Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Xerox Phaser 4600 — Trang 5/16

Code: 04-810-00

Description: Rear Fan Failure
Causes: The Rear Door Fan has failed.
Remedy: • Close the Rear Door. • Check for obstructions blocking fan rotation.
Cycle system power. The error message is displayed. Y↓ N→Perform SCP 6 Final Actions. Select dC330 code 10-500 to test the Rear Fan. The Fan rotates. Y↓ N→Replace the Fan, then retest. The Fan rotates. Y↓ N→Check the Rear Door connection P/J63. The connector is undamaged. Y↓ N→Repair or replace the Rear Door. Remove the Right Cover and check CN4 on the Joint Board. The connection is secure. Y↓ N→Secure the connections. Replace these components in order until the error is corrected. 1. Rear Door, PL 28.25 Item 1 2. Joint Board, PL 9.15 Item 7 3. Exit Assembly, PL 10.30 Item 25 Reassemble and perform SCP 6 Final Actions. Reassemble and perform SCP 6 Final Actions.

Code: 04-930-00

Description: Main Fan Failure
Causes: The SMPS Fan has failed.
Remedy: • Check for obstructions blocking fan rotation.
Cycle system power. The error message is displayed. Y↓ N→Perform SCP 6 Final Actions. Select dC330 code 04-120 to test the SMPS Fan. The Fan rotates. Y↓ N→Replace the Fan, then retest. The Fan rotates. Y↓ N→Remove the Left Cover and check CN1 on the Joint Board. The connection is secure. Y↓ N→Secure the connections. Replace these components in order until the error is corrected. 1. SMPS Fan, PL 1.15 Item 6 2. Joint Board, PL 9.15 Item 7 Reassemble and perform SCP 6 Final Actions. Reassemble and perform SCP 6 Final Actions.

Code: 06-100-00, 06-200-00

Description: LSU Error
Causes: 06-100-00 The Laser Unit has failed. The Laser Unit did not reach ready within a defined time. 06-200-00 LSU Hsync Error. The Laser Unit has failed.
Remedy: • Cycle system power.
The error message is displayed. Y↓ N→Perform SCP 6 Final Actions. Select dC330 code 06-100 to test the Laser Unit. The Laser Unit is operational (on/off). Y↓ N→Replace the Laser Unit , then retest. The Laser Unit is operational. Y↓ N→Replace the IP Board . Reassemble and perform SCP 6 Final Actions. Reassemble and perform SCP 6 Final Actions.

Code: 07-110-00

Description: Paper Empty at Tray 2
Causes: The Tray 2 No Paper indicates the Tray is empty.
Remedy: 1. Add media to the Tray. 2. Check the No Paper Sensor Actuator. 3. Check for obstruction of the Pick mechanism.
Check the Tray 2 No Paper Sensor Actuator. The actuator is undamaged and motion is good. Y↓ N→Repair or replace the Tray 2 No Paper Sensor Actuator. Select dC330 code 07-210 to test the sensor. The sensor signal changes (high/low). Y↓ N→Replace the Tray 2 No Paper Sensor (PL 8.15 Item 19), then retest. The sensor signal changes. Y↓ N→Remove the Right Cover and reseat CN12 on the MCU Board, then retest. The sensor signal changes. Y↓ N→Replace the MCU Board. Reassemble and perform SCP 6 Final Actions. Reassemble and perform SCP 6 Final Actions. Reassemble and perform SCP 6 Final Actions.

Code: 07-120-00

Description: Tray 2 is Open
Causes: The Size Switch indicates the Tray is not fully installed.
Remedy: 1. Close the Tray. 2. Check the Size Switch.
Cycle system power. The error message is displayed. Y↓ N→Complete. Remove Tray 2 and inspect the Size Switch. The Size Switch is undamaged. Y↓ N→Replace the Size Switch, then retest. Select dC330 code 07-200 to test the switch. The switch signals change (open/closed). Y↓ N→Remove the Right Cover and reseat CN11 on the MCU Board, then retest. The sensor signal changes. Y↓ N→Replace the MCU Board. Replace these components in order until the error is corrected. 1. Size Switch, PL 3.10 Item 9 2. MCU Board, PL 3.10 Item 3

Code: 07-130-00

Description: Jam 0 in Tray 2
Causes: Media present at the Take Away Sensor.
Remedy: 1. Check media condition. 2. Check for obstructions in the media path.
Check the Nudger, Feed, and Separator Rollers for excessive wear or contamination. The rollers are undamaged and clean. Y↓ N→Clean or replace the rollers. Check for obstructions or debris in the media path. The media path is clear. Y↓ N→Clear the media path of obstructions or debris. Check Tray 2 pick assembly (PL 8.15) motion. Pick assembly motion is good. Y↓ N→Repair improper pick assembly motion. Select dC330 code 08-820 to test the Feed Clutch. The clutch is engaged (on/off). Y↓ N→Remove the Right Cover and reseat CN12 on the MCU Board, then retest. The clutch is engaged. Y↓ N→Replace the Feed Clutch. Reassemble and perform SCP 6 Final Actions. Select dC330 code 04-580 to test the Feed Drive Assembly. The Feed Drive Assembly rotates (on/off). Y↓ N→Remove the Right Cover and reseat CN12 on the MCU Board, then retest. The Feed Drive Assembly rotates. Y↓ N→Replace the Feed Drive Assembly. Reassemble and perform SCP 6 Final Actions. Replace the MCU Board.

Code: 07-210-00

Description: Paper Empty at Tray 3
Causes: The Tray 3 No Paper indicates the Tray is empty.
Remedy: 1. Add media to the Tray. 2. Check the No Paper Sensor Actuator. 3. Check for obstruction of the Pick mechanism.
Check the Tray 3 No Paper Sensor Actuator. The actuator is undamaged and motion is good. Y↓ N→Repair or replace the Tray 3 No Paper Sensor Actuator. Select dC330 code 07-310 to test the sensor. The sensor signal changes (high/low). Y↓ N→Remove the IOT, from the Feeder and check the Upper Option Harness, PL 8.30 Item 10. The harness is undamaged. Y↓ N→Replace the harness. Check the IOT Lower Option Harness. The harness is undamaged. Y↓ N→Replace the IOT Lower Option Harness. Replace the Tray 3 No Paper Sensor , then retest. The sensor signal changes. Y↓ N→Remove the Right Cover and reseat CN3 on the Feeder Board, then retest. The sensor signal changes. Y↓ N→Replace the MCU Board. Reassemble and perform SCP 6 Final Actions. Reassemble and perform SCP 6 Final Actions. Replace the MCU Board.

Code: 07-220-00

Description: Tray 3 is Open
Causes: The Size Switch indicates the Tray is not fully installed.
Remedy: 1. Close the Tray. 2. Check the Size Switch.
Cycle system power. The error message is displayed. Y↓ N→Complete. Remove Tray 3 and inspect the Size Switch. The Size Switch is undamaged. Y↓ N→Replace the Size Switch, then retest. Select dC330 code 07-300 to test the switch. The switch signals change (open/closed). Y↓ N→Remove the Right Cover and reseat CN5 on the Feeder Board, then retest. The sensor signal changes. Y↓ N→Replace the Feeder Board. Reassemble and perform SCP 6 Final Actions. Replace these components in order until the error is corrected. 1. Size Switch, PL 8.30 Item 9 2. Feeder Board, PL 8.30 Item 7 3. MCU Board, PL 3.10 Item 3
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie