Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Xerox Phaser 4600 — Trang 6/16

Code: 07-230-00, 07-231-00

Description: Jam in Tray 3
Causes: 07-230-00 Jam 0 at Tray 3. Media did not exit the Tray 3 Pick Assembly. 07-231-00 Check Tray 3 Feed Area. Media remains at the Tray 3 Take Away Sensor.
Remedy: 1. Check for obstructions in the media path.
Check the Nudger, Feed, and Separator Rollers for excessive wear or contamination. The rollers are undamaged and clean. Y↓ N→Clean or replace the rollers. Check for obstructions or debris in the media path. The media path is clear. Y↓ N→Clear the media path of obstructions or debris. Check Tray 3 Pick Assembly (PL 8.20 Item 17) motion. Pick assembly motion is good. Y↓ N→Repair improper pick assembly motion. Select dC330 code 08-830 to test the Feed Clutch. The clutch is engaged (on/off). Y↓ N→Remove the Right Cover and reseat CN9 on the Feeder Board, then retest. The clutch is engaged. Y↓ N→Replace the Feed Clutch. Reassemble and perform SCP 6 Final Actions. Select dC330 code 08-930 to test the Feed Drive Assembly. The assembly rotates (on/off). Y↓ N→Remove the Right Cover and reseat CN7 on the Feeder Board, then retest. The Feed Drive Assembly rotates. Y↓ N→Replace the Feed Drive Assembly. Reassemble and perform SCP 6 Final Actions. Replace these components in order until the error is corrected. 1. Feed Assembly, PL 8.40 Item 10 2. Pick Assembly, PL 8.20 Item 17

Code: 07-310-00

Description: Paper Empty at Tray 4
Causes: The Tray 4 No Paper Sensor indicates Tray 4 is empty.
Remedy: 1. Check the No Paper Sensor Actuator. 2. Check for obstruction of the Pick mechanism.
Check the No Paper Sensor Actuator. The actuator is undamaged and motion is good. Y↓ N→Repair or replace the Tray 4 No Paper Sensor Actuator. Select dC330 code 07-410 to test the sensor. The sensor signal changes (high/low). Y↓ N→Remove the IOT and Tray 3. Check the option harness connections. The harness connectors are undamaged. Y↓ N→Replace any damaged harnesses. Reassemble the system to exchange Feeder positions. The error changes to the new feeder position. Y↓ N→Check the IOT Lower Option Harness. The harness is undamaged. Y↓ N→Replace the Lower Option Harness. Replace the MCU Board. Replace the No Paper Sensor , then retest. The signal changes. Y↓ N→Remove the Right Cover and reseat CN3 on the Feeder Board, then retest. The sensor signal changes. Y↓ N→Replace the Feeder Board. Reassemble and perform SCP 6 Final Actions. Reassemble and perform SCP 6 Final Actions. Replace the MCU Board.

Code: 07-320-00

Description: Tray 4 is Open
Causes: The Tray 4 Size Switch indicates Tray 4 is open.
Remedy: 1. Close the Tray. 2. Check the Size Switch.
Cycle system power. The error message is displayed. Y↓ N→Complete. Remove Tray 4 and inspect the Size Switch. The Size Switch is undamaged. Y↓ N→Replace the Size Switch, then retest. Select dC330 code 07-400 to test the switch. The switch signal changes (open/closed). Y↓ N→Remove the Right Cover and reseat CN5 on the Feeder Board, then retest. The sensor signal changes. Y↓ N→Replace the Feeder Board. Reassemble and perform SCP 6 Final Actions. Replace these components in order until the error is corrected. 1. Size Switch, PL 8.30 Item 9 2. Feeder Board, PL 8.30 Item 7 3. MCU Board, PL 3.10 Item 3

Code: 07-330-00, 07-331-00

Description: Jam in Tray 4
Causes: 07-330-00 Jam 0 in Tray 4. Media remains in the Tray 4 Pick-up Assembly. 07-331-00 Check Tray 4 Feed Area. Media remains at the Tray 4 Take Away Sensor.
Remedy: 1. Check for obstructions in the media path.
Check the Nudger, Feed, and Separator Rollers for excessive wear or contamination. The rollers are undamaged and clean. Y↓ N→Clean or replace the rollers. Check for obstructions or debris in the media path. The media path is clear. Y↓ N→Clear the media path of obstructions or debris. Check Tray 3 Pick Assembly (PL 8.20 Item 17) motion. Pick assembly motion is good. Y↓ N→Repair improper pick assembly motion. Select dC330 code 08-840 to test the Feed Clutch. The clutch is engaged (on/off). Y↓ N→Remove the Right Cover and reseat CN9 on the Feeder Board, then retest. The clutch is engaged. Y↓ N→Replace the Feed Clutch. Reassemble and perform SCP 6 Final Actions. Select dC330 code 08-940 to test the Feed Drive. The Feed Drive Assembly rotates (on/ off). Y↓ N→Remove the Right Cover and reseat CN7 on the Feeder Board, then retest. The Feed Drive Assembly rotates. Y↓ N→Replace the Feed Drive Assembly. Reassemble and perform SCP 6 Final Actions. Replace these components in order until the error is corrected. 1. Feed Assembly, PL 8.40 Item 10

Code: 07-410-00

Description: Paper Empty at Tray 5
Causes: The No Paper Sensor indicates Tray 5 is empty.
Remedy: 1. Check the No Paper Sensor Actuator. 2. Check for obstruction of the Pick mechanism.
Check the No Paper Sensor Actuator. The actuator is undamaged and motion is good. Y↓ N→Repair or replace the Tray 5 No Paper Sensor Actuator. Select dC330 code 07-510 to test the sensor. The sensor signal changes (high/low). Y↓ N→Remove the IOT, Tray 3 and Tray 4. Check the option harness connections. The harness connectors are undamaged. Y↓ N→Replace any damaged harnesses. Reassemble the system to exchange Feeder positions. The error changes to the new feeder position. Y↓ N→Check the IOT Lower Option Harness. The harness is undamaged. Y↓ N→Replace the Lower Option Harness. Replace the MCU Board. Replace the No Paper Sensor , then retest. The signal changes. Y↓ N→Remove the Right Cover and reseat CN3 on the Feeder Board, then retest. The sensor signal changes. Y↓ N→Replace the Feeder Board. Reassemble and perform SCP 6 Final Actions. Reassemble and perform SCP 6 Final Actions. Replace the MCU Board.

Code: 07-420-00

Description: Tray 5 is Open
Causes: The Size Switch indicates Tray 5 is not completely installed.
Remedy: 1. Close the Tray. 2. Check the Size Switch.
Cycle system power. The error message is displayed. Y↓ N→Complete. Remove Tray 5 and inspect the Size Switch. The Size Switch is undamaged. Y↓ N→Replace the Size Switch, then retest. Select dC330 code 07-500 to test the switch. The switch signals change (open/closed). Y↓ N→Remove the Right Cover and reseat CN5 on the Feeder Board, then retest. The sensor signal changes. Y↓ N→Replace the Feeder Board. Reassemble and perform SCP 6 Final Actions. Replace these components in order until the error is corrected. 1. Size Switch, PL 8.30 Item 9 2. Feeder Board, PL 8.30 Item 7 3. MCU Board, PL 3.10 Item 3

Code: 07-430-00, 07-431-00

Description: Jam in Tray 5
Causes: 07-430-00 Jam 0 in Tray 5. Media remains in the Tray 5 Pick-up Assembly. 07-431-00 Check Tray 5 Feed Area. Media remains at the Tray 5 Take Away Sensor.
Remedy: 1. Check for obstructions in the media path.
Check the Nudger, Feed, and Separator Rollers for excessive wear or contamination. The rollers are undamaged and clean. Y↓ N→Clean or replace the rollers. Check for obstructions or debris in the media path. The media path is clear. Y↓ N→Clear the media path of obstructions or debris. Check Tray 5 Pick Assembly (PL 8.20 Item 17) motion. Pick assembly motion is good. Y↓ N→Repair improper pick assembly motion. Select dC330 code 08-855 to test the Feed Clutch. The clutch is engaged (on/off). Y↓ N→Remove the Right Cover and reseat CN9 on the Feeder Board, then retest. The clutch is engaged. Y↓ N→Replace the Feed Clutch. Reassemble and perform SCP 6 Final Actions. Select dC330 code 08-950 to test the Feed Drive. The Feed Drive Assembly rotates (on/ off). Y↓ N→Remove the Right Cover and reseat CN7 on the Feeder Board, then retest. The Feed Drive Assembly rotates. Y↓ N→Replace the Feed Drive Assembly. Reassemble and perform SCP 6 Final Actions. Replace these components in order until the error is corrected. 1. Feed Assembly, PL 8.40 Item 10

Code: 07-500-00

Description: Paper Empty in Tray 1
Causes: The Tray 1 No Paper Sensor indicates Tray 1 is empty.
Remedy: 1. Add media to the Tray. 2. Check the No Paper Sensor Actuator.
Check the Tray 1 No Paper Sensor Actuator. The actuator is undamaged and motion is good. Y↓ N→Repair or replace the Tray 1 No Paper Sensor Actuator. Select dC330 code 07-110 to test the sensor. The sensor signal changes (high/low). Y↓ N→Replace the Tray 1 No Paper Sensor , then retest. The sensor signal changes. Y↓ N→Remove the Right Cover and reseat CN13 on the MCU Board, then retest. The sensor signal changes. Y↓ N→Replace the MCU Board. Reassemble and perform SCP 6 Final Actions. Reassemble and perform SCP 6 Final Actions. Replace the MCU Board.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie