Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Xerox WorkCentre 3655 — Trang 4/16

Code: 05-121-00

Description: CVT-DADF Feed Sensor On Jam 05-121-00 The feed sensor is not turned on in the time specified. In Duplex mode, the feed sensor is not turned on after a specified time
Remedy: Open the DADF Top Cover and clean the area surrounding the DADF Pick-up Assembly. The error persists. Y↓N→Perform SCP 6 Final Actions. Clean or replace the DADF Pick-up Assembly . The error persists. Y↓N→Perform SCP 6 Final Actions. Install new components as necessary: • DADF Pick-up Assembly • DADF Assembly • IIT Control Board

Code: 05-900-00

Description: ADF Sensor Static Jam 05-900-00 The DADF Top Cover interlock switch is opened during DADF operation. Paper remains in paper path after cover is closed..
Remedy: Check the DADF Top Cover properly actuates the interlock switch. The error persists. Y↓N→Perform SCP 6 Final Actions. Replace the DADF Assembly .

Code: 05-940-00

Description: DADF No Original Fail 05-940-00 Original has been removed. Status code 05-535 is raised with this fault code.
Remedy: Open the DADF Top Cover and clean the area surrounding the DADF Pick-up Assembly. The error persists. Y↓N→Perform SCP 6 Final Actions. Clean or replace the DADF Pick-up Assembly . The error persists. Y↓N→Perform SCP 6 Final Actions. Install new components as necessary: • DADF Pick-up Assembly • DADF Assembly • IIT Control Board

Code: 10-311-00 ... 10-376-00

Description: Fuser Thermal Error 10-311-00 Center STS sensor burnout detection 10-321-00 Hard Relay OFF 10-324-00 Sub lamp ON consecutive errors 10-326-00 Cool Down Timeout 10-328-00 Warming up - timeout 10-334-00 STS center-side sensor failure 10-337-00 Heat Roll Paper twine Error 10-338-00 Main lamp ON consecutive errors 10-372-00 Center STS High-temperature anomaly 10-373-00 Side STS Disconnection abnormality 10-374-00 Side STS High-temperature anomaly 10-375-00 Center STS Low-temperature anomaly 10-376-00 Side STS Low-temperature anomaly
Remedy: Cycle system power. The error persists. Y↓N→Go to SCP 6 and complete the Final Actions. Replace the Fuser

Code: 10-420-00, 10-421-00

Description: Fuser End of Life 10-420-00 Fuser Assy Near Life. Status code 10-524 is raised with this fault code. 10-421-00 Fuser Assy Life End. Status code 10-523 is raised with this fault code.
Remedy: Check the Fuser life count. Fuser life count is at or near end of life. Y↓N→Cycle system power. The error message is displayed. Y↓N→Reassemble and perform SCP 6 Final Actions. Replace the Fuser . Replace the Fuser

Code: 10-902-00

Description: Fuser Missing
Remedy: Reseat the Fuser. The error persists. Y↓N→Go to SCP 6 and complete the Final Actions. Replace the Fuser .

Code: 10-903-00

Description: Main Error updating data NOTE: Status codes 03-561 and 10-527 are raised with this fault code.
Remedy: Cycle system power. The error persists. Y↓N→Go to SCP 6 and complete the Final Actions. Replace the Fuser .

Code: 12-930-00

Description: Exit Tray Full
Remedy: Cycle system power. The error persists. Y↓N→Go to SCP 6 and complete the Final Actions. Use dC330 code 71-122 to check Full Stack Sensor operation. The sensor signal changes. Y↓N→Remove the Exit Chute Assembly to check the sensor, acutator, and harness. The sensor is connected and the harness undamaged. Y↓N→Replace the Full Stack Sensor or repair the harness. If the actuator is damaged, replace the Exit Chute Assembly. Replace the MCU Board Install new components as necessary: • Full Stack Sensor • Exit Chute Assembly • MCU Board
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie