, P/J602 and P/J409. P/J103, P/J602 and P/J409 are connected correctly. Y↓N→Connect P/J103, P/J602 and P/J409. Check the wire between J103 and J409 for an open circuit or a short circuit. The wire between J103 and J409 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Measure the voltage between the MCU PWB P409B-10 (+) and GND (-). The voltage is approx. +5VDC. Y↓N→Replace the MCU PWB (PL 9.1). Measure the voltage between the MCU PWB P409B-12 (+) and GND (-). Activate the actuator of the Tray 2 No Paper Sensor (PL 2.3). The voltage changes. Y↓N→Replace the Tray 2 No Paper Sensor (PL 2.3). Replace the MCU PWB (PL 9.1). Replace the MCU PWB (PL 9.1).
Description: Tray 3 Empty RAP Tray 3 has run out of paper.
Remedy: Check the installation of the Tray 3 No Paper Sensor (PL 12.3/PL 13.6) and the operation of the actuator. The Tray 3 Level Sensor is installed correctly and the actuator works. Y↓N→Reinstall the Tray 3 Level Sensor. Execute Component Control[071-203 Tray 3 No Paper Sensor]. Manually activate the Tray 3 No Paper Sensor (PL 12.3/PL 13.6). The display changes. Y↓N→Check the connections of P/J102B, P/J661B and P/J549. P/J102B, P/J661B and P/ J549 are connected correctly. Y↓N→Connect P/J102B, P/J661B and P/J549. Check the wire between J102B and J549 for an open circuit or a short circuit. The wire between J102B and J549 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Measure the voltage between the Tray Module PWB P549-B10 (+) and GND (-). The voltage is approx. +5VDC. Y↓N→Replace the Tray Module PWB (PL 12.6/PL 13.8). Measure the voltage between the Tray Module PWB P549-B12 (+) and GND (-). Activate the actuator of the Tray 3 No Paper Sensor (PL 12.3/PL 13.6). The voltage changes. Y↓N→Replace the Tray 3 No Paper Sensor (PL 12.3/PL 13.6). Replace the Tray Module PWB (PL 12.6/PL 13.8). Replace the Tray Module PWB (PL 12.6/PL 13.8).
Description: Tray 4 Empty RAP Tray 4 has run out of paper
Remedy: Check the installation of the Tray 4 No Paper Sensor (PL 12.3/PL 13.6) and the operation of the actuator. The Tray 4 Level Sensor is installed correctly and the actuator works. Y↓N→Reinstall the Tray 4 Level Sensor. Execute Component Control[071-204 Tray 4 No Paper Sensor]. Manually activate the Tray 4 No Paper Sensor (PL 12.3/PL 13.6). The display changes. Y↓N→Check the connections of P/J102A, P/J661A and P/J549. P/J102A, P/J661A and P/ J549 are connected correctly. Y↓N→Connect P/J102A, P/J661A and P/J549. Check the wire between J102A and J549 for an open circuit or a short circuit. The wire between J102A and J549 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Measure the voltage between the Tray Module PWB P549-A10 (+) and GND (-). The voltage is approx. +5VDC. Y↓N→Replace the Tray Module PWB (PL 12.6/PL 13.8). Measure the voltage between the Tray Module PWB P549-A12 (+) and GND (-). Activate the actuator of the Tray 4 No Paper Sensor (PL 12.3/PL 13.6). The voltage changes. Y↓N→Replace the Tray 4 No Paper Sensor (PL 12.3/PL 13.6). Replace the Tray Module PWB (PL 12.6/PL 13.8). Replace the Tray Module PWB (PL 12.6/PL 13.8).
Description: MPT Empty RAP The MPT has run out of paper.
Remedy: Check the installation of the MPT No Paper Sensor (PL 7.1) and the operation of the actuator. The MPT No Paper Sensor is installed correctly and the actuator works. Y↓N→Reinstall the MPT No Paper Sensor. Execute Component Control[071-205 MPT No Paper Sensor]. Manually activate the MPT No Paper Sensor (PL 7.1). The display changes. Y↓N→Check the connections of P/J108, P/J605 and P/J411. P/J108, P/J605 and P/J411 are connected correctly. Y↓N→Connect P/J108, P/J605 and P/J411. Check the wire between J108 and J411 for an open circuit or a short circuit. The wire between J108 and J411 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Measure the voltage between the MCU PWB P411-6 (+) and GND (-). The voltage is approximately. +5VDC. Y↓N→Replace the MCU PWB (PL 9.1). Measure the voltage between the MCU PWB P411-8 (+) and GND (-). Activate the actuator of the MPT No Paper Sensor (PL 7.1). The voltage changes. Y↓N→Replace the MPT No Paper Sensor (PL 7.1). Replace the MCU PWB (PL 9.1). Replace the MCU PWB (PL 9.1).
Description: MPT Size Failure RAP The MPT is unable to detect the paper size.
Remedy: Check the installation and operation of the MPT Guide. The MPT Guide is installed correctly and the actuator works. Y↓N→Reinstall the MPT Guide. Measure the voltage between the MCU PWB P411-3 (+) and GND (-). Manually operate the MPT Guide. As the MPT Guide moves, the voltage changes accordingly. Y↓N→Check the connections of P/J107, P/J609, P/J605 and P/J411. P/J107, P/J609, P/ J605 and P/J411 are connected correctly. Y↓N→Connect P/J107, P/J609, P/J605 and P/J411. Check the wire between J107 and J411 for an open circuit or a short circuit. The wire between J107 and J411 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Measure the voltage between the MCU PWB P411-1 (+) and GND (-). The voltage is approx. +5VDC. Y↓N→Replace the MCU PWB (PL 9.1). Replace the MPT Paper Size Sensor (PL 7.3). Replace the MCU PWB (PL 9.1).
Nhận ưu đãi sớm nhất khi chương trình diễn ra
Đăng ký nhận bản tin
Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này.
Chính sách cookie
Những cookie này là cần thiết để trang web hoạt động đúng cách.
Những cookie này giúp chúng tôi hiểu cách khách truy cập tương tác với trang web.
Những cookie này được sử dụng để cung cấp quảng cáo cá nhân hóa.