Causes: 03-130-00 A communication error has occurred between the MCU Board and Tray 4. 03-950-00 A communication error has occurred between the MCU Board and Tray 4.
Remedy: • Lock the feeder to Tray 3. • Reseat the IOT and Tray 3 on the Feeder. • Check for obstructions blocking the option harnesses. Cycle system power. The error message is displayed. Y↓ N→Complete. Remove the IOT and Tray 3 from the Feeder. Check feeder option harness continuity. The harnesses are undamaged. Y↓ N→Replace the damaged option harness. Check the IOT option connector. The harness is undamaged. Y↓ N→Replace the Lower Option Harness. Replace these components in order until the error is corrected. 1. Feeder Board, PL 8.30 Item 7 2. MCU Board, PL 3.10 Item 3
Causes: 03-140-00 A communication error has occurred between the MCU Board and Tray 5. 03-960-00 A communication error has occurred between the MCU Board and Tray 5.
Remedy: • Lock the feeder to Tray 5. • Reseat the IOT, Tray 3, and Tray 4 on the Feeder. • Check for obstructions blocking the option harnesses. Cycle system power. The error message is displayed. Y↓ N→Complete. Remove the IOT, Tray 3, and Tray 4 from the Feeder. Check feeder option harness continuity. The harnesses are undamaged. Y↓ N→Replace the damaged option harness. Check the IOT option harness. The harness is undamaged. Y↓ N→Replace the Lower Option Harness. Replace these components in order until the error is corrected. 1. Feeder Board, PL 8.30 Item 7 2. MCU Board, PL 3.10 Item 3
Causes: 03-150-00 A communication error has occurred between the MCU Board and Tray 6. 03-965-00 A communication error has occurred between the MCU Board and Tray 6.
Remedy: • Lock the feeder to Tray 6. • Reseat the IOT, Tray 3, Tray 4, and Tray 5 on the Feeder. • Check for obstructions blocking the option connections. Cycle system power. The error message is displayed. Y↓ N→Complete. Remove the IOT, Tray 3, Tray 4, and Tray 5 from the Feeder. Check feeder option connector continuity. The harnesses are undamaged. Y↓ N→Replace the damaged option harness. Check the IOT option connector. The harness is undamaged. Y↓ N→Replace the Lower Option Harness. Replace these components in order until the error is corrected. 1. Feeder Board, PL 8.30 Item 7 2. MCU Board, PL 3.10 Item 3
Causes: 03-160-00 A communication error has occurred between the MCU Board and the HCF. 03-990-00 A communication error has occurred between the MCU Board and the HCF.
Remedy: • Lock the feeder to the HCF. • Reseat the IOT, Tray 3, Tray 4, on the HCF. • Check for obstructions blocking the option connections. Cycle system power. The error message is displayed. Y↓ N→Complete. Remove the IOT and installed feeders from the HCF. Check the HCF option harness. The harness is undamaged. Y↓ N→Replace the damaged option harness. Check feeder option harness continuity for all feeders. The harnesses are undamaged. Y↓ N→Replace the damaged option harness. Check the IOT Lower Option Harness. The harness is undamaged. Y↓ N→Replace the Lower Option Harness. Replace these components in order until the error is corrected. 1. HCF Control Board, PL 7.25 Item 18 2. MCU Board, PL 3.10 Item 3
Causes: The Configuration Card is missing from its slot on the rear panel.
Remedy: • Reseat the Configuration Card. • Cycle system power. Cycle system power. The error message is displayed. Y↓ N→Complete. Remove and inspect the Configuration Card. The card is undamaged. Y↓ N→Replace the Configuration Card. Check the configuration card holder. The holder is secure. Y↓ N→Secure the holder to the IP Board. Install the card. Replace these components in order until the error is corrected. 1. Configuration Card, PL 3.10 Item 6 2. IP Board, PL 3.10 Item 2
Causes: 03-315-00 The Configuration Card is invalid for this system. 03-325-00 The Configuration Card is invalid for this system.
Remedy: • Reseat the Configuration Card. • Cycle system power. Cycle system power. The error message is displayed. Y↓ N→Complete. Remove and inspect the Configuration Card. The card is undamaged. Y↓ N→Replace the Configuration Card. Replace these components in order until the error is corrected. 1. Configuration Card, PL 3.10 Item 6 2. IP Board, PL 3.10 Item 2
Causes: The Configuration Card did not initialize.
Remedy: • Reseat the Configuration Card. • Cycle system power. Cycle system power. The error message is displayed. Y↓ N→Complete. Remove and inspect the Configuration Card. The card is undamaged. Y↓ N→Replace the Configuration Card. Replace these components in order until the error is corrected. 1. Configuration Card, PL 3.10 Item 6 2. IP Board, PL 3.10 Item 2
Causes: Media size setting for Tray 2 differs from the media size reported by the Tray 2 Size Switch.
Remedy: • Check media size settings for the tray from the Control Panel. • Reset the tray side and rear guides. • Check for obstructions blocking the Size Switch. Cycle system power. The error message is displayed. Y↓ N→Complete. Remove Tray 2 and inspect the Size Switch. The Size Switch is undamaged. Y↓ N→Replace the Size Switch. Inspect the Tray 2 end guide. The end guide operates the Size Switch actuators. Y↓ N→Replace the Tray, Select dC330 codes 07-220, 07-230, 07-240. The switches are operational (high/low). Y↓ N→Replace the Size Switch. Replace these components in order until the error is corrected. 1. Size Switch, PL 3.10 Item 9 2. Tray, PL 7.10 Item 23 3. MCU Board, PL 3.10 Item 3
Nhận ưu đãi sớm nhất khi chương trình diễn ra
Đăng ký nhận bản tin
Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này.
Chính sách cookie
Những cookie này là cần thiết để trang web hoạt động đúng cách.
Những cookie này giúp chúng tôi hiểu cách khách truy cập tương tác với trang web.
Những cookie này được sử dụng để cung cấp quảng cáo cá nhân hóa.