• Code: 16.13.01:01 ... 16.13.06:01
• Description: Curing module X chamber 1 fan no spinning detected. Module disabled, substrate going under this module won't be cured. But if module is required to print, run subsystem diagnostic. If the problem persists, call support.
• Causes: The fan is not detected to be spinning. The problem could be the fan itself, the fan power, or the tachometer signal.
• Remedy: 1. Check the fan connections. 2. Replace the fan.

• Code: 16.14.01:15 ... 16.14.06:15
• Description: Curing module X chamber 1 open circuit detected. Module disabled, substrate going under this module won't be cured. But, if module is required to print, run subsystem diagnostic. If problem persists, call support.
• Causes: a. Curing PCA fuse blown b. Resistor failure c. Resistor cabling error d. Curing PCA failure (relay, triac, current sensor) e. Curing PCA firmware bug
• Remedy: 1. Reinstall or update the firmware. 2. Check the curing PCA and replace it if necessary. See Curing and vapor removal PCA. 3. Check the resistor and replace it if necessary.

• Code: 16.15.01:01 ... 16.15.06:01
• Description: Curing module X resistor 1 failure. Module disabled, substrate going under this module won't be cured. But, if module is required to print, run subsystem diagnostic. If problem persists, call support.
• Causes: a. Curing PCA firmware bug b. Curing PCA failure (relay or triac)
• Remedy: 1. Reinstall or update the firmware. 2. Check the curing PCA and replace it if necessary.

• Code: 16.20.01:20 ... 16.20.06:20
• Description: Curing module X temperature channel 2 out of range (recirculation). Module disabled, substrate going under this module won't be cured. But, if module is required to print, run subsystem diagnostic. If problem persists, call support.
• Causes: a. Ambient temperature too high b. Not enough airflow in module c. Failure in temperature control
• Remedy: 1. Check the ambient temperature. 2. Check that the fans are working, and that the holes in the curing plate are not blocked. 3. Check the curing PCA.

• Code: 16.21.01:01 ... 16.21.06:01
• Description: Curing module X chamber 2 temperature sensor failure. Module disabled, substrate going under this module won't be cured. But, if module is required to print, run subsystem diagnostic. If problem persists, call support.
• Causes: a. Ambient temperature too high b. Not enough airflow in module c. Failure in temperature control
• Remedy: Replace temperature sensor.

• Code: 16.23.01:01 ... 16.23.06:01
• Description: Curing module X chamber 2 fan no spinning detected. Module disabled, substrate going under this module won't be cured. But, if module is required to print, run subsystem diagnostic. If problem persists, call support.
• Causes: The fan is not detected to be spinning. The problem could be the fan itself, the fan power, or the tachometer signal.
• Remedy: 1. Check the fan connections. 2. Replace the fan.

• Code: 16.24.01:15 ... 16.24.06:15
• Description: Curing module X chamber 2 open circuit detected. Module disabled, substrate going under this module won't be cured. But, if module is required to print, run subsystem diagnostic. If problem persists, call support.
• Causes: a. Curing PCA fuse blown b. Resistor failure c. Resistor cabling error d. Curing PCA failure (relay, triac, current sensor) e. Curing PCA firmware bug
• Remedy: 1. Reinstall or update the firmware. 2. Check the curing PCA and replace it if necessary. See Curing and vapor removal PCA. 3. Check the resistor and replace it if necessary.

• Code: 16.25.01:01 ... 16.25.06:01
• Description: Curing module X resistor 2 failure. Module disabled, substrate going under this module won't be cured. But, if module is required to print, run subsystem diagnostic. If problem persists, call support.
• Causes: a. Curing PCA firmware bug b. Curing PCA failure (relay or triac)
• Remedy: 1. Reinstall or update the firmware. 2. Check the curing PCA and replace it if necessary.