Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Xerox WorkCentre 6015 — Trang 8/10

Code: 091-402

Description: XERO Near Life The xerographics assembly is approaching end of life.
Causes: • MCU Board, PL7.2.2
Remedy: 1 Turn the printer off and then on. Does the error persist? Replace the MCU Board. Complete. 2 Does the error persist? Contact your designated field support for assistance. Complete.

Code: 092-310, 092-910

Description: Check Unit ADC Sensor This message indicates that the ADC Sensor needs cleaning. • 092-310: ADC Sensor Dustiness Pre Warning • 092-910: ADC Sensor Dustiness
Causes: • MCU Board, PL7.2.2
Remedy: 1 Disconnect P/J14 on the MCU Board. Is the voltage across ground at P/J14-1 and P/J14-9 on the MCU Board +5 VDC? Go to step 2. Replace the MCU Board, then go to step 2. 2 Does the error persist? Contact your designated field support for assistance. Complete.

Code: 092-651

Description: ADC Sensor Error An ADC Sensor error is detected.
Causes: • MCU Board, PL7.2.2
Remedy: 1 Clean the ADC sensor. Does the error persist when the power is turned on? Go to step 2. Complete. 2 Disconnect the harness at MCU Board P/J14 and at xerographics assembly P/J140, and check the harness for continuity. Is the harness continuous? Go to step 3. Repair the harness. 3 Replace the MCU Board. Does the error persist when the power is turned on? Contact your designated field support for assistance. Complete.

Code: 092-661

Description: ENV Sensor Error An error occurred while reading the Humidity Sensor.
Causes: • MCU Board, PL7.2.2
Remedy: 1 Replace the MCU Board. Does the error persist when the power is turned off and on? Contact your designated field support for assistance. Complete.

Code: 093-423 ... 093-426

Description: X CRU Near Life A Low Toner Cartridge (C, M, Y, or K) state was detected. • 093-423: Y CRU Near Life • 093-424: M CRU Near Life • 093-425: C CRU Near Life • 093-426: X CRU Near Life
Causes: • Harn assy dckr, PL4.1.2 • MCU Board, PL7.2.2
Remedy: 1 Reseat the Toner Cartridge. Does the error persist? Go to step 2. Complete. 2 Check P/J13 on the MCU Board. Is the connector secure? Go to step 4. Reconnect P/J13, then go to step 3. 3 Does the error persist? Go to step 4. Complete. 4 Replace the MCU Board. Does the error persist? Contact your designated field support for assistance. Complete.

Code: 093-919 ... 093-922

Description: X Toner Low Density. The printer detects low density of toner in the indicated Toner Cartridge. • 093-919: X Toner Low Density • 093-920: X Toner Low Density • 093-921: X Toner Low Density • 093-922: X Toner Low Density
Causes: • MCU Board, PL7.2.2
Remedy: 1 Clean the ADC sensor. Does the error persist? Go to step 2. Complete. 2 Check that MCU Board P/J14 is securely connected? Is the connection secure? Go to step 3. Reconnect P/J14, then go to step 3. 3 Does the error persist? Replace the MCU Board. Contact your designated field support for assistance.

Code: 093-926, 093-960, 093-961, 093-962

Description: CRUM ID Error, X CRU Detached An unsupported Toner Cartridge (C, M, Y, or K) is detected, or a No Toner Cartridge Installed state was detected. • 093-926: CRUM ID Error • 093-960: CRUM ID Error • 093-961: CRUM ID Error • 093-962: CRUM ID Error
Causes: • MCU Board, PL7.2.2 • Harness Assembly DCKR, PL4.1.2
Remedy: 1 Check that the Toner Cartridges installed in the printer are Xerox cartridges. Are the Toner Cartridges installed in the printer Xerox Toner Cartridges? Go to step 2. Complete. 2 Disconnect P/J13 on the MCU Board and unlace the harness. Inspect the harness for damage. Is the harness damaged? Repair the harness, then go to step 3. Go to step 3. 3 Does the error persist? Replace the MCU Board, then go to step 4. Complete. 4 Disconnect P/J13 on the PWBA MCU. Is the voltage across ground to P/J13-3 on the MCU Board approximately +3.3 VDC? Repair the Harness Assembly DCKR. Go to step 5. 5 Replace the Toner Cartridge (C, M, Y, or K). Does the error persist? Replace the MCU Board. Complete.

Code: 093-930 ... 093-933

Description: X CRU Life Over The indicated Toner Cartridge has reached end of life. • 093-930 to 093-933: X CRU Life Over
Causes: • Harn assy dckr, PL4.1.2 • MCU Board, PL7.2.2
Remedy: 1 Reseat the appropriate Toner Cartridge. Does the error persist? Go to step 2. Complete. 2 Does the error persist when the power is turned off and on? Go to step 3. Complete. 3 Check P/J13 on the MCU Board. Is the connection secure? Go to step 5. Reconnect P/J13, then go to step 4. 4 Does the error persist? Go to step 5. Complete. 5 Disconnect P/J13 on the MCU Board, and inspect the harness. Is the harness damaged? Repair the harness, then go to step 6. Go to step 7. 6 Does the error persist? Go to step 7. Complete. 7 Replace the Toner Cartridge (C, M, Y, or K). Does the error persist? Replace the MCU Board, then go to step 4. Contact your designated field support for assistance.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie