Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi HP Latex 3000 — Trang 8/42

Code: 10.03.04:18

Description: E-cabinet PSU-4 voltage too high. The PSU-4 voltage is too high.
Causes: a. PSU-4 voltage too high b. PCA malfunction
Remedy: 1. Reboot the printer. 2. Run the subsystem diagnostic. 3. If the problem persists: a. Disconnect the DC output cable from the PCA. b. Measure the PSU-4 output voltage with a voltage meter. c. If lower than 13 V +10%, it is likely a PCA malfunction. d. Otherwise adjust the PSU-1 output voltage through its adjustment potentiometer with the help of a voltage meter. Voltage must be within 13 V ±5%. e. If the PSU-4 cannot be adjusted, replace the PSU. See E-cabinet PSUs 1 to 4.

Code: 10.03.04:19

Description: E-cabinet PSU-4 voltage too low. The PSU-4 voltage is too low.
Causes: a. PSU-4 voltage too low b. PCA malfunction
Remedy: 1. Reboot the printer. 2. Run the subsystem diagnostic. 3. If the problem persists: a. Disconnect the DC output cable from the PCA. b. Measure the PSU-4 output voltage with a voltage meter. c. If higher than 13V +10%, it is likely a PCA malfunction. d. Otherwise adjust the PSU-4 output voltage through its adjustment potentiometer with the help of a voltage meter. Voltage must be within 13V +/- 5%. e. If the PSU-4 cannot be adjusted, replace the PSU. See E-cabinet PSUs 1 to 4.

Code: 10.03.05:01

Description: E-cabinet PSU-5 no voltage or alarm signal asserted. The PSU-5 is not supplying voltage, or an alarm signal is activated.
Causes: a. PSU-5 not receiving AC voltage b. PSU-5 DC output cable disconnected c. PSU-5 in fault mode (overcurrent, overvoltage, overtemperature) d. PSU-5 end of life e. PCA malfunction
Remedy: 1. Check ACB-6. 2. Run subsystem diagnostic. 3. Reboot the printer. 4. Check that the PSU-5 feedback LED is lit. 5. If the LED is lit, check the DC output cable and the PCA. 6. If the PSU-5 is still not working, replace the PSU-5. See E-cabinet PSUs 5 to 7. 7. If the problem persists, call support.

Code: 10.03.05:10

Description: PSU-5 ground to earth voltage out of range. Run subsystem diagnostic. If the problem persists, call support.
Causes: The subsystem powered by this PSU may be not properly earthed. NOTE: In the case of this PSU, this error may appear as scan-axis motor braking, but it doesn't mean that the scan-axis motor is faulty.
Remedy: Check powered subsystem earthing.

Code: 10.03.05:18

Description: E-cabinet PSU-5 voltage too high. The PSU-5 voltage is too high.
Causes: a. PSU-5 voltage too high b. PCA malfunction
Remedy: 1. Reboot the printer. 2. Run the subsystem diagnostic. 3. If the problem persists: a. Disconnect the DC output cable from the PCA. b. Measure the PSU-5 output voltage with a voltage meter. c. If lower than 42V +10%, it is likely a PCA malfunction. d. Otherwise adjust the PSU-5 output voltage through its adjustment potentiometer with the help of a voltage meter. Voltage must be within 42V +/- 5%. e. If the PSU-5 cannot be adjusted, replace the PSU. See E-cabinet PSUs 5 to 7.

Code: 10.03.05:19

Description: E-cabinet PSU-5 voltage too low. The PSU-5 voltage is too low.
Causes: a. PSU-5 voltage too low b. PCA malfunction
Remedy: 1. Reboot the printer. 2. Run the subsystem diagnostic. 3. If the problem persists: a. Disconnect the DC output cable from the PCA. b. Measure the PSU-5 output voltage with a voltage meter. c. If higher than 42V +10%, it is likely a PCA malfunction. d. Otherwise adjust the PSU-5 output voltage through its adjustment potentiometer with the help of a voltage meter. Voltage must be within 42V +/- 5%. e. If the PSU-5 cannot be adjusted, replace the PSU. See E-cabinet PSUs 5 to 7.

Code: 10.03.06:01

Description: E-cabinet PSU-6 no voltage or alarm signal asserted. The PSU-6 is not supplying voltage, or an alarm signal is activated.
Causes: a. PSU-6 not receiving AC voltage b. PSU-6 DC output cable disconnected c. PSU-6 in fault mode (overcurrent, overvoltage, overtemperature) d. PSU-6 end of life e. PCA malfunction
Remedy: 1. Check ACB-6. 2. Run subsystem diagnostic. 3. Reboot the printer. 4. Check that the PSU-6 feedback LED is lit. 5. If the LED is lit, check the DC output cable and the PCA. 6. If the PSU-6 is still not working replace the PSU-6. See E-cabinet PSUs 5 to 7. 7. If the problem persists, call support.

Code: 10.03.06:10

Description: PSU_6 ground to earth voltage out of range. Run subsystem diagnostic. If the problem persists, call support.
Causes: The subsystem powered by this PSU may be not properly earthed.
Remedy: Check powered subsystem earthing.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie