Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Xerox Phaser 4600 — Trang 3/16

Code: 03-420-00

Description: Tray 3 Paper Mismatch
Causes: Media size setting for Tray 3 differ from those reported by the Size Switch.
Remedy: • Check media size settings for the tray from the Control Panel. • Reset the tray side and rear guides. • Check for obstructions blocking the Size Switch.
Cycle system power. The error message is displayed. Y↓ N→Complete. Inspect the Tray 2 end guide. The end guide operates the Size Switch actuators. Y↓ N→Replace the Tray, Select dC330 codes 07-320, 07-330, 07-340. The switches are operational (high/low). Y↓ N→Replace the Size Switch. Remove the IOT from the Feeder. Check the Tray 3 Upper Option Harness. The harness is undamaged. Y↓ N→Replace the Upper Option Connector. Check the IOT option connector. The harness is undamaged. Y↓ N→Replace the Lower Option Harness. Replace these components in order until the error is corrected. 1. Size Switch, PL 3.10 Item 9 2. Tray, PL 7.10 Item 23 3. Feeder Board, PL 8.30 Item 7 4. MCU Board, PL 3.10 Item 3

Code: 03-430-00

Description: Tray 4 Paper Mismatch
Causes: Media size setting for Tray 4 differ from those reported by the Size Switch.
Remedy: • Check media size settings for the tray from the Control Panel. • Reset the tray side and rear guides. • Check for obstructions blocking the Size Switch.
Cycle system power. The error message is displayed. Y↓ N→Complete. Inspect the Tray 4 end guide. The end guide operates the Size Switch actuators. Y↓ N→Replace the Tray, Select dC330 codes 07-420, 07-430, 07-440. The switches are operational (high/low). Y↓ N→Replace the Size Switch. Remove the IOT and Tray 3 from the Feeder. Check the Tray 4 Upper Option Harness. The harness is undamaged. Y↓ N→Replace the Upper Option Harness. Check option harness continuity through Trays 3 and 4. The connectors are undamaged. Y↓ N→Replace damaged connectors. Check the IOT Lower Option Harness. The harness is undamaged. Y↓ N→Replace the Lower Option Harness. Replace these components in order until the error is corrected. 1. Size Switch, PL 3.10 Item 9 2. Tray, PL 7.10 Item 23 3. Feeder Board, PL 8.30 Item 7 4. MCU Board, PL 3.10 Item 3

Code: 03-440-00

Description: Tray 5 Paper Mismatch RAP
Causes: 03-440-00 Media size setting for Tray 5 differ from those reported by the Size Switch.
Remedy: • Check media size settings for the tray from the Control Panel. • Reset the tray side and rear guides. • Check for obstructions blocking the Size Switch.
Cycle system power. The error message is displayed. Y↓ N→Complete. Inspect the Tray 5 end guide. The end guide operates the Size Switch actuators. Y↓ N→Replace the Tray, Select dC330 codes 07-520, 07-530, 07-540. The switches are operational (high/low). Y↓ N→Replace the Size Switch. Remove the IOT, Tray 3 and Tray 4 from the Feeder. Check the Tray 5 Upper Option Harness. The harness is undamaged. Y↓ N→Replace the Upper Option Harness. Check option harness continuity through all trays. The harnesses are undamaged. Y↓ N→Replace damaged harnesses. Check the IOT Lower Option Harness. The harness is undamaged. Y↓ N→Replace the Lower Option Harness. Replace these components in order until the error is corrected. 1. Size Switch, PL 3.10 Item 9 2. Tray, PL 7.10 Item 23 3. Feeder Board, PL 8.30 Item 7 4. MCU Board, PL 3.10 Item 3

Code: 03-450-00

Description: Tray 1 Paper Mismatch
Causes: Tray 1 is not configured with the proper media resources for the current job.
Remedy: • Check media size settings for the tray from the Control Panel. • Load Tray 1 with the media specified in the print job.
Cycle system power. The error message is displayed. Y↓ N→Complete. Select dC330 code 07-110. The sensor is operational (high/low). Y↓ N→Replace the Tray 1 No Paper Sensor. Remove the Tray 1 Feeder and inspect the wiring. The harness is undamaged and connected to the MCU Board. Y↓ N→Reconnect or repair the harness. Replace these components in order until the error is corrected. 1. Tray 1 Feeder, PL 8.10 Item 14 2. MCU Board, PL 3.10 Item 3

Code: 03-470-00

Description: Tray 6 Paper Mismatch
Causes: Media size setting for Tray 6 differ from those reported by the Size Switch.
Remedy: • Check media size settings for the tray from the Control Panel. • Reset the tray side and rear guides. • Check for obstructions blocking the Size Switch.
Cycle system power. The error message is displayed. Y↓ N→Complete. Inspect the Tray 6 end guide. The end guide operates the Size Switch actuators. Y↓ N→Replace the Tray, Select dC330 codes 07-620, 07-630, 07-640. The switches are operational (high/low). Y↓ N→Replace the Size Switch. Remove the IOT, Tray 3, 4 and 5 from the Feeder. Check the Tray 6 Upper Option Harness. The harness is undamaged. Y↓ N→Replace the Upper Option Harness. Check option harness continuity through all trays. The harnesses are undamaged. Y↓ N→Replace damaged harnesses. Check the IOT Lower Option Harness. The harness is undamaged. Y↓ N→Replace the Lower Option Harness. Replace these components in order until the error is corrected. 1. Size Switch, PL 3.10 Item 9 2. Tray, PL 7.10 Item 23 3. Feeder Board, PL 8.30 Item 7 4. MCU Board, PL 3.10 Item 3

Code: 03-480-00

Description: HCF Paper Mismatch
Causes: Media size setting for the HCF differs from those reported by the Size Switch. NOTE: Optional Tray numbering varies by configuration. When testing HCF components, use the dC330 codes appropriate for the HCF’s position. For example, if the configuration is 5 trays and the 5th tray is the HCF, use Tray 5 control codes.
Remedy: • Check media size settings for the HCF from the Control Panel. • Check for obstructions blocking the media guide.
Cycle system power. The error message is displayed. Y↓ N→Complete. Remove media and check operation of the length guide. The media guide moves smoothly. Y↓ N→Clear obstructions blocking guide movement. Select dC330 codes dependent on HCF position. The switches are operational (high/low). Y↓ N→Remove the IOT, Tray 3, and Tray 4 from the HCF. Check the HCF Option Harness. The harness is undamaged. Y↓ N→Replace the HCF Option Harness. Check option harness continuity through all trays. The harnesses are undamaged. Y↓ N→Replace damaged connectors. Check the IOT Lower Option Harness. The harness is undamaged. Y↓ N→Replace the Lower Option Harness. Replace the Size Switch, PL 7.25 Item 5. Replace these components in order until the error is corrected. 1. Size Switch, PL 7.25 Item 5 2. HCF Option Connector, PL 7.25 Item 15 3. Control Board, PL 7.25 Item 18 4. MCU Board, PL 3.10 Item 3

Code: 03-600-00

Description: A memory access failure has been detected within the Network Controller.
Causes: • Cycle system power. • Reseat or remove optional memory.
Remedy: Cycle system power. The error message is displayed. Y↓ N→Complete. Remove optional memory, if installed and retest. The error message is displayed. Y↓ N→Replace the optional memory using the instructions provided. Replace the IP Board.

Code: 03-800-00

Description: Hard Disk Drive Failure
Causes: A Hard Disk Drive access failure detected.
Remedy: • Cycle system power. • Reseat Hard Drive connection to the IP board.
Cycle system power. The error message is displayed. Y↓ N→Complete. Replace the Hard Drive using the instructions provided. The error message is displayed. Y↓ N→Complete. Replace the IP Board.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie