Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi HP Latex 3000 — Trang 21/42

Code: 16.01.01:41 ... 16.01.06:41

Description: Curing module 0X overcurrent warning. contact your support representative to check input voltage configuration.
Causes: a. Wrong configuration of AC input tension b. AC input tension out of range c. Resistor degradation
Remedy: 1. Check AC input tension and reconfigure the printer’s AC input configuration. 2. Check resistor and replace if necessary.

Code: 16.02.01:01, 16.02.02:01

Description: Curing module X PCA error. Module disabled, substrate going under this module won't be cured. But if module is required to print, reinstall/upgrade printer firmware. If problem persists, call support.
Causes: a. Curing PCA internal error b. Curing PCA malfunction
Remedy: 1. Reinstall or update the printer’s firmware. 2. Replace the curing PCA.

Code: 16.02.01:04, 16.02.02:04

Description: Curing module X comm error between curing PCA and e-box. Module disabled, substrate going under this module won't be cured. But, if module is required to print, run subsystem diagnostic. If problem persists, call support.
Causes: a. Curing PCA connection problem b. Curing PCA malfunction
Remedy: 1. Check connections. 2. Replace the curing PCA.

Code: 16.02.01:10, 16.02.02:10

Description: Curing module X PCA DC supply error. Module disabled, substrate going under this module won't be cured. But, if module is required to print, run subsystem diagnostic. If problem persists, call support.
Causes: a. DC power error b. Curing PCA problem c. Cabling problem d. Curing PCA power supply error
Remedy: Replace any faulty part.

Code: 16.02.01:21, 16.02.02:21

Description: Curing module X PCA temp too high. Module disabled, substrate going under this module won't be cured. But, if module is required to print, run subsystem diagnostic. If problem persists, call support.
Causes: a. Ambient temperature too high b. Not enough airflow in module c. Failure in temperature control
Remedy: 1. Check the ambient temperature. 2. Check that the fans are working, and that the holes in the curing plate are not blocked. 3. Check the curing PCA.

Code: 16.03.00:03

Description: Curing bottom plate model not set or wrongly set in firmware. Contact your support representative.
Causes: Curing bottom plate model or revision is not properly set in the printer.
Remedy: Go to the diagnostic utilities in Print Care and run the set curing bottom plate diagnostic in order to set the right model and revision.

Code: 16.10.01:20 ... 16.10.06:20

Description: Curing module X temperature channel 1 out of range (recirculation). Module disabled, substrate going under this module won't be cured. But, if module is required to print, run subsystem diagnostic. If problem persists, call support.
Causes: a. Ambient temperature too high b. Not enough airflow in module c. Failure in temperature control
Remedy: 1. Check the ambient temperature. 2. Check that the fans are working, and that the holes in the curing plate are not blocked. 3. Check the curing PCA.

Code: 16.11.01:01 ... 16.11.06:01

Description: Curing module X chamber 1 Temperature sensor failure Module disabled, substrate going under this module won't be cured. But if module is required to print, run subsystem diagnostic. If the problem persists, call support.
Causes: Temperature sensor problem
Remedy: Replace the temperature sensor.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie