• Code: 1150
• Description: Home Position Sensor Error
  The Carriage cannot be moved to it’s home position.
• Remedy: • Enter the Sensors Menu (in Maintenance Mode) and select "Printer Sensors". Then execute the "Home Position" option, which will display the state of the home position sensor. If the home position is detected, "1" will be displayed on the Front Panel. If the home position is not detected, manually move the Carriage and check the Front Panel to see if the "1" is displayed. • Make sure the Home Position Sensor Cable is connected correctly and is not damaged. • Replace the Home Position Sensor. • Replace the Main PCA

• Code: 1160
• Description: Wiping Error
  When the Wiping Motor has been running for a while, the sensor fails to detect that the Motor has made one turn.
• Remedy: • If the Wiper does not turn once: – Check manually by turning the Wiper Gears to see if the Wiper turns. If it does not turn then replace the Wiping Station. – Check whether 24 V is supplied to the Main PCA with the circuit tester. If the Wiper Motor does not turn even though the 24 V is supplied, there is a possibility of a failure in the Wiper Motor. Replace the Wiping Station . Page 8-145. – Make sure the Wiper Sensor Cable is connected correctly and is not damaged. – If the error continues, replace the Main PCA • If the Wiper does turn once: – Check whether the Wiper Sensor can be switched ON and OFF by manually rotating the Wiper. Check whether the lever type switch is not loose. – Make sure the Wiper Sensor Cable is connected correctly and is not damaged. – Make sure that the Wiper Sensor is clean. – If the error continues, replace the Main PCA

• Code: 1170
• Description: Temperature Sensor Error
  The Temperature Sensor detects abnormal temperatures (-10C or lower or 85C or higher).
• Remedy: • Make sure that the Printer is in an environment where the temperature is between -10oC and 85oC. • Make sure the Ambient Temperature Sensor Cable is connected correctly and is not damaged. • Replace the Main PCA

• Code: 1180
• Description: Capping Motor Error
  Capping Motor over current is detected.
• Remedy: • When the ambient temperature is very low, the Pump Motor Tube becomes hard and the load on the Capping Motor is increased. Make sure that the Printer is in an environment where the temperature is not below -10oC or higher than +85oC. • The Capping Station has a Torque Limiter for up and down operation so that the Capping Station does not experience any over current. • Apply grease on the shaft of the Capping Station Gear so that it helps with rotation. • Enter the Motors Menu (in Maintenance Mode) and open Solenoids L and R. Access the Pump Motors and check whether the Motor Drive Circuit and Motor work correctly by manually rotating the Motor. When the home position is set to "0", it is clear that the home position has not been adjusted and that capping is not available. • Make sure that the Capping Station cables are connected correctly and are not damaged • If the Capping Motor cannot be rotated, replace the Capping Station . Page 8-120. • Make sure the Cap Sensor Cable is connected correctly and is not damaged. • Replace the Main PCA

• Code: 119x
• Description: Head Relay Variable Supply Error
  Output voltages of the Head Relay Board are abnormal.
• Remedy: • Check whether 36V is supplied to the Main PCA. If not, then: – Make sure that the Rear Cover is closed. – Replace Power Supply Unit • Preset the Head Relay Board Voltage from the Diagnostic Menu. Use a circuit tester to check the voltages of the channels that have an error. • If the voltage is supplied, it means that the voltage check circuit is defective. Replace the Main PCA • If the voltage is not supplied, replace the Head Relay Board • There is a possibility of a short circuit off the Head Relay Board output line. Perform a short circuit test on the Main PCA. • Make sure the Carriage Trailing Cable is connected correctly and is not damaged.

• Code: 11Ax
• Description: NVRAM Error
  The data in the NVRAM is incorrect.
• Remedy: • Switch the Printer OFF and ON again and check if the error still appears. • If the error continues, skip the Power-ON Self-Diagnostic by keeping the Cancel Key pressed and powering ON the Printer. Perform NVRAM Initialization (. Page 4-47) and then perform Restore Calibs (. Page 4-48). Switch the Printer OFF and ON again and check if the error still appears. • If the error continues, restore the Printer to defaults settings. Switch the Printer OFF and ON again and check if the error still appears. • Check whether the NVRAM is mounted on the Main PCA correctly. If necessary, replace the NVRAM • If the error continues, replace the Main PCA

• Code: 11C0
• Description: Cap Position Error
  The Carriage position sensors have detected more than a 2mm gap during the capping operation.
• Remedy: • Make sure that the Encoder Strip is not stained. • Make sure that the Encoder Sensor is mounted correctly and that the cable is connected correctly. • Make sure that the Trailing Cable is connected correctly. • Replace the Carriage PCA • If the error continues, replace the Main PCA

• Code: 11D0
• Description: Cooling Fan Error
  When the Printhead temperature reaches above 43C, the Printer will check whether the temperature drops below 43C during printing. This error will appear if the temperature does not drop below 43C after 10 minutes.
• Remedy: • Make sure that the Printhead Cooling Fans are working correctly. If the Printhead Cooling Fans are not working correctly, replace them • Make sure that the Printer Cooling Fans are connected and working correctly.