Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Xerox WorkCentre 5325 — Trang 13/33

Code: 012-935

Description: (Integrated Finisher) Paper Remains at Entrance Sensor RAP • At Power On the Finisher Entrance Sensor detected paper. • While the Main Motor was operating at initialization at Power On, the Finisher Entrance Sensor detected paper. • When the Cycle down operation at the end of a job was complete, the Finisher Entrance Sensor was On.
Remedy: Check for paper remaining on the Finisher Entrance Sensor and how it is installed. The sensor is properly installed and free from paper. Y↓N→Remove the remaining paper and reinstall the sensor properly. Enter Component Control [012-140]. Move the Finisher Entrance Sensor actuator by hand or with a piece of paper. The display changes. Y↓N→Check the connections of P/J8709 and P/J8729. P/J8709 and P/J8729 are securely connected. Y↓N→Connect P/J8709 and P/J8729 securely. Check for an open or short circuit between P/J8709 and P/J8729. The wire between P/J8709 and P/J8729 are OK. Y↓N→Repair the open or short circuit. Measure the voltage between P/J8709-6 (+) on the Finisher PWB and GND (-). The voltage is approx. +5VDC. Y↓N→Go to Integrated Finisher Wirenets and check the +5VDC circuit. Measure the voltage between P/J8709-5 (+) on the Finisher PWB and GND (-). Actuate the Finisher Entrance Sensor. The voltage changes. Y↓N→Replace the Finisher Entrance Sensor (PL 22.5). Check the wires and connectors for an intermittent open or short circuit. If the problem continues, replace the Finisher PWB (PL 22.7). Check the wires and connectors for an intermittent open or short circuit. If the problem continues, replace the Finisher PWB (PL 22.7).

Code: 012-935

Description: Paper at Finisher Entrance Sensor RAP (LX) Control logic reports paper at the Finisher Entrance Sensor.
Remedy: Enter Component Control [012-100], Finisher Entrance Sensor. Select Start. Actuate the Finisher Entrance Sensor. The display changes. Y↓N→Check the wire between J8868 pin 2 and P/J8988 pin 2 for an open or short circuit, or a loose or damaged connector. The wire is OK. Y↓N→Repair/reconnect as required. Measure the voltage between P/J8988 pins 3 and 1 on the Finisher PWB (BSD 12.16 - Office Finisher LX Transportation). The voltage is approx. +5VDC. Y↓N→Replace the Finisher PWB (PL 23.16). Measure the voltage between P/J8988 pin 2 on the Finisher PWB and GND (BSD 12.16 - Office Finisher LX Transportation). Actuate the Finisher Entrance Sensor. The voltage changes. Y↓N→Replace the Finisher Entrance Sensor (PL 23.14). Replace the Finisher PWB (PL 23.16). Replace the Finisher PWB (PL 23.16).

Code: 012-949

Description: Punch Box Missing RAP (LX) Punch Box Set Sensor detected Punch Box to be missing.
Remedy: Enter Component Control [012-275], Punch Box Set Sensor (PL 23.5). Select Start. Remove and insert the Punch Box manually. The display changes Y↓N→Select Stop. Check continuity between the Punch Box Set Sensor ( J8866); P8863; and the Finisher PWB ( J8897). The continuity check is OK. Y↓N→Repair the open circuit or short circuit. Replace the Punch Box Set Sensor (PL 23.5). If the problem continues, replace the Finisher PWB (PL 23.16). Check the Punch Box Set Sensor Actuator and Punch Box Guide for deformation. The Punch Box can be removed and inserted properly. Y↓N→Repair or replace the Punch Box (PL 23.2). Select Stop. If the problem continues, replace the Finisher PWB (PL 23.16).

Code: 012-966

Description: Scratch Sheet Compile RAP Paper was detected that was either out of spec, in poor condition (wrinkled, curled) and was ejected to the compiler.
Remedy: Check the specifications of paper. The paper is in spec. Y↓N→Replace the paper with new paper that is in spec. Check the condition of the paper. The paper is in normal condition without any problem that causes the paper to be bent (dog eared) or jam. Y↓N→Resolve any problem that causes the paper to be bent or caught. Check for a Fault Code. Another Fault Code is displayed. Y↓N→If the problem continues, replace the Finisher PWB (PL 23.16). Go to the appropriate Fault Code.

Code: 013-210

Description: Booklet Staple Move Home Sensor ON RAP (LX) Booklet Staple Move Home Sensor does not turn on within designated time period
Remedy: Execute Component Control [013-143], Booklet Staple Move Home Sensor. Move the Booklet Staplers to block and unblock the sensor (PL 23.18). The display changes. Y↓N→Check the wire between J8897 pin 2 and P/J8991 pin 2 for an open or short circuit, or a loose or damaged connector. The wire is OK. Y↓N→Repair/reconnect as required. Measure the voltage between P/J8991, pins 3 and 1 on the Booklet PWB. The voltage is approx. +5VDC. Y↓N→Replace the Booklet PWB (PL 23.21). Measure the voltage between P/J8991 pin 2 on the Booklet PWB and GND. Actuate the Booklet Staple Move Home Sensor. The voltage changes. Y↓N→Replace the Booklet Staple Move Home Sensor (PL 23.18). Replace the Booklet PWB (PL 23.21). Alternately execute Component Control [013-028], Stapler Move Motor In and [013-029], Stapler Move Motor Out. The Stapler Move Motor moves. Y↓N→Check the wires between P/J8992 pins 1~6 on the Booklet PWB and P/J8906 on the Booklet Stapler Move Motor for an open or short circuit, or loose or damaged connectors. The wires are OK. Y↓N→Repair/replace as required. Monitor the voltage at J8984, pin 3. Alternately execute Component Control [013-028], Stapler Move Motor In and [013-029], Stapler Move Motor Out. An AC clock pulse is detected. Y↓N→Check the wire between J8984, pin 3 and J8985 pin 4. If the wire is OK, replace the Finisher PWB (PL 23.16). Replace the Booklet Stapler Move Motor (PL 23.18). If the problem persists, replace the Booklet PWB (PL 23.21). Go to BSD 12.25 - Office Finisher Booklet Staple Positioning5 and check for an intermittent circuit.

Code: 013-211

Description: Booklet Staple Move Home Sensor OFF RAP (LX) Booklet Staple Move Home Sensor does not turn off within designated time period
Remedy: Execute Component Control [013-143], Booklet Staple Move Home Sensor. Move the Booklet Staplers to block and unblock the sensor (PL 23.18). The display changes. Y↓N→Check the wire between J8897 pin 2 and P/J8991 pin 2 for an open or short circuit, or a loose or damaged connector. The wire is OK. Y↓N→Repair/reconnect as required. Measure the voltage between P/J8991, pins 3 and 1 on the Booklet PWB. The voltage is approx. +5VDC. Y↓N→Replace the Booklet PWB (PL 23.21). Measure the voltage between P/J8991 pin 2 on the Booklet PWB and GND. Actuate the Booklet Staple Move Home Sensor. The voltage changes. Y↓N→Replace the Booklet Staple Move Home Sensor (PL 23.18). Replace the Booklet PWB (PL 23.21). Alternately execute Component Control [013-028], Stapler Move Motor In and [013-029], Stapler Move Motor Out. The Stapler Move Motor moves. Y↓N→Check the wires between P/J8992 pins 1~6 on the Booklet PWB and P/J8906 on the Booklet Stapler Move Motor for an open or short circuit, or loose or damaged connectors. The wires are OK. Y↓N→Repair/replace as required. Monitor the voltage at J8984, pin 3. Alternately execute Component Control [013-028], Stapler Move Motor In and [013-029], Stapler Move Motor Out. An AC clock pulse is detected. Y↓N→Check the wire between J8984, pin 3 and J8985 pin 4. If the wire is OK, replace the Finisher PWB (PL 23.16). Replace the Booklet Stapler Move Motor (PL 23.18). If the problem persists, replace the Booklet PWB (PL 23.21). Go to BSD 12.25 - Office Finisher Booklet Staple Positioning and check for an intermittent circuit.

Code: 013-212

Description: Booklet Staple Move Position Sensor On Fail RAP (LX) Booklet Staple Move Position Sensor does not turn on within designated time period
Remedy: Execute Component Control [013-144], Booklet Staple Move Position Sensor. Move the Booklet Stapler to block and unblock the sensor (PL 23.18). The display changes. Y↓N→Check the wire between J8898 pin 2 and P/J8991 pin 5; and the wire between J8984, pin 5 and J8985 pin 5 for an open or short circuit, or a loose or damaged connector. The wires are OK. Y↓N→Repair/reconnect as required. Measure the voltage between P/J8991, pins 6 and 4 on the Booklet PWB. The voltage is approx. +5VDC. Y↓N→Replace the Booklet PWB (PL 23.21). Measure the voltage between P/J8991 pin 5 on the Booklet PWB and GND. Actuate the Booklet Staple Move Position Sensor. The voltage changes. Y↓N→Replace the Booklet Staple Move Position Sensor (PL 23.18). Measure the voltage between J8895 pin 5 on the Finisher PWB and GND. Actuate the Booklet Staple Move Position Sensor. The voltage changes. Y↓N→Replace the Booklet PWB (PL 23.21). If the problem persists, replace the Finisher PWB (PL 23.16). Replace the Finisher PWB (PL 23.16). Alternately execute Component Control [013-028], Stapler Move Motor In and [013-029], Stapler Move Motor Out. The Stapler Move Motor moves. Y↓N→Check the wires between P/J8992 pins 1~6 on the Booklet PWB and P/J8906 on the Booklet Stapler Move Motor for an open or short circuit, or loose or damaged connectors. The wires are OK. Y↓N→Repair/replace as required. Monitor the voltage at J8984, pin 3. Alternately execute Component Control [013-028], Stapler Move Motor In and [013-029], Stapler Move Motor Out. An AC clock pulse is detected. Y↓N→Check the wire between J8984, pin 3 and J8985 pin 4. If the wire is OK, replace the Finisher PWB (PL 23.16). Replace the Booklet Stapler Move Motor (PL 23.18). If the problem persists, replace the Booklet PWB (PL 23.21). Go to BSD 12.25 - Office Finisher Booklet Staple Positioning and check for an intermittent circuit.

Code: 013-213

Description: Booklet Staple Move Position Sensor Off Fail RAP (LX)
Remedy: Execute Component Control [013-144], Booklet Staple Move Position Sensor. Move the Booklet Stapler to block and unblock the sensor (PL 23.18). The display changes. Y↓N→Check the wire between J8898 pin 2 and P/J8991 pin 5; and the wire between J8984, pin 5 and J8895 pin 5 for an open or short circuit, or a loose or damaged connector. The wires are OK. Y↓N→Repair/reconnect as required. Measure the voltage between P/J8991, pins 6 and 4 on the Booklet PWB. The voltage is approx. +5VDC. Y↓N→Replace the Booklet PWB (PL 23.21). Measure the voltage between P/J8991 pin 5 on the Booklet PWB and GND. Actuate the Booklet Staple Move Position Sensor. The voltage changes. Y↓N→Replace the Booklet Staple Move Position Sensor (PL 23.18). Measure the voltage between J8895 pin 5 on the Finisher PWB and GND. Actuate the Booklet Staple Move Position Sensor. The voltage changes. Y↓N→Replace the Booklet PWB (PL 23.21). If the problem persists, replace the Finisher PWB (PL 23.16). Replace the Finisher PWB (PL 23.16). Alternately execute Component Control [013-028], Stapler Move Motor In and [013-029], Stapler Move Motor Out. The Stapler Move Motor moves. Y↓N→Check the wires between P/J8992 pins 1~6 on the Booklet PWB and P/J8906 on the Booklet Stapler Move Motor for an open or short circuit, or loose or damaged connectors. The wires are OK. Y↓N→Repair/replace as required. Monitor the voltage at J8984, pin 3. Alternately execute Component Control [013-028], Stapler Move Motor In and [013-029], Stapler Move Motor Out. An AC clock pulse is detected. Y↓N→Check the wire between J8984, pin 3 and J8895 pin 4. If the wire is OK, replace the Finisher PWB (PL 23.16). Replace the Booklet Stapler Move Motor (PL 23.18). If the problem persists, replace the Booklet PWB (PL 23.21). Go to BSD 12.25 - Office Finisher Booklet Staple Positioning and check for an intermittent circuit.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie